• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.175-176
• /
• 2006

The filling property of the binder treated iron based powder made of atomized iron powder was compared with that of the one made of reduced iron powder. The latter one showed a better filling property than the former one, although the original reduced powder showed a worse flow rate. Changing the particle size distribution of the original atomized powder from wide to narrow like the original reduced iron powder, improved the filling property of the binder treated powder. As a result, the particle size distribution of the original iron powder was found to strongly affect the filling property of the binder treated powder.

• Journal of the Korean Applied Science and Technology
• /
• v.28 no.3
• /
• pp.351-358
• /
• 2011

It was researched to be alternative of TGIC type hardener with human hazard element as PT 910 mix powder paint with hardener. Generally PT 910 was compared with TGIC & Epoxy resin of hardener to be used at thermosetting powder paint. We inquired a property of matter for paint through Gel time, glass transition temperature, melting point and a property of matter for film through a property of adhesion, a property of tolerance, softness, gloss, acid-resistant, alkali-resistant, salt water spray-resistant, facilitation climatic. When PT 910 is used of hardener, it was shown the excellent results in gel time, softness, salt water spray-resistant, fracilitation climatic and the similar results in melting point, a property of tolerance, a property of adhesion, gloss, acid-resistant, alkali-resistant, as compared with the powder paint used by TGIC hardener. The glass transition temperature was little low. But there was slightly different results. After the study results, we reached the conclusion that thermosetting powder used by PT 910 is alterative to by TGIC hardener.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.501-502
• /
• 2006

The present investigation has been performed on full densification behavior and mechanical property of the powder injection molded Fe-8wt%Ni nanoalloy powder. The net shaping process of the nanopowder was conducted by powder injection molding (PIM) process. The key-process for fabricating fully densified net-shaped nanopowder by pressureless sintering is an optimal control of agglomerate size of nanopowder. Enhanced mechanical property of PIMed Fe-Ni nanopowder is explained by grain refinement and microstructural uniformity.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.11a
• /
• pp.47-48
• /
• 2014

This study is to hydration property of low carbon type recycled cement from waste cementitious powder and cement raw materials. Waste cementitious powder possible to low carbon type recycled cement in small part of additive materials. Also, low carbon type recycled cement using waste cementitious powder is suitable for low heat type cement.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.05a
• /
• pp.120-121
• /
• 2021

The organic insulation material has excellent thermal insulation property, but it is difficult to expect fire stability, and semi inorganic insulation only delays combustible hour but it is difficult to expect fire stability. In this study, thermal insulation property of cement-based non-combustible inorganic insulation using cement and non combustible materials and redispersible polymer powder was studied. As a result of the experiment, the thermal insulation property decreased as the use of redispersible polymer powder increased, but the heat insulation property improved when using the appropriate amount.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.395-396
• /
• 2006

To manufacture a flange for a compressor with a relief groove by using powder metallurgy in order to prevent deformation to the compressor in operation, powder material for the flange is charged into a mold; an ablative member having a melting point lower than that of the powder material is positioned at a place where a relief groove is to be formed; the flange is formed by compressing the powder material and the ablative member; and the formed flange is sintered at a temperature between the melting point of the powder material and the ablative member so as to melt and remove the ablative member. It made according to the new method has more excellent strength and airtight property than the conventional one. It is analyzed that the ablative member is melted and penetrated into the flange structure during the sintering process, which results in improvement of the airtight property and increase of the strength.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.89-90
• /
• 2006

Austenitic stainless steel has been used as a corrosion resistance material. However, austenitic stainless steel has poor wear resistance property due to its low hardness. In this investigation, we apply powder composite process to obtain hard layer of Stainless steel. The composite material was fabricated from planetary ball milled SUS316L stainless steel powder and WC powder and then sintered by Pulsed Current Sintering (PCS) method. We also added TiC powder as a hard particle in WC layer. Evaluations of wear properties were performed by pin-on-disk wear testing machine, and a remarkable improvement in wear resistance property was obtained.

• Journal of Powder Materials
• /
• v.9 no.3
• /
• pp.153-160
• /
• 2002

A nitrogen gas atomized aluminum powder was consolidated by powder-in sheath rolling method. A pure aluminum tube with outer diameter of 12 mm and wall thickness of 1mm was used as a sheath. The aluminum tube filled with the aluminum powder, first, was cold-rolled to the thickness of 6mm for performing, and then consolidated by the cold rolling and/or subsequent hot rolling at 360, 460 and $560^{\circ}C$. The aluminum powder compact fabricated by the sheath rolling showed high relative density more than 0.96 at any rolling conditions. The 0.2% proof stress increased with increasing hot rolling reduction and hot rolling temperature. Tensile strength was hardly affected by change in the hot rolling reduction, whereas it decreased with increasing hot rolling temperature. The powder compact showed the large elongation when cold rolling or hot rolling reduction was large. It was found that the sheath rolling was an effective method for consolidation of aluminum powder.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.144-145
• /
• 2006

A developed molybdenum hybrid-alloyed steel powder is based on a molybdenum prealloyed steel powder to which molybdenum powder particles are diffusion bonded. The sintered compact made of this powder has a finer pore structure than that of the conventional molybdenum prealloyed steel powder, because the ferritic iron phase $({\alpha}-phase)$ with a high diffusion coefficient is formed in the sintering necks where molybdenum is concentrated resulting in enhanced sintering. The rolling contact fatigue strength of the sintered and carburized compacts made of this powder improved by a factor of 3.6 compared with that of the conventional powder due to the fine pore structures.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.37 no.1
• /
• pp.29-32
• /
• 2018

Silkworm powder's thermal property is an important factor for its storage and marketing. This study examined the effect of edible enzyme on the thermal property of silkworm powder using Thermogravimetric Analysis (TGA) and Differential Scanning Calorimetry (DSC). Results of the TGA showed that regardless of the enzyme treatment, the weight loss patterns of silkworm powders exhibited 3 step thermal property deterioration at approximately $80^{\circ}C$, $280^{\circ}C$, and $480^{\circ}C$ due to water evaporation and thermal degradation. This is similar with the DSC which also resulted in all samples two endothermic peaks attributed also to water evaporation and thermal degradation. These results indicated that the use of enzyme such as protease and cellulase might not affect significantly the thermal properties of silkworm powder.