• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.4
• /
• pp.75-79
• /
• 2013

A power distribution network (PDN) is a network that provides connection between the voltage source supply and the power/ground terminals of a microprocessor chip. It consists of a voltage regulator module, a printed circuit board, a package substrate, a microprocessor chip as well as decoupling capacitors. For power integrity analysis, the board and package layouts have to be transformed into an electrical network of resistor, inductor and capacitor components which may be expressed using the S-parameters models. This modeling process generally takes from several hours up to a few days for a complete board or package layout. When the board and package layouts change, they need to be re-extracted and the S-parameters models also need to be re-generated for power integrity assessment. This not only consumes a lot of resources such as time and manpower, the task of PDN modeling is also tedious and mundane. In this paper, a block-based PDN modeling is proposed. Here, the board or package layout is partitioned into sub-blocks and each of them is modeled independently. In the event of a change in power rails routing, only the affected sub-blocks will be reextracted and re-modeled. Simulation results show that the proposed block-based PDN modeling not only can save at least 75% of processing time but it can, at the same time, keep the modeling accuracy on par with the traditional PDN modeling methodology.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.2
• /
• pp.182-189
• /
• 2016

A modeling method of electric power network inside a fishing boat less than 5 tons is proposed for its high-energy efficiency with renewable energy sources. The power network inside the fishing boat consists of a diesel engine, a starter motor, an alternator, battery packs, and electric loads, which are connected in parallel. To obtain proper power network model, the voltage -current characteristics of the electric components are considered to develop elaborate electrical models under several load conditions. Measured data of the battery and alternator current include noise. By using an average method, the AC components from the power network of the fishing boat can be reduced, which is verified by KCL rule. Using the proposed power network model, the power generation of the alternator and the reduction of diesel consumption in the boat's engine are predictable under various operating conditions. The validity of the proposed methodology is verified by comparing simulation results with experimental measurements using statistical inferences.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.6
• /
• pp.283-290
• /
• 2013

This paper illustrates the possibilities of using the program ATP-Draw (Alternative Transient Program) for the modeling of power networks to study power quality problems with highly detailed analyses. The Program ATP-Draw is one of the most widespread and oldest programs. A unique characteristic of this program is its public domain and the existence of forums and study committees where new application cases and modification are presented and shared publicly. In this paper, to study the propagation of harmonics through a power network, a part of an industrial power network was modeled. The network contains different types of electric components, such as transformers, transmission lines, cables and loads, and there is a source of harmonics that injects $3^{rd}$, $5^{th}$, $7^{th}$, $9^{th}$ and $11^{th}$ harmonic currents into the network, causing a distortion of the wave form of the currents and voltages through the power network.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.488-491
• /
• 1997

The PMGS(Plant Model Generating System) was developed based on modular modeling method and fluid network calculation concept. Fluid network calculation is used as a method of real-time computation of fluid network, and the module which has a topology with node and branch is defined to take advantages of modular modeling. Also, the database which have a shared memory as an instance is designed to manage simulation data in real-time. The applicability of the PMGS was examined implementing the HRSG(Heat Recovery Steam Generator) control logic on DCS.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.62 no.2
• /
• pp.65-71
• /
• 2013

Nonlinear loads with harmonics exist in an actual power system where harmonic currents make voltage distortion. The sum of reactive power measured at individual load is different from the measured reactive power at a bus in a power system with linear and non-linear loads. In this study, ANN(artificial neural network) load modeling technique with consideration of harmonics is introduced for more accurate component load modeling and an impact coefficient is proposed for aggregation of component loads. Results of this research show more accurate load modeling method. Since precise data for power system analysis can be acquired, the proposed method will be used for power system planning and maintenance.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.261-264
• /
• 2004

In this paper, we identify the memory effect of high power(125W) laterally diffused metal oxide-semiconductor(LDMOS) RF Power Amplifier(PA) by two tone IMD measurement. We measure two tone IMD by changing the tone spacing and the power level. Different asymmetric IMD is founded at different center frequency measurements. We propose the Tapped Delay Line-Neural Network(TDNN) technique as the modeling method of LDMOS PA based on two tone IMD data. TDNN's modeling accuracy is highly reasonable compared to the memoryless adaptive modeling method.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.4
• /
• pp.551-560
• /
• 1998

This paper presents a neural network model representing complex hydro-thermo-dynamic characteristics of a steam generator in nuclear power plants. The key modeling processes include training data gathering process, analysis of system dynamics and determining of the neural network structure, training process, and the final process for validation of the trained model. In this paper, we suggest a training data gathering method from an unstable steam generator so that the data sufficiently represent the dynamic characteristics of the plant over a wide operating range. In addition, we define the inputs and outputs of neural network model by analyzing the system dimension, relative degree, and inputs/outputs of the plant. Several types of neural networks are applied to the modeling and training process. The trained networks are verified by using a class of test data, and their performances are discussed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.7
• /
• pp.1320-1326
• /
• 2010

In this paper, we develop a design methodology of granular-based neurocomputing networks realized with the aid of the clustering techniques. The objective of this paper is modeling and evaluation of approximation and generalization capability of the Linear-Type Superconducting Power Supply (LTSPS). In contrast with the plethora of existing approaches, here we promote a development strategy in which a topology of the network is predominantly based upon a collection of information granules formed on a basis of available experimental data. The underlying design tool guiding the development of the granular-based neurocomputing networks revolves around the Fuzzy C-Means (FCM) clustering method and the Radial Basis Function (RBF) neural network. In contrast to "standard" Radial Basis Function neural networks, the output neuron of the network exhibits a certain functional nature as its connections are realized as local linear whose location is determined by the membership values of the input space with the aid of FCM clustering. To modeling and evaluation of performance of the linear-type superconducting power supply using the proposed network, we describe a detailed characteristic of the proposed model using a well-known NASA software project data.

• Journal of the Korean Society of Industry Convergence
• /
• v.14 no.3
• /
• pp.95-100
• /
• 2011

The modern society longing for the convenience of up-to-date technology, there are attempts of miniaturization and high reliance of power equipments in the effectiveness aspect of urban area's usage of space while requiring more electrical energy than now. Consequently, paper used to the Neral Network for a forcasting conservation system. A neral network is powerful asta modeling tool that is able to capture and represent complex input/output relationships. The true power and advantage of neral networks lies in their ability to learn these relationships directly from the data being modeled. Traditional linear models are simply inadequate when it comes to modeling data that contains non-linear characteristics. Form results of this study, the Neral Network is will play an important role for insulation diagnosis system of real site GIS and power eqipment using $SF_6$ gas.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.10
• /
• pp.1842-1848
• /
• 2009

This paper summarizes a data modeling for developing the baseline network analysis software of the Korean energy management system (EMS). The study is concentrated on the following aspects. First, the data for operating the each application software are extracted. Some of the EMS network application softwares are selected for basis model. Those are based on the logical functions of each software and are not considered the other softwares. Second, the common data are extracted for equipment model and topological structure of power system in Korea. We propose the application common model(ACM) that can be applied whole EMS network application softwares. The ACM model includes the hierarchy and non-hierarchy power system structure, and is connected each other using the direct and indirect link. Proposed database model is tested using the Korea Electric Power Corporation(KEPCO) system. The real time SCADA data are provided for the test. Through the test, we verified that the proposed database structure can be effectively used to accomplish the Korean EMS system.