• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.83-89
• /
• 2000

This paper presents a dynamic modeling and a sliding mode controller for the high-speed / high-accuracy position control system. Selected target system is the wire bonder head assembly which is used in semiconductor assembly process. This system is a reciprocating one around the pivot point that consists of VCM(voice coil motor) as a actuator and transducer horn as a bonding tool. For the modeling elements, the system is divided into electrical circuit, magnetic circuit and mechanical system. Each system is modeled by using the bond graph method and united into the full system. Two major aims are considered in the design of the controller. The first one is that the horn must track the given reference trajectory. The second one is that the controller must be realizable by using the DSP board. Computer simulation and experimental results show that the designed sliding mode controller provides better performance than the PID controller.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.1215-1217
• /
• 1992

This Paper described the hish performance position control for elevator using induction motor and driver. In this paper, the suitable Motor specifications for elevator drive are briefly discussed and high accuracy position control for both kinds of control method is analysed considering the parameter variation in the primary and secondary resistances. Since the pre-identified values of the motor constants are used to determine the control inputs, the performance degradation is caused by the parameter variation such as in the motor resistance. Particularly, the value of secondary resistance is considered significant because the control gain to determine the slip frequency is heavily dependent on that. The new proposed method uses on special small input signal for the parameter indentification and is expected to have the high accuracy position.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.6
• /
• pp.518-522
• /
• 2001

The main problem of the calibration of robots is to measure the position and orientation of a robot end effector. The calibration methods can be used as tool to improve the accuracy of robots without change of the arm or control architecture or robots. But such calibration methods require accurate measurements. Dynamic measurement of position and orientation provides a solution for this problem and improves dynamic accuracy by dynamic calibration of robots. This paper describes the development of the laser tracking system capable of determining the static and dynamic performance of industrial robots. The structure and systems components are presented and basic experimental results are included to demonstrated the instrument performance. The system can be applied to the remote controlled mobile robots as well s the calibration of robots.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1484-1487
• /
• 1996

An Automatic coking control system was developed to achieved substantial energy and labor savings through the stabilization and optimization of coke oven operation. With the aim of saving energy and labor, the coke department has been advanced automation and systematization. A typical examples of automation is Center Position Control System(CPCS) for coke oven. This system is proved effective in improvement of center position accuracy.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.53 no.1
• /
• pp.50-54
• /
• 2004

Reference trajectory generation plays a key role in the computer control for accurate position control of machine. Generated trajectories must not only describe the desired tool path accurately, but must also have smooth kinetic profiles in order to maintain higher tracking accuracy, and to avoid exciting the natural modes of the mechanical servo control system. To achieve higher accurate position control, a method of limiting accelerating and decelerating speed data of reference trajectories is proposed to draw the path with an assigned accuracy without any complex operations.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1858-1862
• /
• 2005

Stepping motor normally operates without feedback and may loss the synchronization. This problem can be prevented by using positional feedback. This paper introduces one method for closed loop control of stepping motor and a method for combining full-step control and micro-step control. This combination controlling apparatus can perform position control with high accuracy in a high speed, so that it will not suffer from vibration (or hunting) problem when stopping motor. Controlling apparatus contains a position counter block for detecting rotor position of stepping motor, a driving block for supplying current to windings of stepping motor, a control block for comparing output signal of position counter block with command position (desired position) and outputting current command signal based on deviation between current position and command position of rotor. To output current command signal, the control block refers to a sine wave data table. This table contains value of duty cycle of Pulse Width Modulation signal. As the second object of this paper, the process of building this data table is also presented.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.1
• /
• pp.16-25
• /
• 1997

This paper shows the development of the high accuracy vehicle positioning algorithm using the differential technique in vehicle tracking systems form the existing vehicle position which is acquired from the global positioning system (GPS). The control center receives the satellite ephemerise data and pseudorange correction from the reference station, and vehicle position from the moving vehicle. The pseudorange is calculated with the satellite position and the vehicle position, and corrected by pseudorange correction. Using this corrected pseudorange and kalman filter, more improved vehicle positioning data were obtained.

• Journal of Astronomy and Space Sciences
• /
• v.40 no.3
• /
• pp.113-122
• /
• 2023

Although the Relative Global Navigation Satellite System (GNSS) positioning technique provides high accuracy, it has several drawbacks. The scarcity of control points, the long baselines, and using of ultra-rabid and rabid products increased position errors. This study has designed a New MATLAB Program that helps users automatically select suitable IGS stations related to the baseline lengths and the azimuth between GNSS points and IGS stations. This study presented criteria for the length of the baselines used in Egypt and an advanced estimated accuracy before starting the project. The experimental test studies the performance of the position accuracy related to the relation between three factors: observation session, final, rabid, and ultrarabid products, and the baseline lengths. Ground control point mediates Egypt was selected as a test point. Nine surrounding IGS stations were selected as reference stations, and the coordinates of the tested point were calculated based on them. Baselines between the tested point and the IGS stations were classified regarding proposal criteria. The coordinates of the tested point were obtained in different observation sessions (0.5, 1, 2, 4, 5, 6, 7, 7.5 h). The results indicated that the lengths of the baseline in Egypt were classified short (less than 600 km), medium (600-1,200 km), and long (greater than 1,200 km) and required a minimum observation time of 4, 5, and 7 h to obtain accuracy 10, 19, 48 mm sequentially. The position accuracy was superior for the rapid and the final than the ultra-rapid products by 16%. A short baseline was at the best case; there was a performance in position accuracy with a 57% deduction in observation time compared with the long baseline.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2382-2386
• /
• 2003

The Global Positioning System(GPS) is a satellite based precise positioning system avaliable worldwide. The GPS have many error sources. The earth's ionosphere and atmosphere cause delays in the GPS signal that translate into position errors. Some errors can be factored out using mathematics and modeling. The configuration of the satellites in the sky can magnify other errors. The problem of accuracy on GPS measurement data can be meaningful. In this study, we propose the method for GPS positioning accuracy improvement. The FUZZY set theory on PDOP(Position Dilution of Precision) and SNR(Signal to Noise Ratio) provide improved for measured positioning data. The accuracy of positioning has been improved by selecting data from original using the FUZZY set theory on PDOP and SNR.

• Journal of Korean Port Research
• /
• v.15 no.1
• /
• pp.75-85
• /
• 2001

Accuracy of dredging processes depends on the types of equipment used, the sediments encountered, whether the work to be performed is new or maintenance dredging, pre- and post-hydrographic surveying and so forth. Among those, position surveying accuracy which is directly determined by the control of the dredge's position and depth surveying accuracy being surveyed at the dredging point during dredging work are important factors. The purpose of this study is to develop 'Dredge Management System'for Grab dredge which is composed of 4 sub-system using LADGPS for dredge position determining system and dredging point determining system, tide gauge system and optical sensor for depth determining system and GIS and ENC for total management system. This system is installed on the grab dredge 'EUNJIN G-18'and applied to anchorage dredging work. at Pohang Harbor. The results revealed that this system is easy to operate, achieves good accuracy with only 45cm unevenness, reduces working period by 22 percent and saves cost 16.6 percent.