• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.59 no.2
• /
• pp.135-140
• /
• 2010

This paper presents a sensorless speed control of BLDC Motor using terminal voltage of the one phase. Rotor position information is extracted by indirectly sensing the back EMF from only one of the three terminal voltages for a three-phase BLDC motor. Depending on the terminal voltage sensing rotor position, active filter is used for position information. This leads to a significant reduction in the component device of the sensorless circuit. Therefore this is a advantage for the cost saving and size reduction. With indirect sensing methods based on detection of the terminal voltage that require active filtering, the position information needs the six divider section by PLL circuit, the binary counter and johnson counter by the EPLD. Finally, this algorithm can estimate the rotor position information similar to Hall-sensor sticked the three-phase BLDC motor. As a result, the method described that it is not sensitive to filtering delays, allowing the motor to achieve a good performance over a wide speed range. In addition, a simple starting method and a speed estimation approach are also proposed. Experimental and simulation results are included to verify the proposed scheme.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.8
• /
• pp.157-164
• /
• 2000

This paper presents a method to detect a rotor position and to drive a BLDC motor from standstill to medium speed without any position sensor comparing the current responses due to the inductance variation in the rotor position. A rotor position at a standstill is identified by the current responses of six pulses injected to each phase of a motor. Once the motor stars up pulse train that is composed of long and short pulses is injected to the phase corresponding to produce the maximum torque and the next phase continuously. it provides not only the torque but also the information of the next commutation time effectively when the response of long and short pulses crosses each other after the same time delay. This method which is verified experimentally using a DSP can drive a BLDC motor to the medium speed smoothly without any rattling and time delay compared with the conventional sensorless algorithm.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.201-210
• /
• 2018

This paper proposes a new start-up method for a load commutated inverter (LCI) in a large synchronous gas-turbine generator. The initial rotor position for start-up torque is detected by the proposed initial angle detector, which consists of an integrator and a phase-locked loop. The initial rotor position is accurately detected within 150ms, and the angle difference between the real position and the detected position is less than 1%. The LCI system operates in two modes (forced commutation mode and natural commutation mode) according to operating speed range. The proposed controllers include a forced commutation controller for the low-speed range, a PI speed controller and a PI current controller, where the forced commutation controller is connected to the current controller in parallel. The current controller is modeled by Matlab/Simulink, where a six-pulse delay of the thyristor and a processing delay are considered by using a zero-order hold. The performance of the proposed start-up method is evaluated in Matlab/Psim at standstill and at low speed. To verify the feasibility of the method, a 5kVA LCI system prototype is implemented, and the proposed initial angle detector and the system performance are confirmed by experimental results from standstill to 900rpm.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.660-664
• /
• 2004

The indirect rotor position detection method using terminal voltage of brushless DC motor (BLDCM) requires simple control circuit, and has wide speed range of sensorless operation. However, because the substantial phase difference exists between real back emf and terminal voltage, the existing indirect detection method using analog filter which is affected by frequency, speed, and load sensitively cannot be synchronized with current, in the end, it advances or delays. This paper presents new analog filter circuit design for rotor position estimation in order to solve the problem, and proposes novel sensorless operation method which is stable even in high speed range and not influenced by parameters with analysis on phase difference by load and speed. Moreover, the appropriateness of the proposed sensorless drive in this paper is verified and analyzed by experimentation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.1
• /
• pp.16-23
• /
• 2018

PM synchronous motor may be rotated to an arbitrary direction and speed by outside wind under natural condition in cases where the fan is applied outside, such as in vehicle radiators and outdoor air-conditioners. Sensorless controls that cannot detect rotor position requires additional sensorless control algorithm because a rotor is rotated by an external load. In this study, the sensorless control of a PM synchronous motor under naturally rotating condition is proposed. The natural rotation conditions are classified as forward high-speed rotation, reverse high-speed rotation, and low-speed rotation. Experiment results verify the performance of the sensorless control, including the rotor speed and position detection at natural rotation mode and switch to the closed-loop sensorless control.

• Journal of Mechanical Science and Technology
• /
• v.14 no.7
• /
• pp.722-729
• /
• 2000

The goal of this paper is to describe an advanced method of a crack detection: a new way to localize position and to estimate depth of a crack on rotating shaft. As a first step, the shaft is physically modelled with a finite element method and the dynamic mathematical model is derived using the Hamilton principle; thus, the system is represented by various subsystems. The equations of motion of the shaft with a crack are established by adapting the local stiffness change through breathing and gaping from the crack to an undamaged shaft. This is the reference system for the given system. Based on a model for transient behavior induced from vibration measured at the bearings, a nonlinear state observer is designed to detect cracks on the shaft. This is the elementary NL-observer (Beo). Using the observer, an Estimator (Observer Bank) is established and arranged at the certain position on the shaft. When a crack position is localized, the procedure for estimating of the depth is engaged.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.3
• /
• pp.205-210
• /
• 2013

This paper presents a novel hall sensor fault detection and fault-tolerant control method for a high-speed permanent magnet synchronous motor (PMSM) drive system. A phase locked loop (PLL) type position estimator is used with a conventional interpolation based rotor position estimator to reduce position errors due to misalignment of hall sensors. The expected trigger time of hall sensor's output is used for detecting hall sensor fault condition and the PLL type position estimator is reconfigured for fault-tolerant control at the hall sensor fault condition. The proposed method can minimize current ripples during the transition from sensored control using hall sensors to sensorless control. Experimental results have been proposed to prove the validity of the proposed method.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.434-438
• /
• 2000

In this paper the low cost sensorless control circuit for a PM synchronous motor without the mechanical rotor position sensors is presented. The sensorless control algorithm and position detection circuit for the sinusoidal current wave drive is more complex than that of the rectangular current wave drive. The proposed position sensing circuit is composed of an operational amplifier and several passive elements. The design procedures for getting the optimal parameters for the position sensing circuit are presented. The performance of the proposed algorithm is verified through the simulations and experiments.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.2
• /
• pp.114-121
• /
• 2013

High efficiency operation is required for motors of vehicle to increase fuel efficiency due to the regulation of exhaust gas. This paper presents a control method of fuel pressure to increase fuel efficiency and a sensorless control method of BLDC motor to get higher efficiency than conventional brushed DC motor. Initial rotor position of BLDC motor is detected from current value that is occurred by test voltage pulse and rotor is accelerated by defined sequence to enter sensorless operation mode. The algorithm to control flow rate of fuel pump uses PI controller that is control motor speed to maintain the target fuel pressure commanded by ECU.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1612-1617
• /
• 2004

Unbalance analysis is essential in the rotor system. However, some problems still remain in the aspects of computational efficiency and accuracy. In the present paper a new method is proposed for estimating the mass unbalance of a rotating shaft by using the vibration signals. This is an advanced new method for the detection of a mass unbalance and its phase position. Based on the signal processing with FFT, an estimator is designed to detect the mass of unbalance. And an improved Lissajous diagram is also introduced with statistical analysis, which make it possible to compute the phase position of the mass unbalance efficiently and arranged at a certain location of the shaft. The proposed method is demonstrated and validated through several test examples.