• Korean Journal of Food Science and Technology
• /
• v.19 no.2
• /
• pp.81-88
• /
• 1987

Rheological properties of rehydrated suspensions of two kinds of freeze dried Kochujang powders, processed at different freezing rates, were compared with raw Kochujang using Brookfield wide-gap rotational viscometer at $25^{\circ}C-60^{\circ}C$. Shear rates ranged from $0.1965\;sec^{-1}$ to $1.9650\;sec^{-1}$ and solid content ranged from 47% to 56%. Rehydrated suspensions of quickly frozen Kochujang powder and slowly frozen Kochujang powder, and raw Kochujang exhibited pseudoplastic behaviors with yield stress and presented thixotropic properties which followed the second-order kinetic behavior proposed by Tiu. Suspensions of Kochujang powders exhibited considerably higher decaying rates than raw Kochujang. The dependency of the equilibrium structure parameter on the shear rate was weak, and there were no significant differences among the values of structure parameters of three samples. The temperature dependency of the apparent viscosity of Kochujang suspension was fully expressed by Arrhenius equation and activation energies of suspensions of quickly frozen Kochujang powder and slowly frozen Kochujang powder, and raw Kochujang were 2.21, 2.18, and 2.32 Kcal/g.mole respectively. Consistency indices of three samples increased with solid content and decreased with temperature. Flow behavior indices of three samples showed no considerable dependency on the temperature and solid content. There were no significant differences in the rheological properties between two Kochujang powders.

• Clean Technology
• /
• v.18 no.2
• /
• pp.155-161
• /
• 2012

The purpose of this study is to remove paraffin wax binder effectively from powder injection molded part using supercritical fluids in powder injection molding process. For a thin powder injection molded part about 1-2 mm thickness, paraffin wax binder can be removed rapidly without any defect by traditional supercritical extraction process which has fixed high temperature and pressure condition. But, for a thick powder injection molded part, there are limitations in removing paraffin wax binder by the fixed high process condition because crack occurs at the beginning step. Therefore, here we studied variable condition debinding process that starts with mild process condition at the beginning step and then increase the process conditions simultaneously at each step. To find out the initial process condition that has the highest extraction yield without any defect for each sample thickness, we investigated various supercritical debinding conditions using 1-4 mm thickness ceramic injection molded sample. By using the variable condition debinding process that starts with the initial process condition at the first step and then increasing process conditions simultaneously at each step (temperature from 333.15 to 343.15 K, pressure from 12 to 27 MPa, and $CO_2$ flow rate from 1.5 to 10 L/min), over 95% of paraffin wax binder was removed from the 4 mm thick (10 mm diameter) ceramic injection molded disk samples within 5 hours.

• Elastomers and Composites
• /
• v.41 no.2
• /
• pp.97-107
• /
• 2006

The recycled polyethylene composites with various ratio of ground waste tire powder were manufactured by using a fully intermeshing co-rotating twin screw extruder for the reuse of waste tire scrap. In this investigation, the ground waste tire powders (GWTP) were blended with virgin HDPE and recycled polyethylene in the weight ratio of 0 to 50 wt.%. Mechanical properties such as tensile strength, elongation at break and impact strength were measured by using ASTM standard. The experimental results for the various composite showed that the tensile strength of composites decreased with increasing GWTP ratio, while elongation at break increased with the amounts of GWTP. On the other hand, the impact strength for the three kinds of composites showed maximum at the 30 wt.% of GWTP and then decreased. Morphology of the fracture surface tends to be rough with increasing waste tire powder content. Rheological properties were investigated by measuring the shear viscosity against shear rates and softening temperatures. They showed that melt viscosity of rubber composites in this study subsequently increased with increasing GWTP content as a result of increase of flow resistance against external stress and followed a Power-law behavior.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.4
• /
• pp.179-189
• /
• 2006

High velocity oxygen fuel(HVOF) thermal spray coating of WC-Co powder is one of the most promising candidate for the replacement of the traditional hard chrome plating and ceramics coating because of the environmental problem of the very toxic $Cr^{6+}$ known as carcinogen and the brittleness of ceramics coating. WC-Co micron and nano powder were coated by HVOF thermal spraying method for the study of durability improvement of the high speed spindle. Coatings were planned by Taguchi program for the four spray parameters of spray distance, flow rates of hydrogen, oxygen and powder feed rate. Optimal coating process was obtained by the studies of coating properties such as porosity, surface roughness, micro hardness, and micro structure. WC-Co micron and nano powder were coated on the Inconel 718 substrate by the optimal coating process obtained in this study. The wear behaviors were studied by the sliding wear tester at room temperature and at an elevated temperature of $500^{\circ}C$ for the application to high speed spindle. Sliding wear test was carried out for four most promising hard coatings of chrome coating, ceramics coatings such as $A1_2O_3,\;Cr_2O_3$ and HVOF Co-alloy T800 for the comparison of their wear behaviors. HVOF WC-Co coating was better than other coatings showing highest micro hardness of 1400 Hv and comparable friction coefficients with others. HVOF WC-Co coating is a strong candidate for the replacement of the traditional hard chrome plating for the high speed spindle.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.21 no.3
• /
• pp.652-657
• /
• 2007

This experimental study was designed to investigate the effects of FOENICULI FRUCTUS freeze dry powder (FF) on the change of cerebral hemodynamics [regional cerebral blood flow (rCBF) and mean arterial blood pressure (MABP)] in normal and further to determine the mechanism of action of FF. The results in normal rats were as follows ; FF significantly increased rCBF in a dose-dependent, but decreased MABP, This results were suggested that FF significantly increased rCBF by dilating PAD. The FF-induced increase in rCBF was significantly inhibited by pretreatment with 1H[1,2,4]oxadizolo[4,3-a]quinoxalin-1-one (ODQ, 10 ${\mu}$g/kg, i.p.), an inhibitor of guanylate cyclase and indomethacin (IDN, 1 mg/kg, i.p.), an inhibitor of cyclooxygenase and propranolol (PPN, 3 mg/kg, i.p.), a blocker of adrenalic f receptor and Lu-Nitro-L-Arginine (L-NNA, 1 m9/kB, i.p.), an inhibitor of nitric oxide synthase. The FFE-induced decrease in MABP was significantly increased by pretreatment with L-NNA and was increased by pretreatment with PPN, Dut was inhibited by pretreatment with ODQ and IDN, This results were suggested that the mechanism of FF was mediated by nitric oxide synthase and adrenalic ${\beta}$ receptor.

• Resources Recycling
• /
• v.26 no.4
• /
• pp.62-70
• /
• 2017

A cyclone type electrolytic method was used to recover silver from thiourea-hydrochloric acid mixed solutions. The electrowinning behavior of silver was investigated in different systems, such as the flow rate, current density, silver concentration, thiourea concentration and hydrochloric acid concentration. As the increase of the flow rate, current density and hydrochloric acid concentration, the recovery rate of silver was increased. Whereas, as the increase of silver concentration, the recovery rate of silver was decreased. The thiourea concentration did not affect the Ag recovery and current efficiency. Above 99% of Ag was recovered at the flow rate of 12 L/min., current density of $0.75A/dm^2$, silver concentration of 1.0 g/L, 0.5 M thiourea and 0.1 M hydrochloric acid. In most experimental conditions, silver was recovered as a powder form.

• Korean Journal of Metals and Materials
• /
• v.49 no.3
• /
• pp.221-230
• /
• 2011

The cold spray process is an emerging technology that utilizes high velocity metallic particles for surface coating. Metallic powder particles are injected into a converging-diverging de Laval nozzle and accelerated to a high velocity by a supersonic gas flow. The cold spray process normally uses a circular nozzle that has a rather narrow spraying range. To overcome this fault, a slit nozzle was considered in this study. The slit nozzle is anticipated to reduce the coating process time because it has a wider coating width than the circular nozzle. However, the slit nozzle can reduce the coating efficiency because it does not allow as much gas and particle velocity as the circular nozzle. To improve the coating efficiency of a slit nozzle, the shape of the slit nozzle was modified. And the results of gas flow and particle behaviour according to the nozzlers shape were compared by the a numerical analysis. As a results, as Expansion Ratio(ER) of 7.5 was found to be the most optimal condition for enhancing the spraying efficiency when the ER was changed by the variation of nozzle neck and exit size.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.4A
• /
• pp.767-774
• /
• 2006

This study has focused on the possibility for recycling of tailings from the sangdong tungsten mine as powder (TA) of self-compacting concrete (SCC). The experimental tests for entrapped water ratio were carried out in accordance with the specified method by Okamura. The rheological measurements of cement paste were conducted by using a commercially digital Brookfield viscometer (Model LVDV-II+) equipped with cylindrical spindles, also tests for slump-flow, time required to reach 500 mm of slump flow (sec), time required to flow through V-funnel (sec) and filling height of U-box test (mm) were carried out in accordance with the specified by the Japanese Society of Civil Engineering (JSCE). The results of this study, entrapped water ratio was decreased with increasing replacement of TA. Thickness of pseudo water film was increased, and mean plastic viscosity was decreased with increasing replacement of TA. And slump-flow of SCC was decreased with increasing replacement of TA. But time required to reach 500 mm of slump flow (sec), time required to flow through V-funnel (sec) and filling height of U-box test (mm) were satisfied a prescribed range. The mechanical properties including compressive strength, splitting tensile strength and elastic modulus were checked with the requirements specified by Korean Industrial Standard (KS). The compressive strength of SCC was decreased with increasing replacement of TA, splitting tensile strength and elastic modulus were similar to those of normal concrete.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.5
• /
• pp.1331-1335
• /
• 2010

A novel spherical carbon composite material, in which nanosized disordered carbons are dispersed in a soft carbon matrix, has been prepared and investigated for use as a potential anode material for lithium ion batteries. Disordered carbons were synthesized by ball milling natural graphite in air. The composite was prepared by mixing the ball-milled graphite with petroleum pitch powder, pelletizing the mixture, and pyrolyzing the pellets at $1200^{\circ}C$ in an argon flow. The ballmilled graphite consists of distorted nanocrystallites and amorphous phases. In the composite particle, nanosized flakes are uniformly distributed in a soft carbon matrix, as revealed by X-ray diffractometer (XRD) and transmission electron microscopy (TEM) experiments. The composite is compatible with a pure propylene carbonate (PC) electrolyte and shows high rate capability and excellent cycling performance. The electrochemical properties are comparable to those of hard carbon.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.425-430
• /
• 2002

The needs of the times, a cement plays an important roll in the materials field. So, in this research we would like to study on the properties of Photocatalytic Cement for waste gas reduction. The fundamental phenomena of the Photocatalytic Cement were observed by the NOx Analyzer, Bonding strength, SEM, Flow and Surface hardness(Pencil tester). As a result of this study, the Photocatalytic Cement used Photocatalytic powder, admixture and other materials can obtain its physical properties, also photocatalytic efficiency. If we have added a various experiment, we could have to develop the Photocatalytic Cement.