• Proceedings of the IEEK Conference
• /
• 2002.07c
• /
• pp.1701-1704
• /
• 2002

In this paper, we investigate the effect of power control step size on the performance of the SIC scheme in DS/CDMA systems. We investigate the average power control iteration and its standard deviation and evaluate the outage performance for several different values of power control step size. Because the SIC scheme requires fine control in the received signal power, the better outage performance is obtained fer the smaller power control step size. However, the smaller power control step size requires larger amount of power control iteration in order to make the power control converge to the steady state. Under the simulated environment, the proper power control step size is about 0.3-0.4dB from both convergence speed of power control algorithm and outage performance points of view.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.3
• /
• pp.205-212
• /
• 2012

This paper proposes the fuzzy logic based variable step-size MPPT (Maximum Power Point Tracking) method for the stability at the steady state and the improvement of the transient response in the wind power system. If the change value of duty ratio is set on stability of the steady state, MPPT control traces to maximum power point slowly. And if the change value is set on improvement of the transient response, the system output oscillates at the maximum power point. By adjusting the step size with fuzzy logic, it can be improved the MPPT response speed and stability at steady state when MPPT control is performed to track the maximum power point. The effectiveness of the proposed method has been verified by simulations and experimental results.

• Communications for Statistical Applications and Methods
• /
• v.22 no.4
• /
• pp.389-399
• /
• 2015

It is important not to overcalculate sample sizes for clinical trials due to economic, ethical, and scientific reasons. Kang and Kim (2014) investigated the accuracy of a well-known sample size calculation formula based on the approximate power for continuous endpoints in equivalence trials, which has been widely used for Development of Biosimilar Products. They concluded that this formula is overly conservative and that sample size should be calculated based on an exact power. This paper extends these results to binary endpoints for three popular metrics: the risk difference, the log of the relative risk, and the log of the odds ratio. We conclude that the sample size formulae based on the approximate power for binary endpoints in equivalence trials are overly conservative. In many cases, sample sizes to achieve 80% power based on approximate powers have 90% exact power. We propose that sample size should be computed numerically based on the exact power.

• Genomics & Informatics
• /
• v.10 no.2
• /
• pp.117-122
• /
• 2012

A sample size with sufficient statistical power is critical to the success of genetic association studies to detect causal genes of human complex diseases. Genome-wide association studies require much larger sample sizes to achieve an adequate statistical power. We estimated the statistical power with increasing numbers of markers analyzed and compared the sample sizes that were required in case-control studies and case-parent studies. We computed the effective sample size and statistical power using Genetic Power Calculator. An analysis using a larger number of markers requires a larger sample size. Testing a single-nucleotide polymorphism (SNP) marker requires 248 cases, while testing 500,000 SNPs and 1 million markers requires 1,206 cases and 1,255 cases, respectively, under the assumption of an odds ratio of 2, 5% disease prevalence, 5% minor allele frequency, complete linkage disequilibrium (LD), 1:1 case/control ratio, and a 5% error rate in an allelic test. Under a dominant model, a smaller sample size is required to achieve 80% power than other genetic models. We found that a much lower sample size was required with a strong effect size, common SNP, and increased LD. In addition, studying a common disease in a case-control study of a 1:4 case-control ratio is one way to achieve higher statistical power. We also found that case-parent studies require more samples than case-control studies. Although we have not covered all plausible cases in study design, the estimates of sample size and statistical power computed under various assumptions in this study may be useful to determine the sample size in designing a population-based genetic association study.

• Journal of Power Electronics
• /
• v.15 no.2
• /
• pp.487-496
• /
• 2015

In order to ensure that photovoltaic (PV) systems work at the maximum power point (MPP) and maximize the economic benefits, maximum power point tracking (MPPT) techniques are normally applied to these systems. One of the most widely applied MPPT methods is the incremental conductance (INC) method. However, the choice of the step size still remains controversial. This paper presents an improved variable step size INC MPPT algorithm that uses four different step sizes. This method has the advantages of INC but with the ability to validly adjust the step size to adapt to changes of the PV's power curve. The presented algorithm also simultaneously achieves increased rapidity and accuracy when compared with the conventional fixed step size INC MPPT algorithm. In addition, the theoretical derivation and specific applications of the proposed algorithm are presented here. This method is validated by simulation and experimental results.

• Fashion & Textile Research Journal
• /
• v.4 no.1
• /
• pp.86-91
• /
• 2002

To estimate dispersion stability of particles, suspending power and particle size were examined as functions of pHs, surfactants, electrolytes and ionic strengths using ${\alpha}-Fe_2O_3$ particle as the model of particulate soil. Suspending power and particle size were determined by UV-Vis spectrumeter and by light scattering using the polarization ratio method, respectively. The suspending power was relatively high with polyanion electrolytes and was low with neutral salts. The suspending power was biphasis, minimum pH 6~7, and the effect of surfactant on the suspending power was insignificant. Generally suspending power increased with decreasing the particle size governed aggregation of dispersed particles regardless of solution conditions. Hence the suspending power was inversely related to the particle size.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.3
• /
• pp.492-498
• /
• 2010

Since it is almost impossible to train the dispatchers with real power system, the dispatcher training simulator(DTS) is used for the training. Among various components of the DTS, the power system model(PSM) emulates the dynamic behavior of the power system to calculate the frequency and voltage. The frequency is calculated from various parameters such as mechanical power of power plants, load, inertia, and the damping of the power system. In the PSM, the power plants are modeled as differential equations, so the mechanical power of the power plants are calculated by the numerical methods. Conventionally, the fixed step-size algorithm has been used in the PSM, however it has some drawbacks. This paper develops the prototype PSM using the Matlab, and analyzes the problems of the fixed step-size algorithm by comparing the results with those of PSCAD simulation. In order to overcome the limitations, this paper proposes a modified frequency calculation method using the adaptive step-size algorithm. From the simulation using the proposed method, it is verified that the accuracy of frequency calculation increases substantially while the simulation time is not greatly increased.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.9
• /
• pp.1535-1542
• /
• 2007

HTS (High Temperature Superconducting) Power devices has the several useful characteristics from the technical and economical viewpoint. Possible application to the utility industry have been widely discussed in various research projects. For the successful introduction of HTS power devices into power system, establishing a proper R&D and marketing strategies through estimating the future market size are necessary. However, quantitative estimates of how well HTS power devices will serve their markets have been lacking. In this paper, we propose a estimation methodology of future market size for HTS power divices such as cable, transformer, generator, and motor, and also evaluate the future international and domestic market size by using proposed methodology.

• Journal of Power Electronics
• /
• v.11 no.2
• /
• pp.218-227
• /
• 2011

The subject of variable step size maximum power point tracking (MPPT) algorithms has been addressed in the literature. However, most of the addressed algorithms tune the variable step size according to two variables: the photovoltaic (PV) array voltage ($V_{PV}$) and the PV array current ($I_{PV}$). Therefore, both the PV array current and voltage have to be measured. Recently, maximum power point trackers that arc based on a single variable ($I_{PV}$ or $V_{PV}$) have received a great deal of attention due to their simplicity and ease of implementation, when compared to other tracking techniques. In this paper, two methods have been proposed to design a variable step size MPPT algorithm using only a single current sensor for stand-alone battery storage PV systems. These methods utilize only the relationship between the PV array measured current and the converter duty cycle (D) to automatically adapt the step change in the duty cycle to reach the maximum power point (MPP) of the PV array. Detailed analyses and flowcharts of the proposed methods are included. Moreover, a comparison has been made between the proposed methods to investigate their performance in the transient and steady states. Finally, experimental results with field programmable gate arrays (FPGAs) are presented to verify the performance of the proposed methods.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.4
• /
• pp.551-559
• /
• 2008

Increase in power consumption can cause a serious stability problem of an electric power system without construction of new power plants or transmission lines. Also, it can generate large power loss of the system. In costly and environmentally effective manner to avoid constructing the new infrastructures such as power plants and transmission lines, etc, the distributed generation(DG) has paid great attentions so far as a solution for the above problem. Selection of optimal location and size of the DG is the necessary process to maintain the stability and reliability of existing system effectively. However, the systematic and cardinal rule for this issue is still open question. In this paper, the method to determine optimal location of the DG is proposed by considering power loss when the DG is connected to an electric power grid. Also, optimal size of not only the corresponding single DG but also the multi-DGs is determined with the proposed systematic approach. The IEEE benchmark 30-bus test system is analyzed to evaluate the feasibility and effectiveness of the proposed method.