• Journal of Radiation Industry
• /
• v.11 no.3
• /
• pp.157-165
• /
• 2017

In this paper, we calculate the light photons collection efficiency of large-volume plastic scintillation detector mainly used for radiation portal monitor (RPM). A Monte Carlo light photon transport code, DETECT2000, were used to quantitatively evaluate light collection efficiency of plastic scintillation detector. DETECT2000 calculated the placement of light collection efficiency based on the energy spectrum. We calculated the light collection efficiency relative to the position of the energy spectrum that proportional to the placement of the source. The $850{\times}285{\times}65mm^3$ size of polyvinyl toluene (PVT) scintillator was used for measurements. Through DETECT2000 simulation, the light collection efficiency of $5{\times}5$ arrays were calculated and verification was performed by comparing with experimentally measured. And then, the corrected MCNP simulation by applying the light collection efficiency in $21{\times}13$ arrays was compared and analyzed. Comparing the Monte Carlo simulation with measured results, it shows an average difference of 10.1% in $5{\times}5$ arrays. Particularly, about twice of the difference was found in the edge of first column, which coupled with PMT. In whole $5{\times}5$ array, the overall ratio was the same except for the first column. And then comparing the energy spectra of the $21{\times}13$ array with and without the light collection efficiency, it shows a difference of 6.69% in Compton edge area. The DETECT2000 based light collection efficiency simulation showed well agreement with the point source experiment. And comparing with measured energy spectra, we could compare the differences according to whether or not the light collection efficiency was applied. As a results, it is possible to increase the accuracy and reliability of Monte Carlo simulation results by pre-calculating the light collection efficiency according to the PVT geometry by using the DETECT2000.

• Journal of the Korean Society of Safety
• /
• v.34 no.5
• /
• pp.7-14
• /
• 2019

The type III vessel, which is used to store high-pressure hydrogen gas, is made by wrapping the vessel's liner with carbon fiber composite materials for strength performance and lightening. The liner seals the internal gas and the composite resists the internal pressure. The properties of the fiber composite material depends on the angle and thickness of the fiber. Thus, engineers should consider these various design variables. However, it significantly increases the design cost due to the trial and error under designing based on experience or experiments. And, for aluminum liners, fatigue loads due to using and charging could give a huge impact on the performance of the structure. However, fatigue failure does not necessarily occur in the position under the highest load in use. Therefore, for hydrogen storage vessel, fatigue evaluation according to design patterns is essential because stress distribution varies depend on composite layer patterns. This study performed an optimization analysis and evaluated a high-pressure hydrogen storage vessel to minimize these trial and error and improve the reliability of the structure, while simultaneously conducting fatigue assessment of all patterns derived from the optimization analysis process. The results of this study are thought to be useful in the strength improvement and life design of composite reinforced high-pressure storage vessels.

• Journal of the Korean Society for Railway
• /
• v.10 no.5
• /
• pp.589-595
• /
• 2007

Korea Railroad Research Institute has developed the driverless rubber-tired K-AGT (Korean-Automated Guideway Transit) system from 1999 to 2005 and has done its performance and reliability tests on the test line at Gyeongsan-city. Radio Frequency Communication-Based Train Control system of K-AGT, which employed Advanced Automated Train Control scheme, detects train position using the radio propagation delay between wayside and vehicle radio equipment. In this paper, we investigate whether the transmission power of radio system can be reduced to the permitted level announced by the Ministry of Information and Communication for license-free ISM(Industrial Scientific Medical) frequency bands. We first determine radio propagation model, using the measured data at test line, and perform simulation for radio coverage prediction. From the simulation results, we identify that the radio system operated with reduced power can provide good link quality in total test line.

• Journal of the Korea Society of Computer and Information
• /
• v.26 no.7
• /
• pp.19-27
• /
• 2021

In this paper, we propose a method for detecting characters in images and detecting facial regions, which consists of two tasks. First, we separate two different characters to detect the face position of the characters in the frame. For fast detection, we use You Only Look Once (YOLO), which finds faces in the image in real time, to extract the location of the face and mark them as object detection boxes. Second, we present three image processing methods to detect accurate face area based on object detection boxes. Each method uses HSV values extracted from the region estimated by the detection figure to detect the face region of the characters, and changes the size and shape of the detection figure to compare the accuracy of each method. Each face detection method is compared and analyzed with comparative data and image processing data for reliability verification. As a result, we achieved the highest accuracy of 87% when using the split rectangular method among circular, rectangular, and split rectangular methods.

• Convergence Security Journal
• /
• v.17 no.5
• /
• pp.87-92
• /
• 2017

MANET is a network composed itself because mobile nodes are connected wirelessly. It has been applied to various fields for group communication. However, the dynamic topology by the movement of the nodes causes routing failure frequently because it is difficult to maintain the position information of the nodes participating in the group communication. Also, it has a problem that network performance is decreased due to high overhead for managing information of member nodes. In this paper, we propose a multicast technique using location-based 2-tier virtual group that is flexible and reliable in management of member nodes. The network is composed of cellular zones and the virtual group is constructed using the location information of the nodes in the proposed technique. The virtual group management node is selected to minimize the overhead of location information management for member nodes in the virtual group. In order to improve the reliability for management of member nodes and multicast data transmission, it excludes the gateway node with low transfer rate when setting the route after the packet transmission rate of the member nodes is measured. The excellent performance of the proposed technique can be confirmed through comparative experiments with AMroute method and PAST-DM method.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.7
• /
• pp.448-466
• /
• 2019

Today, companies are increasingly focused on SCM (Supply Chain Management) as a means for cost-cutting and efficient operation. The company's ultimate objective is to win and maintain a sustained dominant position in the uncertainties of the global environment and future competitiveness. In this respect, this study examined the effects of management strategy, collaboration process and SCM integration on corporate performance in small and midsize parts manufacturers. The results of empirical analysis are summarized as follows. Management strategy, collaboration process and SCM integration had positive effects on corporate performance in domestic small and midsize parts manufacturers, and all hypotheses were supported. Consequently, it can be confirmed that quality, cost and flexibility for management strategy, and strategic objective perception, support policy, problem solution and knowledge information sharing for delivery and collaboration as small and midsize parts manufacturers are mechanisms for improving quality reliability, decreasing cost, delivery obedience and information system operation of SCM integration, and boosting corporate quantitative and qualitative performance.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.2
• /
• pp.120-126
• /
• 2019

Recently, there is an increasing need for highly precise processing with the rapid development of precision machinery, electrical and electronics, and semiconductor industries. Cutting machine control relies on the operator's sense and experience in tradition, but it has been greatly enhanced by the adoption of CNC(Computerized Numeric Controller). In addition, cutting dynamics technology has been paid attention to reflect the operating state of machine in real time. This paper presents a method to detect and stabilize tool vibration by attaching an acoustic sensor to a CNC machine. The sensed acoustic data is synchronized with the tool position and the abnormal vibration frequency is separated from the collected acoustic frequency, then analyzed to detect the tool vibration. Also the reliability the tool vibration detection and stabilization is improved by applying the cutting dynamic method. The proposed method is analyzed and evaluated in terms of the surface roughness.

• Journal of the Korea Society of Computer and Information
• /
• v.24 no.4
• /
• pp.169-176
• /
• 2019

Wireless sensor networks are used to monitor and control areas in a variety of military and civilian areas such as battlefield surveillance, intrusion detection, disaster recovery, biological detection, and environmental monitoring. Since the sensor nodes are randomly placed in the area of interest, separation of the sensor network area may occur due to environmental obstacles or a sensor may not exist in some areas. Also, in the situation where the sensor node is placed in a non-relocatable place, some node may exhaust energy or physical hole of the sensor node may cause coverage hole. Coverage holes can affect the performance of the entire sensor network, such as reducing data reliability, changing network topologies, disconnecting data links, and degrading transmission load. It is possible to solve the problem that occurs in the coverage hole by finding a coverage hole in the sensor network and further arranging a new sensor node in the detected coverage hole. The existing coverage hole detection technique is based on the location of the sensor node, but it is inefficient to mount the GPS on the sensor node having limited resources, and performing other location information processing causes a lot of message transmission overhead. In this paper, we propose an Adjacent Matrix-based Hole Coverage Discovery(AMHCD) scheme based on connectivity of neighboring nodes. The method searches for whether the connectivity of the neighboring nodes constitutes a closed shape based on the adjacent matrix, and determines whether the node is an internal node or a boundary node. Therefore, the message overhead for the location information strokes does not occur and can be applied irrespective of the position information error.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.5
• /
• pp.326-334
• /
• 2019

Development of Small UAV using HILS (Hardware In the Loop Simulation) can be effectively used to improve the reliability of UAV (Unmanned Aerial Vehicle) while reducing cost and time. It is also possible to reduce the damage to people or property by simulating the malfunction of the Flight Control Computer (FCC) that may occur during the actual flight. For applying such HILS, a real-time simulation environment capable of providing an environment similar to an actual flight condition is required. In this paper, we constructed a real - time HILS environment for Small UAV using 6 D.O.F motion table. In order to link the 6 D.O.F motion table developed in the previous research with the HILS environment in real time, the motion algorithm was changed from the position control method to the velocity control method. Also, we implemented modeling of inverse kinematics model for command transmission in Matlab $Simulink^{(R)}$ and verified the action of motion table according to the simulation model.

• Journal of Biomedical Engineering Research
• /
• v.43 no.3
• /
• pp.177-184
• /
• 2022

The purpose of this study was to present the IMU sensor based trunk stabilization exercise and to evaluate the changes in the muscle activity and thickness with non-specific low back pain patients (N=30). They were classified into two groups; lumbar stabilization exercise using IMU sensor (ILS), (n₁=20) and general lumbar stabilization exercise (GLS), (n₂=10). By comparing the difference between pre and post intervention via trunk muscle activity and muscle thickness, the significant differences were identified. Muscle activity was measured on external oblique (EO), internal oblique (IO), and multifidus (MF) by using surface electromyography (sEMG). Muslce thickness was measured on external oblique, internal oblique, transverse abdominis (TrA), and multifidus (MF) by using ultrasonography. sEMG activity was recorded at right side-bridge position. Each group performed the proposed lumbar stabilization exercise for 30 minutes a day, 5 times a week for 4 weeks. Trunk muscle activity was observed with a significant increase in the IO of ILS (p<.05) and a decrease in the MF of GLS (p<.05). Trunk muscle thickness was significantly increased in left EO and both IO of GLS (p<.05), and also significant increased right EO, both IO, both TrA, and both MF of the ILS (p<.05). In the future, a convergence approach of rehabilitation and engineering is needed to select a sensor suitable for rehabilitation purposes, study the validity and reliability of data, and produce appropriate rehabilitation contents.