• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제17권4호
• /
• pp.365-378
• /
• 1995

Allogeneic bone grafting has recently been used in oral and maxillofacial regions to restore the cosmetic and functional problem. There are several types of allogeneic bone grafts ; bone powder, bone chips, bone blocks. Empirically, it is thought to be better to combine the allogeneic bone chips to any type of tissue adhesive not to displace during packing and condensing. But, there are no reports about using tissue adhesive in allogeneic bone grafting. This experimental study is designed to investigate the effect of the fibrin adhesive on bone healing process after demineralized allogeneic bone grafting in 60 rats. In control groups (30 rats), routine demineralized allogeneic bone grafting were done in 7 ${\times}$ 7mm calvarial bone defects which were drilled intentioally. And we used the fibrin adhesive for holding the bone particle in experimental groups (30 rats). Each experimental specimen was sacrified at 1, 2, 4, 6, 8 weeks postoperatively The results were as follows : 1. The degree of inflammatory cell infiltrations were more prominent in experimental than in control groups till 2 weeks. 2. Early fibroblast proliferation and new capillary proliferation were uncorporated around graft sites in the experimental groups later than in control groups at early stages. 3. Osteoblastic activity in control group was more prominent at 2 weeks. 4. Osteoblastic activity in experimental groups was more prominent than in control group till 4 weeks. 5. New bone formation was more in control group than experimental group till 3 weeks, but similar appearance after that time. As above results, initial bone healing within 2 weeks were more processed in without adhesive group than with adhesive group. But above 4 weeks; similar bone healing were observed.

• Progress in Superconductivity
• /
• 제5권2호
• /
• pp.124-127
• /
• 2004

Many of research efforts have been focused on the improvement of critical current density (Jc) of silver-sheathed Bi-2223 tapes far practical applications. In this study, the transformation of Bi-2212 phase was investigated, which was transformed to orthorhombic from tetragonal through pre-annealing during powder packing and drawing process. The relationship between hardness of Bi-2212 orthorhombic phase and workability of Bi-2223/Ag tape was investigated. Bi-2223 superconducting wires with 55 filaments were fabricated by stacking and drawing process with different heat-treatment histories. Before rolling process, round wires were pre-annealing at 76$0^{\circ}C$ and in a low oxygen partial pressure. We confirmed that pre-annealing step was to transform to Bi-2212 orthorhombic structure from Bi-2212 tetragonal structure and to reduce the formation of second phases. However the breakages were created at Ag-alloy clad during rolling for pre-annealed Bi-22231Ag tapes. Several pre-annealing scenarios were introduced to reduce the breakages during rolling process. Microstructure and critical current density of pre-annealed Bi-2223 superconducting tapes were investigated. We could achieve proper pre-annealing conditions for Ag-alloy clad Bi-2223 superconducting tapes.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.197-198
• /
• 2006

In the solid freeform fabrication (SFF) system using selective laser sintering (SLS), polyamide-12 powder is currently recognized as general material. In this study, some kinds of polyamide-6 powders with different shape and particlesize were fabricated to investigate the formability, the microstructure and mechanical properties. Also, to develop a more elaborate and rapid system, this study employs a new SLS device with a 3-axis dynamic focusing scanner system instead of the existing fe lens used in commercial SLS. Polyamide-6 powders having the average size of 100 m were treated thermally in order to keep the spherical symmetry in shape. These polyamide-6 powders were mixed with polyamide-12 powders having the average size of 50 m to give the bimodal distribution of size. These mixed powders showed the better fabrication in the selective laser sintering process because the smaller particles of polyamide-11 played an important role in the compact packing of powders by filling the void space between the large particles of polyamide-6. Also, Experiments have performed to evaluate the effect of a scanning path and sintering parameters by fabricating the various 3D objects.

• 멤브레인
• /
• 제22권6호
• /
• pp.415-423
• /
• 2012

탄소섬유 한외여과막 및 광촉매 혼성 수처리를 위해 관형 여과막 외부와 원통형 막 모듈 내부 사이 공간에 광촉매를 충전하였다. 광촉매는 PP (polypropylene) 구에 이산화티타늄 분말을 플라즈마 화학증착 공정으로 코팅한 것이다. 휴믹산과 카올린 모사용액을 대상으로 막오염을 최소화하기 위해 10분 주기로 10초 동안 물 역세척을 시행하였다. 기존 결과와 동일하게 휴믹산을 10 mg/L부터 2 mg/L로 변화시킴에 따라, 막오염에 의한 저항 ($R_f$)이 감소하여 2 mg/L에서 최대 총여과부피 ($V_T$)를 얻었다. 탁도와 휴믹산의 처리효율은 각각 97.1%와 74.2% 이상으로 휴믹산 농도의 영향을 받지 않았다. 그러나 기존 결과에서는 휴믹산의 농도가 증가할수록 휴믹산의 처리효율이 다소 증가하는 경향을 나타냈다.

• 한국표면공학회지
• /
• 제45권6호
• /
• pp.248-256
• /
• 2012

A Pd-based hydrogen membranes for hydrogen purification and separation need high hydrogen perm-selectivity. The surface roughness of the support is important to coat the pinholes free and thin-film membrane over it. Also, The pinholes drastically decreased the hydrogen perm-selectivity of the Pd-based composite membrane. In order to remove the pinholes, we introduced various surface pre-treatment such as alumina powder packing, nickel electro-plating and micro-polishing pre-treatment. Especially, the micro-polishing pretreatment was very effective in roughness leveling off the surface of the porous nickel support, and it almost completely plugged the pores. Fine Ni particles filled surface pinholes with could form open structure at the interface of Pd alloy coating and Ni support by their diffusion to the membrane and resintering. In this study, a $4{\mu}m$ surface pore-free Pd-Cu-Ni ternary alloy membrane on a porous nickel substrate was successfully prepared by micro-polishing, high temperature sputtering and Cu-reflow process. And $H_2$ permeation and $N_2$ leak tests showed that the Pd-Cu-Ni ternary alloy hydrogen membrane achieved both high permeability of $13.2ml{\cdot}cm^{-2}{\cdot}min^{-1}{\cdot}atm^{-1}$ permation flux and infinite selectivity.

• 한국재료학회지
• /
• 제18권5호
• /
• pp.283-288
• /
• 2008

The effect of sintering aids and glass-frit on the densification and resistivity of silver paste was investigated in an effort to enhance the sintered density and electrical conductivity of the silver electrode. To prepare Pb-free silver paste for use at low sintering temperatures, two commercial silver powders ($0.8\;{\mu}m$ and $1.6\;{\mu}m$ in size) and 5wt.% lab-synthesized nanoparticles (30-50 nm in size) as a sintering aids were mixed with 3 wt.% or 6 wt.% of glass frit ($Bi_2O_3$-based) using a solvent and three roll mills. Thick films from the silver paste were prepared by means of screen printing on an alumina substrate followed by sintering at $450^{\circ}C$ to $550^{\circ}C$ for 15 min. Silver thick films from the paste with bimodal particles showed a high packing density, high densification during sintering and low resistivity compared to films created using monomodal particles. Silver nanoparticles as a sintering aid enhanced the densification of commercial silver powder at a low sintering temperature and induced low resistivity in the silver thick film. The glass frit also enhanced the densification of the films through liquid phase sintering; however, the optimum content of glass frit is necessary to ensure that a dense microstructure and low resistivity are obtained, as excessive glass-frit can provoke low conductivity due to the interconnection of the glass phase with the high resistivity between the silver particles.

• 멤브레인
• /
• 제21권4호
• /
• pp.351-359
• /
• 2011

For advanced drinking water treatment of high turbidity water, we used the hybrid process that was composed of photocatalyst packing in space of between outside of multi-channel ceramic microfiltration membrane and membrane module inside. Photocatalyst was polypropylene (PP) beads coated $TiO_2$ powder by CVD (chemical vapor deposition) process. Instead of natural organic matters (NOM) and fine inorganic particles in natural water source, standard NOM solution was prepared with humic acid and kaolin. Water-back-flushing of 10 sec was performed per every period of 10 min to minimize membrane fouling. Resistance of membrane fouling ($R_f$) increased and J decreased as concentration of humic acid changed from 2 mg/L to 10 mg/L, and finally the highest total permeate volume ($V_T$) could be obtained at 2 mg/L. Then, treatment efficiency of turbidity and $UV_{254}$ absorbance were above 96.4% and 78.9%, respectively. As results of treatment portions by membrane filtration, photocatalyst adsorption, and photo-oxidation in (MF), (MF + $TiO_2$), (MF + $TiO_2$ + UV) processes, turbidity was treated little by photocatalyst adsorption, and photo-oxidation. However, treatment portions of $UV_{254}$ absorbance by adsorption (MF + $TiO_2$) and photo-oxidation (MF + $TiO_2$ + UV) at humic acid of 4 mg/L and 6 mg/L were above 9.0, 9.5 and 8.1, 10.9%, respectively.

• Korea-Australia Rheology Journal
• /
• 제12권1호
• /
• pp.55-67
• /
• 2000

In this paper, an experimental study of the rheological behavior of granular flow in a new type of storage silo is presented. The main characteristic of the new design is a hexagonal shape chosen with the objective of minimizing the stresses applied to the stored grains, and to reduce grain damage during the filling and emptying processes. Measurements of stress distribution and flow patterns are shown for a variety of granular materials. Because of the design of the silo, the granular material adopts its natural rest angle at all times eliminating collisional stresses and impacts between grains. A homogeneous, low friction flow is naturally achieved which provides a controlled stress distribution throughout the silo during filling and emptying. Secondary dynamic stresses, which are responsible for wall failure in conventional silos of the vertical type, are completely eliminated. A comparison between the two geometries is presented with data obtained for these silos and a number of granular materials. The discharge pattern inhibits powder formation in the silo and the filling system virtually eliminates unwanted material packing. Finally, notwithstanding the rheological advantages of this new design, the hexagonal cells that constitute the silo have many other advantages, such as the possible use of solar energy to control the humidity inside them. The cell type design allows for versatile storage capabilities and the elevation above the ground provides unlimited transportation facilities during emptying.

• 한국세라믹학회지
• /
• 제42권1호
• /
• pp.69-75
• /
• 2005

고온자전연소법에 의한 질화알루미늄 합성에 있어서, 반응물(Al) 형상과 희석제(AlN) 입도 등의 형상학적 조건이 반응생성물에 미치는 영향을 조사하였다. 평균 입경(34$\mu$m)이 같은 두 종류의 Al 분말(입상, 편상)과 평균입경이 다른 4종류의 AM분말을 희석제로 사웅하여 반응 성형체를 준비하였다. 반응성형체의 충진밀도는 이론밀도의 $35\%로 고정하였고, 초기 질소압은 $1\~10MPa$, 희석을은 $0.4\~0.7$로 변화시키면서 반응을 실시하였다. 반응물과 희석제의 입도를 비슷하게 조절함으로써, 상대적으로 질소압이 낮은 1MPa의 조건에서도 순도 $98\% 이상, 입경 수십 $\mu$m의 AlN 합성이 가능함을 확인하였다. 이러한 고순도, 고입경화는 연소파 진행 후, 성형체 내부로 질소가스 투입 용이성의 차이에 의한 현상이라고 판단된다.

• 지질공학
• /
• 제17권2호
• /
• pp.279-287
• /
• 2007

채석장으로부터 원석을 채취하여 건축석재 및 쇄석골재 등으로 가공하는 과정에서 원석의 약 60% 정도가 폐석이나 석분토로 손실되고 있다. 이 중에서 폐석의 일부만이 도로포장용 쇄석골재로 활용되고 있을 뿐 대부분의 석분토는 석재의 가공이나 파쇄공정에서 분말형태로 물에 혼입되어 슬러지탱크에 침전되게 된다. 이러한 석분토가 방류되거나 살포되면 지표나 지중의 공극들이 메워져 지표수의 지중침투, 지하수의 흐름, 공기의 소통 등이 원활하게 이루어지지 않아 생태계에 악영향을 끼칠 수도 있다. 현행 우리나라 폐기물관리법(2003)에 따르면 석분토가 사업장 내에서 발생되는 산업폐기물로 분류되고 있어 대부분을 지중에 매설하고 있는 실정이다. 따라서 석분토의 물성 및 공학특성을 개량하여 효율적 재활용방안의 수립이 필요하다. 이 연구에서는 국내 채석장에서 발생되는 석분토의 개량 및 재활용 가능성을 분석하기 위해 6개 채석장으로부터 시험용 석분토 및 원지반토를 채취한 후, 이를 일정한 비율의 배합비로 제작한 혼합토를 대상으로 여러 토질시험을 실시하였다. 시험결과를 토대로 도로용 재료로서 석분토의 개량 및 재활용 가능성을 검토하였다.