• 한국지반신소재학회논문집
• /
• 제8권1호
• /
• pp.11-18
• /
• 2009

본 논문에서는 보강토사면 안정해석에 있어서 한계 평형법과 강도감소법에 의한 유한요소법의 비교분석결과를 나타내었다. 현재 보강토 옹벽 해석에 적용하는 방법은 한계평형해석법이다. 강도감소법에 의한 유한요소법은 연속체 역학 기반을 두고, 흙의 강도정수를 안전율로 나누어 감소시켜, 수렴되지 않는 시점을 사면의 파괴로 간주하는 방법이다. 본 연구에서는 보강토옹벽사면의 안전율과 파괴활동면에 대하여 비교검토를 하였다. $60^{\circ}$ 보강토 사면에 대하여 LEM과 SSR-FEM 방법에 의한 안정성해석결과에 대하여 비교검토하였다. 두 해석에 의한 비교 검토결과 보강토 옹벽의 안정성 해석에 대하여 SSR-FEM의 유효성이 조사되었다.

• Advances in aircraft and spacecraft science
• /
• 제4권5호
• /
• pp.515-528
• /
• 2017

Since composite structures are widely used in structural engineering, delamination in such structures is an important issue of research. Delamination is one of a principal cause of failure in composites. In This study the electrical potential (EP) technique is applied to detect and locate delamination in basalt fiber reinforced polymer (FRP) laminate composite pipe by using electrical capacitance sensor (ECS). The proposed EP method is able to identify and localize hidden delamination inside composite layers without overlapping with other method data accumulated to achieve an overall identification of the delamination location/size in a composite, with high accuracy, easy and low-cost. Twelve electrodes are mounted on the outer surface of the pipe. Afterwards, the delamination is introduced into between the three layers (0º/90º/0º)s laminates pipe, split into twelve scenarios. The dielectric properties change in basalt FRP pipe is measured before and after delamination occurred using arrays of electrical contacts and the variation in capacitance values, capacitance change and node potential distribution are analyzed. Using these changes in electrical potential due to delamination, a finite element simulation model for delamination location/size detection is generated by ANSYS and MATLAB, which are combined to simulate sensor characteristic. Response surfaces method (RSM) are adopted as a tool for solving inverse problems to estimate delamination location/size from the measured electrical potential changes of all segments between electrodes. The results show good convergence between the finite element model (FEM) and estimated results. Also the results indicate that the proposed method successfully assesses the delamination location/size for basalt FRP laminate composite pipes. The illustrated results are in excellent agreement with the experimental results available in the literature, thus validating the accuracy and reliability of the proposed technique.

• Corrosion Science and Technology
• /
• 제18권6호
• /
• pp.277-284
• /
• 2019

External corrosion control of buried pipe can be achieved by the combination of barrier coating and cathodic protection. Coating damage and deterioration can be induced by many reasons; damage during handling and laying, enhanced failure at low temperatures, failure during commissioning and operation, disbanding due to inadequate surface cleaning, rock penetration during installation and service etc. This work focused on the effect of survey conditions on the reliability of coating flaw detection of buried pipes. The effects of applied voltage and anode location on the detection reliability of coating flaw of buried pipe in soil with the resistivity of ca. 25.8 kΩ·cm were discussed. Higher applied voltage increased the detection reliability, regardless of buried depth, but deeper burial depth reduced the reliability. The location of the anode has influenced on the detection reliability. This behaviour may be induced by the variation of current distribution by the applied voltage and buried depth. From the relationship between the applied voltage and reliability, the needed detection potential to get a desire detection reliability can be calculated to get 100% detection reliability using the derived equation.

• 한국안전학회지
• /
• 제28권2호
• /
• pp.21-25
• /
• 2013

The purpose of this study is to provide basic data for the safety assessment of a water purifier when water leaks due to inappropriate maintenance and the examination of the cause of accidents related to the leak. Due to its inspection and management by non-specialists, if a leak occurs in a water purifier with the water level controller being inclined, it may result in the failure of the compressor, power supply line, PCB, etc. The analysis of the thermal diffusion pattern of water purifier compressors using a thermal image camera shows that its maximum temperature was approximately $80^{\circ}C$. In addition, its operating current was a maximum of 13 A and the system's operating current was approximately 1.7 A after the compressor was charged. It was found that the housing type power cable cover of the compressor had the effect of preventing electric shock but has poor flame resistance. Furthermore, the performance of the overload protector, PTC relays, etc., was excellent but they have potential for problems as metallic terminals were exposed, resulting in the potential of a safety related accident. The terminals and their surface damaged by the tracking showed a trace of carbonization and the resistance between terminals was measured to be approximately $8{\Omega}$. In addition, while the tracking was proceeding, the fuse and circuit breaker installed for system protection did not operate.

• 구강회복응용과학지
• /
• 제31권4호
• /
• pp.340-348
• /
• 2015

임플란트주위염(peri-implantitis)은 기능중인 골유착 임플란트 주위의 조직에서 생기는 사이트 별 감염성 질환이며 임플란트 후기 실패(late failure)의 원인으로 가장 높은 비율을 차지한다. 여러 연구들을 통해 미생물 침착이 임플란트주위염에 미치는 영향이 보고된 바 있으며 세균막의 제거는 임플란트주위염의 치료 시 필수조건이 된다. 최근에 여러 연구들을 통해 티타늄 임플란트에 레이저를 사용하여 표면을 살균, 정화 시키는 방법에 대한 실험이 많이 보고되고 있다. 본 논문에서는 임플란트주위염 처치에 있어 레이저가 갖는 효능에 대한 최근 연구 결과들을 문헌고찰을 통해 되짚어보고자 한다.

• 비파괴검사학회지
• /
• 제33권2호
• /
• pp.205-211
• /
• 2013

초음파 감쇠를 이용하여 티타늄 용접부에 대해 기계적 특성, 파단면 및 초음파특성을 연구하였다. 준비된 티타늄 시험편은 아르곤 가스를 이용하여 제작하였다. 티타늄 용접 시험편이 파단 되었을 때 변화하는 초음파 신호변화를 확인하기 위해서 인장시험을 실시하였다. 주사전자현미경을 이용하여 파단면을 관찰하고, 4 MHz 수직 탐촉자를 이용하여 초음파 시계열 신호를 획득하였다. 티타늄 판재에서 용접부는 모재부와 열영향부에 비하여 기계적 특성이 떨어지며 파단면분석을 통해 용접부의 입자크기가 모재부보다 큼을 확인할 수 있었다. RMS 신호 처리한 초음파 포락선의 면적과 인장강도의 상관관계를 나타내었다. 따라서 초음파를 이용하여 티타늄 용접부의 건전성 평가 방법이 유용함을 알 수 있었다.

• 한국측량학회:학술대회논문집
• /
• 한국측량학회 2006년도 춘계학술발표회 논문집
• /
• pp.541-546
• /
• 2006

Recently, slope failures are happen to natural disastrous when they occur in mountainous areas adjoining highways in Korea. The accidents associated with slope failures have increased due to rapid urbanization of mountainous areas. Therefore, Regular maintenance is essential for all slope and needs maintenance of road safety as well as road function. The purpose of this paper is to recommend a standard of a $N_{10}^{\sim}$ value of Distribution of a potential failure layer using PPT(Portable penetration test).

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 지반공학 공동 학술발표회
• /
• pp.689-697
• /
• 2005

The soil nailing system at permanent slope reinforcement is used with various facing methods in Korea. Also, pressure-injected grout technique is variously applied to many structures. However, most design of the pressure-injected grout technique have been carried out empirically because of complicated mechanisms associated with the behavior of surrounding soils and the hardening process of cement grout. Therefore this study, a newly modified soil nailing technology named as the PGSN (Pressure Grouting Soil Nailing) system with fabric form is developed to increase the global stability. Up to now, the PGSN system has been estimated mainly focusing on an establishment of the design procedure. In the present study, numerical study are carried out to evaluate potential failure surface and minimum factor of safety including facing stiffness and expanded radius of cemented grout by SSR (Shear Strength Reduction) technique. Also, results of numerical analysis are carried out for the typical section of soil nails slope using $FLAC^{2D}$ program for expanded effective radius by pressure grouting.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.964-968
• /
• 2008

Infrared thermography using high-speed infrared camera has been recognized as a powerful method for various potential applications, such as nondestructive inspection, failure analysis, stress analysis, and medical fields, due to non-contact, high-speed, and high spatial resolution at various temperature ranges. In this investigation, damage evolution due to generation of hot spots on railway brake disc was investigated using the infrared thermography method. A high-speed infrared camera was used to measure the surface temperature of brake disc as well as for in-situ monitoring of hot spot evolution. From the thermographic images, the observed hot spots and thermal damage of railway brake disc during braking operation were qualitatively analyzed. Moreover, in this investigation, the previous experimental and theoretical studies on hot spots phenomenon were reviewed, and the current experimental results were introduced and compared with theoretical prediction.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 가을 학술발표회 논문집
• /
• pp.301-313
• /
• 2001

Reinforced earth is a composite construction material in which the strength of engineering fill is enhanced by the addition of strong tensile reinforcement in variable types. The basic mechanism of reinforced earth involves the generation of frictional forces and bearing resistances between the soil and the reinforcement. The primitive structure of reinforced earth in Korean peninsula were found as the earth wall built around the old fort In about 3rd century Modern reinforced earth was introduced to Korea early 1980, and spreaded tremendously through the nation. Among them, not a few reinforced earth walls which were built ignored over all stabilities have been collapsed. In this paper basic concepts, economic benefits, design considerations and future applicable trends of reinforced earth are reviewed in simple manners.