• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.05a
• /
• pp.84-89
• /
• 1996

The nucleation and growth of microporosities was observed during the course of annealing treatment of sputter-deposited AgInSbTe thin films. There was a close correlation between the density of microporosity and the sputtering gas pressure in annealed thin films. The void density for a given composition decreased with sputtering gas pressure. It was shown from the present study that the number of porosities decreased while the average porosity size increased as the annealing temperature and holding time increased. The mechanism of porosity formation in the sputter-deposited AgInSbTe thin flus containing Ar-impurity trapped from the Ar-plasma is discussed in the present article.

• Korea-Australia Rheology Journal
• /
• v.20 no.1
• /
• pp.7-14
• /
• 2008

The objective of this work is to propose a procedure to simulate the flow in the LCM (Liquid Composites Molding) processes by finite difference discretization in a curvilinear coordinate system adapted to the shape of the saturated zone. The numerical results obtained are compared with experimental results obtained by an experimental device elaborated at our laboratory. It allows to realize linear and radial injections for different porosities and to observe the flow front kinetics. Numerical and experimental results are then compared with those of the literatures and excellent agreements are noticed. Finally, we suggest a concept of the capillary number to explain the variations of the permeability obtained for pressure values lower than 0.25 Bar.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.6
• /
• pp.855-859
• /
• 2012

Silicon nanowires (SiNWs) were fabricated by a metal-assisted chemical etching of Si and the porous structure on their surfaces was controlled by changing the volume ratio of the etching solution composed of hydrofluoric acid, hydrogen peroxide, and deionized water. The concentration of hydrogen peroxide as the oxidant was varied for controlling the porosity of SiNWs. The optical properties of porous SiNWs were unique and very different from those of single-crystalline Si, as characterized by measuring their photoluminescence and Raman spectra for different porosities.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.1244-1249
• /
• 2002

In this study, the physical characteristics of steel-wire sound absorbing materials with different thickness and bulk density is experimentally obtained in terms of the porosity and specific flow resistivity. Based on the experimental results, the following conclusions can be made. The porosities of steel-wire sound absorbing materials are smaller than those of general absorbing materials, which are inversely proportional to the volume densities. For the porosity measurement with a good accuracy, the dynamic correction based on the system compliance should be involved in porosity measurement. In addition, the flow condition for the precise measurement of the specific flow resistivity of steel-wire sound absorbing materials should be limited in the laminar flow region.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.896-905
• /
• 1996

Pressure drop, as a function of air flow, was measured for tomatoes and mandarins in bulk with different sizes, stacking arrangements and bed porosities. Pressure drop was also measured on carton vent holes and on a carton of packed fruits . and the cumulative effects of air flow resistance of vent holes and packed fruits in bulk on the air flow resistance of a carton of fruits were evaluated . Equation were presented to describe pressure drop bulk fruits, of an empty carton and of a carton of packed fruits as related to the air velocity , the bed porosity, the fruit diameter and the opening ratio of the vent hole.

• Transactions of Materials Processing
• /
• v.16 no.3 s.93
• /
• pp.210-214
• /
• 2007

Manufacturing bulk nanostructured materials with least grain growth from initial powders is challenging because of the bottle neck of bottom-up methods using the conventional powder metallurgy via compaction and sintering. In the study, densification behavior of nano Cu powders during pressureless sintering was investigated using an in-situ optical dilatometer technique. The initial heating and steady temperature stages during the sintering of nano Cu powder compacts were observed. At the initial heating stage, the powder compact has many porosities and full densification needs high temperature and/or high pressure sintering. In the experimental analysis, changes in geometry and density were measured and discussed for optimal consolidation and densification by the in-situ optical dilatometer.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.9 s.102
• /
• pp.1003-1008
• /
• 2005

The acoustic absorption of a multiple layer perforated plate system is very good near the resonance frequency region, while it has been regarded as a demerit that its frequency bandwidth is considerably narrow. In order to overcome such a demerit, the parallel perforated plates with different porosities are proposed. The sound absorption of such system composed of a parallel perforated plate is calculated by an equivalent electroatoustic circuit approach and validated by comparing the calculated absorption coefficients with those measured by the two-microphone impedance tube method. The sound absorptive characteristics and performance of parallel perforated plate systems are discussed from a standpoint of frequency bandwidth related with sound absorption.

• Advances in nano research
• /
• v.8 no.4
• /
• pp.283-292
• /
• 2020

In the present research, differential quadrature (DQ) method has been utilized for investigating free vibrations of porous functionally graded (FG) micro/nano beams in thermal environments. The exact location of neutral axis in FG material has been assumed where the material properties are described via porosity-dependent power-law functions. A scale factor related to couple stresses has been employed for describing size effect. The formulation of scale-dependent beam has been presented based upon a refined beam theory needless of shear correction factors. The governing equations and the associated boundary conditions have been established via Hamilton's rule and then they are solved implementing DQ method. Several graphs are provided which emphasis on the role of porosity dispersion type, porosity volume, temperature variation, scale factor and FG material index on free vibrational behavior of small scale beams.

• Carbon letters
• /
• v.4 no.4
• /
• pp.180-184
• /
• 2003

The role of KOH in the one-stage KOH-activation of rice straws was studied using FTIR, XPS, TGA, and DTG techniques. It was found that at the impregnation, KOH extracts to some extent the lignin component from rice straw and reacts with hydroxyl groups. On heat-treatment, the impregnated KOH facilitates intermolecular condensation reaction on one hand but retards the thermal degradation of cellulose molecules on the other hand. The oxygen-containing surface functional groups newly created by oxidation of KOH may facilitate the bulk, not controlled, consumption of carbon atoms so that the effective porosities may not be able to be developed by the one-stage activation process.

• Transactions of Materials Processing
• /
• v.9 no.1
• /
• pp.10-16
• /
• 2000

This research investigates microstructures and fatigue properties of the weldments of 6005A aluminum alloy developed for railroad vehicles. The samples were extruded into a truss structure and welded together using the gas metal arc welding process. The extruded sample showed a wide variation in grain size, possibly due to the frictional heating as well as the inghomogeneous metal flow in the extrusion die. The mechanical properties of the samples were affected by the mirocstructures. The fatigue strength of the welded structure was found to decrease significantly from that of the base metal. It was found that the fatigue characteristics of the welded structure were determined by the microstructure of the parent metal as well as weld defects such as porosities and the liquation cracks.