• 대한전기학회논문지
• /
• 제36권10호
• /
• pp.703-712
• /
• 1987

A position detection method for 2 phase bifilar permanent magnet step motors is proposed. The back emfgenerated on 2 phase windings by rotor permanent magnet is calculated using motor terminal voltage and current by analog circuit, and the rotor position output is obtained from tese back emf signals through some logical manipulation circuit. This position detector functionally acts like a 2 channel optical incremental encoder, and it is also shown by experimental results that it works well over wide range of speed or under resonant condition where the rotor rings around the detent position. Its resolution is twice of the number of steps per revolution. Bu software implemented on micro-processor, the reliability of position output is enhanced, detecting and correcting error dut to external and/ or internal noise.

• 조명전기설비학회논문지
• /
• 제26권5호
• /
• pp.40-47
• /
• 2012

The PMSM position sensor using two rectangular hall sensors can restrictively acquire the 90[$^{\circ}$] position information of rotor according to electrical angle. Thus, the control method using this position sensor cannot react properly to a rapid load torque change. On the other hand, even though a sensorless method has the advantage of acquiring instantaneous rotor position information, the accuracy of position sensor can be determined by the gain value of estimator. This paper suggests a robust speed control method on torque fluctuation condition, which combines low cost two rectangular hall sensors and sensorless control method.

• 한국측량학회지
• /
• 제29권5호
• /
• pp.519-525
• /
• 2011

High-resolution earth-observing satellites acquire substantial amount of geospatial images. In addition to high image quality, high-resolution satellite images (HRSI) provide unprecedented direct georegistration accuracy, which have been enabled by accurate orbit determination technology. Direct georegistration is carried out by relating the determined position and attitude of camera to the ground target, i.e., projecting an image point to the earth ellipsoid using the collinearity equation. However, the apparent position of ground target is displaced due to the atmosphere and satellite velocity causing significant georegistration bias. In other words, optic ray from the earth surface to satellite cameras at 400~900km altitude refracts due to the thick atmosphere which is called atmospheric refraction. Velocity aberration is caused by high traveling speed of earth-observing satellites, approximately 7.7 km/s, relative to the earth surface. These effects should be compensated for accurate direct georegistration of HRSI. Therefore, this study presents the equation and the compensation procedure of atmospheric refraction and velocity aberration. Then, the effects are simulated at different image acquisition geometry to present how much bias is introduced. Finally, these effects are evaluated for Quickbird and WorldView-1 based on the physical sensor model.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2011년도 춘계학술대회
• /
• pp.307-309
• /
• 2011

최근 출시되는 고사양의 Hand-phone 적용되어진 Camera Module은 대부분 Auto Focusing기능이 탑재되어 있으며 Camera Module의 화소수가 높아지면서 좀 더 정밀하고 안정적인 AF구동제품이 소비자에 의해 요구되고 있다. 본 논문은 현재 출시되고 있는 Camera Module적용 VCM(Actuator)의 문제점인 Auto Focusing시 Lens 초점위치 및 Module 자세에 따른 해상도편차 발생으로 해상도 보증 및 안정된 Actuator 구동을 위해 개선된 구조의 Hybrid VCM을 제안한다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.402.1-402.1
• /
• 2014

Photonic force microscopy (PFM) is an optical tweezers-based scanning probe microscopy, which measures the forces in the range of fN to pN. The low stiffness leads proper to measure single molecular interaction. We introduce a novel photonic force microscopy to stably map various chemical properties as well as topographic information, utilizing weak molecular bond between probe and object's surface. First, we installed stable optical tweezers instrument, where an IR laser with 1064 nm wavelength was used as trapping source to reduce damage to biological sample. To manipulate trapped material, electric driven two-axis mirrors were used for x, y directional probe scanning and a piezo stage for z directional probe scanning. For resolution test, probe scans with vertical direction repeatedly at the same lateral position, where the vertical resolution is ~25 nm. To obtain the topography of surface which is etched glass, trapped bead scans 3-dimensionally and measures the contact position in each cycle. To acquire the chemical mapping, we design the DNA oligonucleotide pairs combining as a zipping structure, where one is attached at the surface of bead and other is arranged on surface. We measured the rupture force of molecular bonding to investigate chemical properties on the surface with various loading rate. We expect this system can realize a high-resolution multi-functional imaging technique able to acquire topographic map of objects and to distinguish difference of chemical properties between these objects simultaneously.

• 소성∙가공
• /
• 제13권3호
• /
• pp.273-278
• /
• 2004

This paper subscribes the measurement system that can position the target to measure by moving 2-axis stage, which is controlled by the data from image processing technique. The high resolution camera and lens are used in measurement of micro mechanical part, but the region of measurement is very small. It is necessary the re-positioning to measure several regions in one part. The system described in this paper has the accuracy with about $0.9\mu\textrm{m}$ resolution per one pixel and can be applied to measure micro mechanical part.

• 생명과학회지
• /
• 제8권4호
• /
• pp.373-380
• /
• 1998

A considerable change observed in X-ray diffraction during the muscle contraction was that the movement of myosin head and conformational change of contractile monecules were occurred in the muscle contraction. Time slice requires tension peak after the onset of stimulation and the height of tension peak depends on the number of twitch cycle. The intensity of I$_{11}$, I$_{10}$, 143${\AA}$ reflection is measured with 5ms time resolution and is recorded in isometric tension. The peak height of I$_{11}$ and 143${\AA}$ intensity is changed after the onset of a stimulation I$_{i}$, and the length of twitch is shortened by successive twitches in the case of stimulation TI$_{i}$. On the other hand, the peak height of I$_{11}$ and 215${\AA}$ intensity starts to decrease at the 1st twitch and remains constant at low peak hight without appreciable recovery during the contraction term. In the case of uccessive twitch stimulation, the myosin heads of muscle are once moved from their resting position and never returned to their initial position.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2011년도 춘계학술대회
• /
• pp.320-323
• /
• 2011

Smart phone에 실장되는 소형 카메라 모듈의 경우, 기존 Handset과 대비하여 Non AF 상태에서의 해상도 수준의 향상에 대한 소비자의 요구가 커지고 있으며, 높은 정밀도와 동일한 반복성 및 빠른 Auto focusing speed를 요구 받고 있다. 이에 따라 기존의 Actuator mechanical position에 기반한 algorithm에서 문제가 되었던 preview(non-AF)의 안정적 해상도 보증 문제 및 속도 개선 한계 문제를 본 논문에서 개선된 algorithm으로 제안하게 되었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.411-414
• /
• 2000

Optical Triangulation Probes (OTPs) are widely used for their simple structure. high resolution, and long operating range. However, errors originating from speckle, inclination of the object, source power fluctuation, ambient light, and noise of the detector limit their usability. In this paper, we propose new design criteria for an error-reduced OTP. The light source module for the system consists of an incoherent light source and a multimode optical fiber for eliminating speckle and shaping a Gaussian beam Intensity profile. A diffuse-reflective white copy paper, which is attached to the object, makes the light intensity distribution on the change-coupled device(CCD). Since the peak positions of the intensity distribution are not related to the various error sources, a sub-pixel resolution signal processing algorithm that can detect the peak position makes it possible to construct an error-reduced OTP system

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1995년도 춘계학술대회 논문집
• /
• pp.40-62
• /
• 1995

A micro positioning system using piezoelectric actuators have very wide application region such as ultra-precision machine tool optical device measurement system. In order to keep a high precision displacement resolution it to useful to take a position sensor and feedback of the error. From the practical point of view high-resolution displacement sensor systems are very expensive and it is difficult to make such a sensitive sensor work properly in a poor operational environment of industry. In this study a piezo-electric micro-depth control system which does not require position sensor but piezoelectric voltage feedback has been developed. It is driven by hysteresis-considering reference input voltage calculated in advance and actuator/sensor characteristics of piezoelectric materials. From the result of experiments a fast and stable response of micro-depth control system has been achieved and an efficient technique to control the piezoelectric actuator suggested.