• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.8
• /
• pp.115-122
• /
• 2017

In this paper, we propose a novel power factor compensation system using slidac. The proposed power factor compensation system compensates the power factor by adjusting the output voltage of the slidac. In the conventional power factor compensation system using capacitor bank method, the power factor compensation error occurs depending on the load condition due to the limitation of the compensation capacitor capacity. However, the proposed system can finely change slidac output voltage applied to the capacitor, therefore power factor can be compensated up to 100% without error. We compare the proposed system with the conventional system, and confirm that the proposed system has excellent power factor compensation performance through simulations and experiments. If the proposed power factor compensation system is applied to an industrial field, a power factor compensation performance can be maximized. As a result, it is possible to reduce of electricity prices, reduce of line loss, increase of load capacity, ensure the transmission margin capacity, and reduce the amount of power generation.

• Proceedings of the KIEE Conference
• /
• 1999.11b
• /
• pp.83-85
• /
• 1999

Recently, a rapid increase of electricity demands have made Transmission & Substation device large-sized. complicated and diverse. Moreover, a rising level of customer's requirement and high growth of industry increase the reliability of electricity service. Therefore on the basis of the case study on the occurrence of fault, the prevention of defects for each device and the analyzing of the outbreak and prevention of systematic breakdown in Sin-Incheon Power Transmission Branch Office, this paper presents some important matters and suggests the method of improvement in design, construction, maintenance, and repairing the Transmission & Substation device.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.3
• /
• pp.283-289
• /
• 2014

This paper carries out a series of analysis of power system using Gallium Nitride (GaN) FET which has wide band gap (WBG) characteristics comparing to conventional Si MOSFET-used power system. At first, for comparison of each semiconductor device, the switching-transient parameter is quantitatively extracted from released information of GaN FET. And GaN FET model which reflect this dynamic property is configured. By using this model, the performance of GaN FET is analyzed comparing to Si MOSFET. Also, in order to enable a representative assessment on the power system level, Si MOSFET and GaN FET are applied to the most common structure of power system, full-bridge, and each power systems are compared based on various criteria, such as performance, efficiency and power density. The entire process is verified with the aid of mathematical analysis and simulation.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.2
• /
• pp.569-575
• /
• 2014

A highly efficient class E power amplifier is demonstrated for application to wireless power transfer system. The amplifier is designed with an L-type matching at the output for harmonic rejection and output matching. The power loss and the effect of each component in the amplifier with the matching circuit are analyzed with the current ratio transmitted to the output load. Inductors with a quality factor of more than 120 are used in a dc feed and the matching circuit to improve transmission efficiency. The single-ended amplifier with 20 V supply voltage shows 7.7 W output power and 90.8% power added efficiency at 6.78 MHz. The wireless power transfer (WPT) system with the amplifier shows 5.4 W transmitted power and 82.3% overall efficiency. The analysis and measurements show that high-Q inductors are required for the amplifier design to realize highly efficient WPT system.

• The KIPS Transactions:PartC
• /
• v.17C no.6
• /
• pp.471-484
• /
• 2010

In the wireless communication systems, the power consumption of a mobile device is very important issue due to its battery limitations. Hence most of the standards for wireless networks including a mobile WiMAX system are supporting their own power saving mode in way that a mobile device is able to reduce its energy usage while in the mode. However, those standards just define the arrangement of special time intervals, called a paging listening interval, during which the device needs to receive the paging-related control messages, and they do not specify how to effectively reduce the power in many different network environments. This means the amount of power spent by the device is very dependent on the implementations of individual device-vendors, and undesirable paging loss may happen according to the channel conditions. To reduce unnecessary power usage and the risk of paging loss, this paper proposes the effective frequency/BS selection algorithm applicable to a mobile device operating in the power saving mode, which serves the device with better BS based on the tracking for channel variation. This algorithm consists of the channel estimation phase during each paging listening interval, the tracking phase for the measured results, the frequency reselection phase based on the tracking activity, and the preferred BS reselection phase. Thus the proposed method can improve the paging performance while the device is moving in the network. Also the simulation result shows that the presented scheme is superior to other candidates in energy efficiency due to the channel-adaptive frequency/BS selection.

• Proceedings of the KIEE Conference
• /
• 2006.10d
• /
• pp.152-154
• /
• 2006

This paper presents an electric power control scheme in the transmission line using a UPFC(Unified Power Flow Controller). From the practical application viewpoint, the simultaneous realization of the power response desired. The author propose a new power control algorithm for UPFC. To verify the effectiveness of the proposed algorithm, a protype inverter is built and some experiments are carried out.

• The KIPS Transactions:PartA
• /
• v.16A no.5
• /
• pp.357-368
• /
• 2009

Mobile IP storage has been proposed to overcome storage limitation in the flash memory and hard disks. It provides almost capacity-free space for mobile devices over wireless IP networks. However, battery lifetime of the mobile devices is reduced rapidly because of power consumption with continuous use of a WLAN device when multimedia contents are being streamed through the mobile IP storage. This paper proposes an energy-efficient WLAN device power control technique for streaming multimedia contents with the mobile IP storage. The proposed technique consists of a prefetch buffer input/output module, a WLAN device power control module, and a reconfigurable prefetch buffer module. Besides, it adaptively determines the size of the prefetch buffer according to a quality of the multimedia contents, and it dynamically controls the power mode of the WLAN device on the basis of power on-off operations while streaming the multimedia contents. We evaluate the performance of the proposed technique on a PXA270-based mobile device that employs the embedded linux 2.6.11, Intel iSCSI reference codes, and a WLAN device. Extensive experiments reveal that the proposed technique can save the energy consumption of the WLAN device up to 8.5 times with QVGA multimedia contents, as compared with no power control.

• Journal of IKEEE
• /
• v.7 no.1 s.12
• /
• pp.1-8
• /
• 2003

In this study, the high performance BCD device structure which satisfies the high voltage and fast switching speed characteristics is devised. Through the process and device simulation, optimal process spec. & device spec. are designed. We adapt double buried layer structure, trench isolation process, n-/p-drift region formation and shallow junction technology to optimize an electrical property as mentioned above. This I.C consists of 20V level high voltage bipolar npn/pnp device, 60V level LDMOS device, a few Ampere level VDMOS, 20V level CMOS device and 5V level logic CMOS.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.1
• /
• pp.73-80
• /
• 2015

The valve device is installed in hazardous areas, such as a chemical plant explosion has been sealed with fire protection device to prevent the risk of explosion. In this paper, due to the explosion-proof devices using external power the device can not be used in infrared sensors and Zigbee sensor valve device by measuring the open degree of valve opening and closing of the danger zone to check whether. Valve opening and closing operation log screen time, we propose a low-power operation monitoring system administrators to manage and control the plant. Develop power control relay board apply an improved algorithm to apply the asynchronous LPL power management. The plant monitoring system and explosion-proof valve opening and closing the valve system with the intelligent device designed and implemented and tested it.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.323-326
• /
• 2003

In this paper, a new small size Lateral Trench Electrode Power MOSFET is proposed. This new structure, called "LTEMOSFET"(Lateral Trench Electrode Power MOSFET), is based on the conventional MOSFET. The entire electrode of LTEMOSFET is placed in trench oxide. The forward blocking voltage of the proposed LTEMOSFET is improved by 1.6 times with that of the conventional MOSFET. The forward blocking voltage of LTEMOSFET is 250V. At the same size, a increase of the forward blocking voltage of about 1.6 times relative to the conventional MOSFET is observed by using TMA-MEDICI which is used for analyzing device characteristics. Because the electrodes of the proposed device are formed in trench oxide, the electric field in the device are crowded to trench oxide. We observed that the characteristics of the proposed device was improved by using TMA-MEDICI and that the fabrication of the proposed device is possible by using TMA-TSUPREM4.