• 전기학회논문지
• /
• 제59권2호
• /
• pp.355-358
• /
• 2010

As CMOS technology continues to scale down, signal processing is favorably done in the digital domain, which requires Analog-to-Digital (A/D) Converter to be integrated on-chip. This paper presents a design methodology of 12-bit 1-MS/s Rail-to-Rail fully differential SAR ADC using Deep N-well Switch based on binary search algorithm. Proposed A/D Converter has the following architecture and techniques. Firstly, chip size and power consumption is reduced due to split capacitor array architecture and charge recycling method. Secondly, fully differential architecture is used to reduce noise between the digital part and converters. Finally, to reduce the mismatch effect and noise error, the circuit is designed to be available for Rail-to-Rail input range using simple Deep N-well switch. The A/D Converter fabricated in a TSMC 0.18um 1P6M CMOS technology and has a Signal-to-Noise-and-Distortion-Ratio(SNDR) of 69 dB and Free-Dynamic-Range (SFDR) of 73 dB. The occupied active area is $0.6mm^2$.

• Geomechanics and Engineering
• /
• 제30권5호
• /
• pp.401-411
• /
• 2022

To obtain the dynamic mechanical properties, fracture modes, energy and brittleness characteristics of Furong Baijiao coal rock, the dynamic impact compression tests under 0, 4, 8 and 12 MPa confining pressure were carried out using the split Hopkinson pressure bar. The results show that failure mode of coal rock in uniaxial state is axial splitting failure, while it is mainly compression-shear failure with tensile failure in triaxial state. With strain rate and confining pressure increasing, compressive strength and peak strain increase, average fragmentation increases and fractal dimension decreases. Based on energy dissipation theory, the dissipated energy density of coal rock increases gradually with growing confining pressure, but it has little correlation with strain rate. Considering progressive destruction process of coal rock, damage variable was defined as the ratio of dissipated energy density to total absorbed energy density. The maximum damage rate was obtained by deriving damage variable to reflect its maximum failure severity, then a brittleness index BD was established based on the maximum damage rate. BD value declined gradually as confining pressure and strain rate increase, indicating the decrease of brittleness and destruction degree. When confining pressure rises to 12 MPa, brittleness index and average fragmentation gradually stabilize, which shows confining pressure growing cannot cause continuous damage. Finally, integrating dynamic deformation and destruction process of coal rock and according to its final failure characteristics under different confining pressures, BD value is used to classify the brittleness into four grades.

• 약학회지
• /
• 제49권6호
• /
• pp.449-458
• /
• 2005

There have been rapid changes in the pharmaceutical environment after the separation of Dispensing and Prescribing practice. In the early stage of this system, outpatients had few options to choose their pharmacies due to various obstacles. Under these circumstances, this study on the defection tendency of long-term care patients was performed through the analysis of outpatients who quit visiting a pharmacy nearby general hospital. PowerBuilder ver 9.0 program was used to extract significant data, and SPSS package was employed for statistic analysis. 3,308 outpatients who visited a pharmacy nearby hospital for a month (in January, 2004) were studied. Patients' sex, age and location of residence, the class of medical insurance, the characteristic type of medication (powder, split form, medication for external use/injection), waiting time, disease (department) were considered as variable factors. It turned out that the patient revisit ratio was 80.8$\%$ and the patient defection ratio was 32.4$\%$. As was expected, those factors mentioned above influenced on the revisit and defection ratio considerably. In terms of patient factors, it proved that there was no relationship among sex, location of residence, the class of medical insurance and revisit (defection) ratio. Only age factor influenced the ratio; the older, the higher revisit ratio and the less defection ratio. In respect of dispensing factors, there were obvious relationships among the factors and the ratio: bill (money they had to pay individually), waiting time, number of medications, splitting of tablets, unit price of drug and revisit (defection) ratio showed significant relationship. The result of this study revealed an aspect of outpatients' behavior and it could be used as a reference for better patient service and customer relationship management.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 추계학술대회 논문집
• /
• pp.353-356
• /
• 2008

HEV(Hybrid Electrical Vehicle) is considered as one of the next generation vehicles. To develop the HEV, there must be a reliable simulator, by which the capacities of the power resources are tested, and the parameters of the HEV are optimized before developing the real model of the HEVs. This process can save the money for designing the HEV system and improve the system without experiments. Matlab Simulink is familiar to mechanical engineers and the program can simultaneously provide a system model and a controller in one program. Nowadays, the Simdriveline toolbox which is used for analysis a power-train system is applied to build a dynamic model for a HEV system. In this study, we make a HEV simulator with the Simdriveline toolbox and develop a controller. There are two simple strategies, applied to the controller. One strategy includes a power split ratio and a shift map which are created by user. Other strategy calculated an appropriate amount of resource's torque along specific results, and this is useful when users can't develop a fitting controller. The methodologies for configuring the simulator and its control system are presented in this paper.

• 한국음향학회지
• /
• 제15권6호
• /
• pp.81-89
• /
• 1996

원전의 1차 계통 건전성 확보를 위한 일환으로서 초음파 검사 방법은 매우 중요하다. 그러나, 초음파는 검사 대상제의 내부 구조 및 형상에 따라 검사의 제한을 받으므로 결정립이 큰 재질에서 후방 산란 잡음 즉 시 불변성(time invariant) 잡음이 발생한다. 이로 인하여 수신 신호는 낮은 신호 대 잡음비의 결과로 나타나게 된다. 주파수 대역 분할 방식(split spectrum processing:SSP) 기술은 이와 같은 잡음을 억제하는데 효율적이다. 그러나, 종래의 SSP 기술은 minization, PT 알고리즘중 한 알고리즘만 적용하였으나 본 논문에서는 이두 가지 알고리즘을 동시에 처리하는 MPO(minimization and polarity threshold)알고리즘을 적용하고, 주파수 대 대역폭비가 일정한 FIR 여파기로서 새로운 constant-Q SSP를 수행하여 신호처리 시간을 단축하였다. 현장 검사 요건과 동일하게 종파와 횡파에도 일부 적용하였다. 한편, 이러한 새로운 SSP 기술을 적용할 수 있도록 초음파 탐상기를 설계 제작하였고, 시험편들의 준비는 원전 모재 대비시험편, 모재와 동일한 재질의 스테인레스 스틸 및 구리 시험편들이며, 이들 시험편으로 부터 초음파 신호를 수집하여 본 신호 처리를 적용한 결고 신호 대 잡음비가 향상됨을 알 수 있었다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2002년도 전력전자학술대회 논문집
• /
• pp.343-346
• /
• 2002

In recent, complex SVPWM (Space Vector PWM) algorithm can be easily implemented by high performance microprocessor and DSP. Various SVPWM techniques are widely studied due to the advantages of low harmonic distortion and high use ratio of D.C. link voltage. Most of various studies for improving of VS-PWM inverter performance are concentrated about switching pattern and zero pulse pattern split algorithms. However, dc link voltage that is determined at rated load and speed conditions is not proper in the low speed and under rated load. In this paper, analysis of current ripple with digitally implemented SVPWM inverter is introduced according to link voltage. The optimal link voltage in the designed inverter system and load condition is provided in order to suppress output voltage error and current ripple. As remaining the effective voltage vector interval per sampling period sufficiently, additional voltage error and current ripple are suppressed. The proposed algorithm is verified through digital simulation and experimental results.

• 에너지공학
• /
• 제28권4호
• /
• pp.13-18
• /
• 2019

The high energy penalty in amine-based post-combustion CO₂ capture process is hampering its industrial scale application. An advanced process is designed by intensive heat integration within the conventional process to reduce the stripper duty. The study presents the technical feasibility for stripper duty reduction by intensive heat integration in CO₂ capture process. A rigorous rate-based model has been used in Aspen Plus® to simulate conventional and advanced process for a 300 MW coal-based power plant. Several design and operational parameters like split ratio, stripper inter-heater location and flowrate were studied to find the optimum values. The results show that advanced configuration with heat integration can reduces the stripper heat by 14%.

• 한국통신학회논문지
• /
• 제27권1B호
• /
• pp.56-65
• /
• 2002

본 논문에서는 IS-2000 시스템에 적합한 심볼 분할 OTD (orthogonal transmit diveristy)를 제안하였다. 심볼 분할 OTD는 Meyer가 제안한 심볼 분할과 OTD를 결합하여 최대 경로 다이버시티 및 시간 다이버시티 이득을 얻기에 IS-2000 순방향 성능을 개선시킬 수 있다. 이를 IS-2000 표준의 순방향 fundamental 채널에 대하여 시뮬레이션을 통해 확인하였다. 그리고, 그 결과를 기존의 IS-2000 표준에서 채택된 OTD와 STS (space-time spreading)의 성능과 비교하였다. 본 논문에서 제안한 방법을 IS-2000 시스템에 적용할 경우, 1% FER (frame error rate)을 얻기 위한 송신전력이 OTD의 경우보다 0.5-7.7dB 정도 감소되어 STS의 성능과 거의 일치하였다. 뿐만 아니라, 송신신호의 PAR(peak-to-average power ratio)가 STS보다 적으므로, 기지국 전력증폭기와 같은 RF 회로의 복잡도를 감소시킬 수 있는 장점이 있다.

• Journal of Power Electronics
• /
• 제19권6호
• /
• pp.1351-1365
• /
• 2019

This paper proposes two modified Z-source inverter topologies, namely an embedded L-Z-source inverter (EL-ZSI) and a coupled inductor L-Z source inverter (CL-ZSI). The proposed topologies offer a high voltage gain with a reduced passive component count and reduction in source current ripple when compared to conventional ZSI topologies. Additionally, they prevent overshoot in the dc-link voltage by suppressing heavy inrush currents. This feature reduces the transition time to reach the peak value of the dc-link voltage, and reduces the risk of component failure and overrating due to the inrush current. EL-ZSI and CL-ZSI possess all of the inherent advantages of the conventional L-ZSI topology while eliminating its drawbacks. To verify the effectiveness of the proposed topologies, MATLAB/Simulink models and scaled down laboratory prototypes were constructed. Experiments were performed at a low shoot through duty ratio of 0.1 and a modulation index as high as 0.9 to obtain a peak dc-link voltage of 53 V. This paper demonstrates the superiority of the proposed topologies over conventional ZSI topologies through a detailed comparative analysis. Moreover, experimental results verify that the proposed topologies would be advantageous for renewable energy source applications since they provide voltage gain enhancement, inrush current, dc-link voltage overshoot suppression and a reduction of the peak to peak source current ripple.

• 한국작물학회지
• /
• 제37권5호
• /
• pp.405-412
• /
• 1992

경운과 무경운 조건에서 수도를 건답휴립직파할 때 질소분시비율이 수도의 생육과 수량성에 미치는 영향을 알기 위하여 직파재배용으로 육성중인 밀양 9005의 건조종자를 6kg / 10a 수준으로 1990년 5월 17일 산파하고, 맥류휴립산파기로 복토하였다. 질소-인산-가리를 15-10-10kg /10a 수준으로 시용하였는데 인산과 가리는 모두 기비로 시용하였다. 질소는 기비 : 담수직후 : 담수 2주후 : 출수 25일전 : 출수기에 요소를 10 : 20 : 30 : 20 : 20%, 20 : 30 : 20 : 20 : 10%, 30 : 40 : 0 : 20 : 10%로 분시하였고, 완효성시비료는 질소가 40%이고, 비효특속기간이 120일인 latex 피복한 요소를 전량기비로 시용하였다. 경운에서는 무경운에 비하여 출수기가 1일 지정되었고, 출수기의 엽면적지수가 컸으며, 도복지수가 적었을 뿐 입묘수, 수량, 수량구성요소, 도복관련형질 및 간기부의 cellulose, hemicellulose, lignin 함량은 차이가 없었다. 질소분시비율간에는 완효성비료 전량기비구에서 간장, 유효경비율, 간기중, 천립중, 수확지수가 더 컸으며, 무경운의 완효성비료 전량시비구에서 수량이 더 높았다. 완효성비료 시용구에서는 생육 초기에는 질소함유율과 흡수량이 가장 낮았지만, 출수기 이후에는 질소함유율과 흡수량은 다른 질소분시구보다 높았다. 분얼수는 완효성비료 시용구에서 가장 낮았고, 생육초기에는 질소의 기비비율이 높을수록 많았으며, 생육중기에는 20 : 30 : 20 : 20 : 10%의 분얼수가 가장 높았지만 유효경비율이 달라 수수는 처리간에 차이가 없었다.