• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.1
• /
• pp.71-78
• /
• 2011

In this paper, the effect of parameter errors to the estimation of the rotor angle in sensorless operation of a permanent magnet synchronous motor is analyzed. The angle error information which is utilized to estimate the rotor position can be classified into two factors, namely, the sign factor and the gain factor. This paper particularly focuses on parameter errors reflected in the sign factor of the angle error information which causes a deviation in the angle estimation. In this paper, mathematical expressions describing the deviation of the angle estimation due to the inductance error and the resistance error in the sensorless control are derived. The validity of the expression is verified by the computer simulations and the experimental results.

• Journal of Navigation and Port Research
• /
• v.27 no.2
• /
• pp.209-215
• /
• 2003

In this paper. We tested and fabricated the error amplifier for the 15 Watt linear power amplifier for the IMT-2000 baseband station. The error amplifier was comprised of subtractor for detecting intermodulation distortion, variable attenuator for control amplitude, variable phase shifter for control phase, low power amplifier and high power amplifier. This component was designed on the RO4350 substrate and integrated the aluminum case with active biasing circuit. For suppression of spurious, the through capacitance was used. The characteristics of error amplifier measured up to 45 dB gain, $\pm$0.66 dB gain flatness and -15 dB input return loss. Results of application to the 15 Watt feedforward Linear Power Amplifier, the error amplifier improved with 27 dB cancellation from 34 dBc to 61 dBc IM$_3$.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.6
• /
• pp.449-455
• /
• 2007

Position information is very important when driving the Permanent Magnet Synchronous Motor(PMSM). Generally, resolver is used to obtain exact position information. However, it generates periodic position errors due to the transformer ratio difference and excitation signal distortion. When the vector control is done with the position information that includes position error, torque ripple is generated from time to time. This paper proposes the solution through analysis of above problem. Also, it's validity is verified by simulation and experiment.

• Journal of Drive and Control
• /
• v.16 no.2
• /
• pp.72-79
• /
• 2019

Despite the development of electronic components and microprocessors, hydraulic actuators are still being applied in various applications. In some applications, there is a desire to apply a hydraulic actuator with a relatively small position error to the system. Various studies have been conducted to reduce the position error of hydraulic actuators. In this paper, the position error of the hydraulic actuator when the hydraulic oil pressure is supplied is defined as the offset generated by the servo valve, and the method for correcting the servo valve offset has been studied. A method for compensating the servo valve offset was proposed and it was verified through experiments that the position error of the hydraulic actuator was reduced. We also compared the servo valve offset correction method and controller using the PID control and disturbance observer used to reduce the position error of the hydraulic actuator. No-load test and load test were performed to confirm the performance of the servo valve offset correction method. The results of the study were compared with those obtained by using the disturbance observer and PID control.

• Proceedings of the IEEK Conference
• /
• 2000.11a
• /
• pp.345-348
• /
• 2000

In this paper, A Feedforward Linear Power Amplifier for IMT-2000 which IMD characteristics was improved was designed and fabricated. To improve the main power amplifier IMD characteristics, the Feedback loop was added to basic Feedforward Power Amplifier structure. Therefore, the output power of error amplifier can be reduced, and it is easy to control the linearization circuit to cancel total IMD. The designed power amplifier represented the 40㏈m(l0W) output power and -55㏈C 3rd IMD at Center frequency 2.14㎓ (@5㎒).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05a
• /
• pp.103-105
• /
• 2002

Instantaneous following PWM control technique is pulsed nonlinear dynamic control method. This new control technique using analog integrator is proposed to control the duty ratio D of Cuk converter. In this control method, the duty ratio of a switch is exactly equal to or proportional to the control reference in the steady state or in a transient. Proposed control method compensates power source perturbation in one switching cycle, and the average value of the dynamic reference in one switching cycle. There is no steady state error nor dynamic error between the control reference and the average value of the switched variable. Experiments with Cuk converter have demonstrated the robustness of the control method and verified theoretical prediction. The control method is very general and applicable to all type PWM.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.293-295
• /
• 2007

This paper proposes a control algorithm for the power supply to maintain the desired output voltage waveform when the instantaneous power failure occurs. The proposed system switches the control mode between the voltage-controlled and the current-controlled modes in the instantaneous power failure. The proposed control method has little steady-state error and good transient response. The validity of the proposed scheme is investigated through simulation and experimental results.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.378-381
• /
• 2002

Instantaneous following PWM control technique is pulsed nonlinear dynamic control method. This new control technique using analog integrator is proposed to control the duty ratio D of DC-DC converter. In this control method, the duty ratio of a switch is exactly equal to or proportional to the control reference in the steady state or in a transient. Proposed control method compensates power source perturbation in one switching cycle, and the average value of the dynamic reference in one switching cycle. There is no steady state error nor dynamic error between the control reference and the average value of the switched variable. Experiments with buck converter have demonstrated the robustness of the control method and verified theoretical prediction. The control method is very general and applicable to all type PWM.

• International Journal of Control, Automation, and Systems
• /
• v.3 no.spc2
• /
• pp.302-307
• /
• 2005

A novel neuro controller based simple neuro-structure with modified error function is introduced in this paper. This controller consists of two independent controllers, known as the voltage regulator and the angular controller. The voltage regulator is used to modify terminal voltage for the purpose of tracking a reference voltage. The angular controller is utilized to guarantee the stability of the system. In this structure each neuron uses a linear hard limit activation function that depends on the controlled variable and its derivatives. There is no need for parameter identification or any off-line training data. Two proposed controllers are merged by a smooth switch to build a complete controller. The effectiveness of the proposed novel control action is demonstrated through some computer simulations on a Single-Machine Infinite-Bus (SMIB) power system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.6
• /
• pp.538-548
• /
• 2014

This study provides a robust control of a grid-connected three-phase two-level photo voltaic inverter. The introduced control method uses the cascade control strategy to regulate AC-side current and DC-link voltage. A robust controller with integration action is used for the inner-loop AC-side current control, which maximizes the convergence rate using a linear matrix inequality-based optimization design method and eliminates the offset error. The robust controller design method considers the parameter uncertainty set to accommodate parameter mismatch and un-modeled components in the inverter model. An outer-loop proportional-integral controller is used to regulate DC-link voltage with linearization of DC/AC relation. The proposed control strategy is applied to a grid-connected 100 kW photo voltaic inverter.