• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.8
• /
• pp.593-600
• /
• 2010

In this paper, High brightness LED (light-emitting diodes) driver IC (integrated circuit) using new current sensing circuit is proposed. This LED driver IC can provide a constant current with high current precision over a wide input voltage range. The proposed current-sensing circuit is composed of a cascode current sensor and a current comparator with only one reference voltage. This IC minimizes the voltage stress of the MOSFET (metal oxide semiconductor field effect transistor) from the maximum input voltage and has low power consumption and chip area by using simple-structured comparator and minimum bias current. To confirm the functioning and characteristics of our proposed LED driver IC, we designed a buck converter. The LED current ripple of the designed IC is in ${\pm}5%$ and a tolerance of the average LED current is lower than 2.43%. This shows much improved feature than the previous method. Also, protections for input voltage and operating temperature are designed to improve the reliability of the designed IC. Designed LED driver IC uses 1.0 ${\mu}m$ X-Fab. BiCMOS process parameters and electrical characteristics and functioning are verified by spectre (Cadence) simulation.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.2
• /
• pp.144-151
• /
• 2013

This paper presents a result of the mechanical noise and vibration analysis as well as the electrical characteristics analysis of the permanent magnet(PM) motor according to the driving method that is Brushless DC(BLDC) drive and Brushless AC(BLAC) drive. To do that, the characteristics of the PM motor, which have the same output power but different driving method, are investigated. At that time, the characteristics such as torque, torque ripple and flux density, and so on, are obtained by finite element analysis(FEA). Besides, noise and vibration are obtained by spectrum analysis. The magnetic noise is defined as noise generated from vibrations due to electromagnetic excitation force. In this paper, the electromagnetic excitation force is analyzed and design process of noise reduction is proposed. Finally, The validity of the analysis results is verified by test.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.11
• /
• pp.1550-1559
• /
• 2013

Light emitting diode(LED) lighting has been applied various industry fields because of its high efficiency, low power consumption, long life time, and environment friendly characteristics. Generally, LED lighting needs a driver to maintain constant current. Most popular driver is the switching converter. In the converter, there are several electrolytic capacitors. However the lifespan of the electrolytic capacitor is much shorter than LED. Therefore the lifespan of LED lighting with electrolytic capacitor is decreased. Also, LED lighting needs dimming control because of various needs and energy saving. This paper presents the dimmable single-stage PFC DCM flyback converter without electrolytic capacitor and parallel LC resonant filter for reducing 120[Hz] ripple on the output. The type 2 controller is used to maintain constant current and the analog dimming control is used. The proposed converter is verified through simulation and experimental works.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.139-141
• /
• 1996

The switched reluctance motors(SRM) are simple and robust in structure. Because the wide range of power and speed, their application field is increasing. In order to design the motors and to evaluate the performance of them properly, an accurate study about the analysis of motor characteristics is required. In this paper, for the analysis of SRM characteristics, the finite element method which is based on the solution of combined equations both the electromagnetic field equations and the circuit equations of stator is adopted. The analysis model is to he assumed two-dimensional and the nonlinear property of magnetic materials is considered by Newton-Raphson method. To verify the usefulness of the proposed algorithm, commercial SRM is chosen and simulated. The computed torques obtained by Maxwell Stress Tensor are compared with the experimental data and it is found that they are in good agreement. By applying the proposed algorithm to two cases, currents of stator and torques at every angular positions of rotor are obtained step by step. Comparing them, one can recognize that torque ripple of SRM can he improved by controlling the switching sequences of driving circuits.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.6
• /
• pp.2411-2418
• /
• 2017

This study focuses on the effects of using open stator slots in an interior permanent magnet traction motor with a magnetic slot wedge design in order to increase the power density at its base speed. In addition, such a configuration reduces the torque ripple under field-weakening conditions. Five different wedge models were selected, each of which was evaluated using a finite element analysis (FEA). Based on the initial model, we designed magnetic slot wedges for maximum back-EMF and minimum cogging torque. In addition, the d-q axis inductance was slightly altered due to the magnetic slot wedges. Finally, we analyzed the performance of a traction machine under field weakening control. Moreover, we have outlined the requirements for an ideal magnetic slot wedge design.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.7 no.6
• /
• pp.34-41
• /
• 1993

This paper describes an effort to develop a microcomputer-based parameter identification system for three phase and two phase brushless DC motor. Back EMF equation is derived from back EMF waveform of three phase and two phase brushless DC motor. In this paper, a new identification algorithm for the brushless DC motor parameters by Pasek's technique is de veloped. It is found that Pasek's equation is valid for the brushless DC motor, too. The results obtained clearly shows that it is possible to implement the identification system for the determination of the brushless DC motor parameters. To minimize errors due to the ripple component in the measured armature current, dlgital averaging filter is employed. The whole identification process of signal generation, measuring, parameter determination is fully automated. The use of the pmpased method in the parameter identification system shows that the averaged current curve is in excellent agreement with the estimated current curve. Therefore, this close agreement conf i i the validity of this technique.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.10
• /
• pp.1846-1857
• /
• 2011

This paper deals with design and analysis of surface-mounted PM (SPM) motor for compressor of air-conditioning system for electric vehicle applications according to slot/pole combination. First, required torque-speed curve characteristics are determined from operating conditions of the compressor. Restricted conditions such as motor size limit and current density are also determined. And then, under same rated and restricted conditions, twelve models which have different slot/pole combinations each other are designed for various pole arc/pitch ratio using simple equations and 2-d finite element (FE) analyses. Designed models are analyzed and compared in terms of back-emf THD, cogging torque, torque ripple, power losses, efficiency, etc. On the basis of analysis results, it is found that the motor with a 6-pole PM rotor and a 27-slot stator has most outstanding performances in electromagnetic aspects. Finally, through the mechanical modal analysis and demagnetization analysis, it is concluded that the determined motor is most suitable for the compressor of air-conditioning system for electric vehicles.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.4
• /
• pp.1495-1502
• /
• 2017

The Theory of operation of switched reluctance motors (SRM) depends on the reluctance torque, where energy is transferred to stator winding only. Although its construction is simple, the electrical design is complex, due to the switching configuration needed to deliver power to stator coils. However, because of the nonlinearly of magnetic circuit, SRM has torque ripple. This paper proposes a new strategy to drive SRM from a single-phase AC supply. Each stator winding is connected to AC-DC or AC-AC converters, which is called branch. All branches are connected in parallel to a single-phase AC supply. A shaft encoder allows current production in stator winding during the positive torque production region and terminates it during the negative torque production region. A magnetic flux is produced between stator poles when current is supplied from AC supply to stator coil and repeats many cycles as long as the rate of change of stator inductance is positive. Different possibilities for the configurations of AC-AC or AC-DC converters are introduced to drive SRM from the single-phase AC supply. A case study is presented for a SRM fed from AC supply through semi-controlled AC-DC converter is presented. A simulation model is introduced and verified by experimental rig for two-phase SRM.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.2 no.1
• /
• pp.53-58
• /
• 2001

The main noise sources in SMPS are divided into three parts: the switching devices, the rectifiers in secondary part, the output transformer and choke coil. In this paper we performed the noise analysis with respect to bobbin type and winding method, and designed an optimized transformer focusing on the transformer. For the comparison. we measured four parameters for each cases, including EMI conducted emission noise. signal from the switching devices, output ripple/noise voltage and leakage current. As the result, the transformer using a vertically-typed bobbin and a parallel, sandwich winding method showed the best performance. We confirmed that the SMPS developed in this research is satisfied with the IEC 601-1 international standard for the medical instrumentation. by testing its electrical characteristics and safety.

• Proceedings of the KIPE Conference
• /
• 2012.11a
• /
• pp.229-230
• /
• 2012

본 논문에서는 왜곡된 역기전력을 갖는 매입형 영구자석 동기전동기의 토크리플 저감 방법을 제안한다. 역기전력에 왜곡성분이 있는 경우 정현파 전류로 모터 제어 시 역기전력의 왜곡으로 인한 토크리플은 전동기의 진동 증대 및 효율 저하의 요인이 된다. 이러한 토크리플에 의한 전동기의 진동은 특히 저속에서 문제가 된다. 저속운전 시 전동기의 토크리플을 저감하기 위해서는 역기전력의 왜곡에 의한 토크리플을 줄일 수 있는 토크리플 보상 전류제어가 필요하다. 이 경우 토크리플 보상전류를 구하기 위해서는 역기전력의 왜곡성분에 대한 정보가 필요하다. 본 논문에서는 역기전력의 왜곡성분을 off_line 방식이 아닌 전류기반 MRAS 관측기를 사용하여 실시간으로 추정하여 토크리플 저감전류를 보상함으로써 토크리플을 저감한다. 제안된 토크리플 저감 알고리듬은 시뮬레이션을 통해 검증한다.