• ETRI Journal
• /
• v.34 no.6
• /
• pp.962-965
• /
• 2012

In this letter, we propose a new RESURF stepped oxide (RSO) process to make a semi-superjunction (semi-SJ) trench double-diffused MOSFET (TDMOS). In this new process, the thick single insulation layer ($SiO_2$) of a conventional device is replaced by a multilayered insulator ($SiO_2/SiN_x/TEOS$) to improve the process and electrical properties. To compare the electrical properties of the conventional RSO TDMOS to those of the proposed TDMOS, that is, the nitride_RSO TDMOS, simulation studies are performed using a TCAD simulator. The nitride_RSO TDMOS has superior properties compared to those of the RSO TDMOS, in terms of drain current and on-resistance, owing to a high nitride permittivity. Moreover, variations in the electrical properties of the nitride_RSO TDMOS are investigated using various devices, pitch sizes, and thicknesses of the insulator. Along with an increase of the device pitch size and the thickness of the insulator, the breakdown voltage slowly improves due to a vertical field plate effect; however, the drain current and on-resistance degenerate, owing to a shrinking of the drift width. The nitride_RSO TDMOS is successfully fabricated, and the blocking voltage and specific on-resistance are 108 V and $1.1m{\Omega}cm^2$, respectively.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.395-399
• /
• 1996

The Clamp Mode(CM) Forward Zero Voltage Switching Multi Resonant Converter(ZVS-MRC) with self-driven synchronous rectifier in studied. The loss at the synchronous rectification stage of the converter is analyzed using MOSFET linear model and is compared with the loss at the conventional schottky diode rectification stage of the converter. From the results of the analysis, it is known that the use of MOSFETs as a synchronous rectifier reduces the loss at the rectification stage over the whole load range comparing the use of schottky diodes as a conventional rectifier in the converter. In order to verify the validity of the analysis, we have built a 33W(3.3V/10A) CM Forward ZVS-MRC with self-driven synchronous rectifier, in which switching frequency is 1MHz, and tested. From the experimental results, it is known that the synchronous rectification achieved about 1W improvement in the loss at the rectification stage and about 3% in the efficiency at the converter as compared with the conventional schottky diode rectification.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.9
• /
• pp.667-670
• /
• 2010

In this paper, a high voltage current sensing circuit for boost converter is designed and verified by Cadence SPECTRE simulations. The current mirror pair, power and sensing metal-oxide semiconductor field effect transistors (MOSFETs) with size ratio of K, is used in our on-chip current sensing circuit. Very low drain voltages of the current mirror pair should be matched to give accurate current sensing, so a folded-cascode opamp with a PMOS input pair is used in our design. A high voltage high side lateral-diffused MOS transistor (LDMOST) switch is used between the current sensing circuit and power MOSFET to protect the current sensing circuit from the high output voltage. Simulation results using 0.35 ${\mu}m$ BCD process show that current sensing is accurate and the pulse frequency modulation (PFM) boost converter using the proposed current sensing circuit satisfies with the specifications.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.10
• /
• pp.2123-2135
• /
• 1997

In this paepr, we consider resistive shorts on drain-source, drain-gate, and gate-source as well as opens in MOSFETs included in typical memory cell of VLSI SRAM. Behavior of memeory is observed by analyzing voltage at storage nodes of memeory and IDDQ(quiescent power supply current) through PSPICE simulation. Using this behavioral analysis, an effective testing algorithm of complexity O(N) which can be applied to both functional testing and IDDQ testing simultaeously is proposed. Built-In Self Test(BIST) circuit which detects faults in memories and Built-In Current Sensor(BICS) which monitors the power supply bus for abnormalities in quescent current are developed and imprlemented to improve the quality and efficiency of testing. Implemented BIST and BICS circuits can detect locations of faults and defects in order to repair faulty memories.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.14-14
• /
• 2010

A high voltage current sensing circuit for LED driver IC is designed and verfied by Cadence SPECTRE simulations. The current mirror pair, power and sensing MOSFETs with size ratio of K, is used in our on-chip current sensing circuit. Very low drain voltages of the current mirror pair should be matched to give accurate current sensing, so a folded-cascode opamp with a PMOS input pair is used in our design. A high voltage high side LDMOST switch is used between the current sensing circuit and power MOSFET to protect the current sensing circuit from the high output voltage. Simulation results using 0.35um BCD process show that current sensing is accurate with properly frequency compensated opamp.

• Journal of Power Electronics
• /
• v.8 no.4
• /
• pp.363-370
• /
• 2008

In this paper, three kinds of PWM strategies for a three-phase current-fed dc/dc converter are proposed and compared in terms of losses and voltage transfer ratio. Each PWM strategy is described graphically and their switching losses are analyzed. With the proposed PWM C strategy, one turn-off switching of each bridge switch is eliminated to reduce switching losses under the same switching frequency. In addition, RMS current through the bridge switches is lowered by using parallel connection between two bridge switches and thus, conduction losses of the switches are reduced. Further, copper losses of the transformer are decreased due to the reduced RMS current of each transformer's winding. Therefore, total losses are minimized and the efficiency of the converter is improved by using the proposed PWM C strategy. Digital signal processor (DSP: TI320LF2407) and a field-programmable gate array (FPGA: EPM7128) board are used to generate PWM patterns for three-phase bridge and clamp MOSFETs. A 500W prototype converter is built and its experimental results verify the validity of the proposed PWM strategies.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.110-110
• /
• 2011

현재 전력 반도체는 신재생/대체 에너지 시스템, 자동차/전기자동차, 디스플레이/LED 드라이브 IC 등과 같이 산업용뿐만 아니라 가정용에서도 그 수요가 급증하고 있다. 이러한 전력 반도체는 각 시스템에서 전력 변환, 분배 및 관리를 하는 역할을 하게 되는데, 이러한 전력 시스템에 적용되기 위해서는 고속 스위칭, 낮은 전력 손실 및 발열, 소형화 등의 특성이 요구되어진다. 이러한 특성을 만족하기 위해 현재 전력반도체는 수평형 소자에서 수직 형태로의 구조적 변경을 꽤하고 있으며, 또한 수직형 구조에서도 더욱 소형화와 고밀도 전류, 낮은 전력 손실 특성을 구현하기 위해 여러 가지 형태의 어레이 기술을 개발하고 있다. 본 연구에서는 사각 형태의 어레이 (square array, mesh type)를 가지는 수직형 TDMOS (Trench double diffused metal oxide effect transistor)에서 트렌치 부분을 중심으로 액티브 영역과 그 외각 영역의 도핑 농도와 접합 깊이의 변화에 따른 전기적 특성 변화를 파악함으로써 TDMOS의 안정적인 구동 영역을 확보하기 위한 연구를 수행하였다. 본 연구는 silvaco 시뮬레이션 툴을 이용하여 실제 소자 제작 공정과 유사한 형태로의 공정을 가상적으로 진행하고, 액티브 영역과 그 외각 영역의 도핑 및 접합 깊이를 결정하는 이온 주입량과, 후속 열처리의 온도와 시간 등을 변화함으로써 그 전기적 특성을 상호 비교하였다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.5
• /
• pp.49-56
• /
• 2006

The bi-directional converter interfaces the low voltage battery to the inverter do link of FC generation system. When power flows from the low voltage side(battery: 48[V]) to the high voltage side(dc link: 380[V]), the circuit works in discharge mode (boost) to power the high voltage side load; otherwise, it works in charge mode (buck) to charge the low voltage side battery. In this paper, the 1.5[kW] active clamp current-fed full bridge converter employing MOSFETs is operated to discharge the battery whereas a voltage-fed half bridge converter employing IGBTs is operated to charge the battery.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.4
• /
• pp.218-221
• /
• 2015

Power MOSFETs (metal oxide semiconductor field effect transistor) operate as energy control semiconductor switches. In order to reduce energy loss of the device during switch-on state, it is essential to increase its conductance. In this study we have investigated a structure to reduce the on-resistance characteristics of the MOSFET. We have a proposed MOSFET structure of active cells region buried under the gate pad. The measurement are carried out with a EDS to analyze electrical characteristics, and the proposed MOSFET are compared with the conventional MOSFET. The result of proposed MOSFET was 1.68[${\Omega}$], showing 10% improvement compared to the conventional MOSFET at 700[V].

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.1
• /
• pp.70-77
• /
• 2005

A new converter to transfer energy from a low-voltage AC current source to a battery is proposed. It is focused to find operational modes of the converter. The low-voltage AC current source is an equivalent of the piezoelectric generator, which converts the mechanical energy to the electric energy. The converter consists of a full-bridge MOSFET rectifier and a MOSFET boost converter in order to make the converter small and efficient. The operational principle and modes of the converter are investigated with the consideration of effects of the parasitic capacitances of MOSFETs and diode. The results are proved with simulation studies using PSIM and Pspice.