• 대한기계학회논문집B
• /
• 제35권8호
• /
• pp.815-823
• /
• 2011

다공성 물질 내부의 연소 현상은 저발열량 연료의 연소 및 연소열의 재생을 위한 수단으로 다양한 형태로 산업현장에 응용되고 있다. 하지만 다공성 물질 내부에서의 연소 현상은 직접적인 관찰이 힘들다는 점과 다공성 물질의 복잡한 내부 구조로 인해 매우 제한적인 연구가 진행되어 왔다. 본 연구에서는 복잡한 다공성 물질의 구조 내부에서의 화염의 안정화 특성에 관한 이해를 위해 내부 관찰이 가능하도록 다수의 석영판으로 구성된 다중채널 형태의 모형 연소기를 제안하고 이를 이용한 간단한 실험 결과를 제시한다. 그리고 이러한 다중채널내부 화염의 안정화에 관한 간단한 기초해석 모델을 제안한다. 다수의 채널 내부에 형성된 화염은 채널간의 열전달에 의해 화염의 공간 분포가 변화하고 그 결과로 연소기 내부의 가연한계에 변화가 발생한다. 채널의 재료 특성 및 당량비에 따른 가연한계의 변화를 제시하였으며, 이 결과는 다공성 연소기 내부화염의 이해에 도움될 것이다.

• 대한기계학회논문집B
• /
• 제20권1호
• /
• pp.321-327
• /
• 1996

Experiments were performed on the laminar premixed flame stabilized in a porous medium to know whether the flame downstream of the combustor exists or not. In previous theoretical studies, a stable flame has been predicted in the downstream region of the combustor, but it has never been observed in experiments. In this study, a stable downstream flame could be obtained for the lower burning velocity through circumferential heating by a blue flame positioned outside the periphery of the specially devised combustor. The existence of the stable downstream flame was confirmed by a direct photography of soot line, and temperature measurements. The effect of combustor diameter to flame stability was also considered. As the diameter of the combustor increases, the lean flammability limit was extended.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2014년도 제49회 KOSCO SYMPOSIUM 초록집
• /
• pp.249-251
• /
• 2014

Synthesis gas such as hydrogen and carbon monoxide was produced from $CH_4//oxygen$ mixture using two-section porous media combustor. Heat recirculation through the inner foam structure could extend the flow velocity of stable region over the laminar burning velocity. $H_2/CO$ ratio and module M from concentration of flue gas measured by Gas Chromatography was similar to those calculated by equilibrium. But it was made sure that the heat loss effect becomes more influential than heat recirculation effect as the mixture gets richer. To generate synthesis gas appropriate for methanol production, insulated pressurized porous media combustor will be designed and built in the future.

• 설비공학논문집
• /
• 제6권4호
• /
• pp.399-405
• /
• 1994

Beacuse of the energy resources exhaustion, the aggravating environmental air pollution and the smoke phenomena etc., the importance of clean gas fuel compared with liquid fuel is highly considered in recent years. The combustion system which consists of porous media is actively studied as a new method for solving above problems. Therefore, excess enthalpy combustion using porous media was interested by many researchers and investigated through numerical and experimental analysis. In this study, the simplified combustor has the unique combustion characteristics of mixture gas preheated effect using radiative and convective heat energy by changing the flow passage of unburned gas with solenoid valves and has the intensive excess enthalpy phenomena As the result of according to reduce equivalence ratio, flame temperature was remarkably higher than adiabatic flame temperature. This show the ability of super-lean combustion.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.168-174
• /
• 2000

This paper illustrates the validity of reciprocating type superadiabatic combustor as a industrial applicable dryer. After the investigations of inner and surface temperature distributions of combustor various with air-fuel(methane) ratio, mixture flow rate and reciprocating time, this combustor can be applied in industrial dryer at certain operating conditions. The results are as follows. 1) Higher equilivalence ratio emits more radiation heat flux at the censer chamber 2) Higher mixture flow rate makes more uniform temperature distribution. however, due to the heat transfer from censer chamber to porous media, the radiation beat flux is worse. 3) Longer reciprocating time emit more radiation heat flux. however, this case also makes temperature distribution wide

• 한국연소학회지
• /
• 제18권2호
• /
• pp.1-7
• /
• 2013

Flame stabilization characteristics of premixed flames in narrow annular coaxial tubes (NACT) were investigated experimentally. The NACT burner was proposed as a model of a cylindrical refractory burner, and it was made of quartz tubes. Flame stabilization conditions affected by the characteristic length of the burner was investigated with the variation of the equivalence ratio and the flow rates. Flame behaviors in narrow spaces could be directly observed. Conclusively, more wide flame stabilization conditions could be obtained at the case of the decreased channel scale. A flame instability, such as combustion noise was detected concerned with the flame oscillation observed at the surface of multi channel stage. Some flame propagation characteristics had complicated tendencies that may exist in practical porous-media combustors. Therefore, this NACT burner can be a basic configuration for the development of flame stabilization model in porous media combustor, and it will enhance our understanding about the behavior of flames in meso-scale combustion spaces.

• 대한기계학회논문집B
• /
• 제20권1호
• /
• pp.328-335
• /
• 1996

The one-dimensional flame analysis was carried out to understand the combustion phenomena in porous media. The downstream as well as upstream solution corresponding to upper and lower solutions could be obtained. While upper flame temperature gets higher, lower flame temperature gets lower, as the flame approaches the central part of the combustor. The reason why upstream flame and downstream flame exist at the same flow condition is that the regions where net heat recirculation is identical exist in upstream and downstream of the combustor. In order for the downstream flame to be stabilized, more heats needed to be recirculated towards upstream because of larger radiation loss of downstream flame.

• 한국항공우주학회지
• /
• 제40권9호
• /
• pp.781-788
• /
• 2012

공개소스 전산유체 해석 라이브러리인 OpenFOAM을 이용하여 액체 로켓 연소기의 산화제 매니폴드 내 유동 해석을 수행하였다. 정상 상태의 비압축성 난류 유동 해석을 통하여 분사기 차압 모사를 위한 다공성 매질 영역이 포함된 복잡한 3차원 형상에 대한 유동해석에 있어서의 OpenFOAM 적용 가능성을 평가하였다. 향후 로켓 연소장치 내의 주요 물리적 현상을 포함한 보다 다양한 해석 사례에 대한 평가를 수행함으로써 설계 평가 및 해석 도구로서의 OpenFOAM의 유용성 및 적용 범위를 확인/확대해나갈 계획이다.

• 대한기계학회논문집B
• /
• 제20권10호
• /
• pp.3243-3250
• /
• 1996

Emission characteristics of nitric oxides and carbon monoxide from a porous media combustor has been experiment studied. The relationship between the change of flame shape and emission has also been examined. As the equivalence ratio decreases, the flame shape on the ceramic matrix plate changes from a diffusion flame, R(radiant)-type flame, to B(Blue)-type flame. With large fuel flow rate, R-type flame turns to be two dimensional R-II type flame around the equivalence of 0.7. Carbon monoxide emission increases very rapid with decreasing equivalence ratio. It changes a lot from some 10 ppm to 100-10,000 ppm with the change of flame type from R-I to R-II type. Nitric oxide emission from the premixed burner is less than 25 ppm over all range of fuel flow rate, which is less than 20% of NOx emission from conventional gas burners.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2015년도 제51회 KOSCO SYMPOSIUM 초록집
• /
• pp.73-74
• /
• 2015

Synthesis gas such as hydrogen and carbon monoxide was produced from $CH_4/oxygen$ mixture using insulated pressurized porous media combustor. Experimentally, two cylindrical SiC foams with the different pore density were piled up in a quartz tube and fully premixed mixture was supplied in the axial direction. After stabilizing fuel-rich flame at the interface of the two foams at several pressure conditions, mole fractions of synthesis gases were measured by gas chromatography. Heat recirculation through the inner foam structure could extend the flow velocity of stable region over the laminar burning velocity. As the pressure increased, the rich flammability limit, $H_2/CO$ ratio, and module M increased.