• 한국화재소방학회논문지
• /
• 제26권6호
• /
• pp.24-30
• /
• 2012

본 연구는 저압 선로의 접촉 부분에서 발생할 수 있는 접촉 불량과 그 부분의 진동이 결합될 경우 발생될 수 있는 불꽃 및 직렬 아크를 검출할 수 있는 방법에 대한 것이다. 일반적으로 전기화재의 원인은 과전류, 단락, 접촉불량 등 여러 가지가 있을 수 있다. 이 중 과전류 및 단락 등은 선로에 흐르는 순간 전류량을 검출하여 감지할 수 있으나, 접촉불량은 전압, 전류값의 초과분 및 파형의 왜곡으로는 검출하기가 어려운 점이 있다. 따라서 본 논문에서는 퍼지논리 및 다차원 기법을 이용하여 최적의 아크 판단 기법을 연구하고, 아크 검출 및 검증을 위한 모의실험과 제어기 실험 및 부하실험을 실시하였다. 그 결과 제어기 및 검출 알고리즘이 여러 가지 부하와 상관없이 정상적인 부하의 파형과 아크 발생시의 파형을 구분하여 성공적으로 직렬아크를 검출하였다.

• 한국화재소방학회논문지
• /
• 제18권4호
• /
• pp.57-63
• /
• 2004

본 연구에서는 저압용 누전차단기 접속단자에서의 접촉압력에 따른 발열특성을 조사하고 차단기 단자와 전선에 접촉 불량이 발생했을 때의 전압, 전류파형과 산화물 증식 등을 분석하였다. 차단기 단자와 전선에 접촉압력이 가해지지 않았을 때는 접촉저항증가로 열이 발생하고 금속표면에 산화 막이 형성되었다. 이때 단자 외부 절연물의 온도는 접촉 불량에 의해 급격하게 상승하며 단자내부에서 미세한 불꽃과 연속적인 방전음이 발생하였다. 단자내부도체와 접속전선 접촉면에서 기계적 진동에 의한 접촉 불량이 발생했을 때, 접촉면에서 산화물이 증식되고 발열온도는 869℃이상으로 상승하여 전기재해의 위험이 높음을 알 수 있었다.

• 한국안전학회지
• /
• 제32권2호
• /
• pp.27-33
• /
• 2017

This study is intended to identify issues on the basis of investigating the actual state of laboratory environment and outlet circuit, and derive end states by expressing sequences from the initiating event of disaster to accident in leakage current, poor contact and overload through ETA(event tree analysis). To this end, this study investigated the actual state of electric equipment of laboratory at universities in all parts of country. And it is shown that most of them are failure in electric work and user negligence in the investigation of actual state. It is found that there is earth fault and defect in wire diameter in the failure of electric work and the problem of partial disconnection due to wire bundling and poor contact in user negligence. Outlet-related component, failure rate and initiating events are composed of a total of 41 initiating events, i.e., 30 internal initiating events and 11 external initiating events. And end states are composed of a total of 15 parts, i.e., 3 electric power parts and 12 safety parts. Earthing class 3 is the most important safety device against leakage current (initiating event). And in case of poor contact, it is necessary for manager to check thoroughly because there is no safety device. In case of overload/overcurrent, when high-capacity equipment is connected, a molded case circuit breaker, safety device, worked. However, in most cases, it is verified that this doesn't work. This study can be utilized as electric equipment safety guide for laboratory safety manager and managers.

• 한국안전학회지
• /
• 제34권3호
• /
• pp.15-20
• /
• 2019

As industry is progressing and standards of living are improved, the demand of electrical energy is expected to grow 8-9% annually. Therefore, the importance of electrical fire prevention technology with the ability of the power supply is being emphasized. According to the statistics of fire in Korea, fire occurred about 45,000 cases annually, and electrical fire possessed about 20%. The electrical fire by poor contact has increased gradually, can be connected as great fire to secondarily induce short circuit and earth fault. Then analysis of heating causes of electrical connections between copper and copper alloy is needed. Also, detection and analysis algorithm of oxide at copper alloy are necessary. In this research, in order to understand the characteristics of oxide growth with rising resistance and heating, it is demonstrated that the oxide at electrical connections can cause fire due to arcing.

• 대한금속재료학회지
• /
• 제47권7호
• /
• pp.423-432
• /
• 2009

In the galvanizing coating process, the effects of the silicon content on the coatability and wettability of molten zinc were investigated on Dual-Phase High Strength Steels (DP-HSS) with various Si contents using the galvanizing simulator and dynamic reactive wetting systems. DP-HSS showed good coatability and a well-developed inhibition layer in the range of Si content below 0.5 wt%. Good coatability was the results of the mixed oxide $Mn_{2}SiO_{4}$, being formed by the selective oxidation on the surface, with a low contact angle in molten zinc and a large fraction of oxide free surface that provided a sufficient site for the molten zinc to wet and react with the substrate. On the other hand, with more than 0.5 wt%, DP-HSS exhibited poor coatability and an irregularly developed inhibition layer. The poor coatability was due to the poor wettability that resulted from the development of network-type layers of amorphous ${SiO}_{2}$, leading to a high contact angle in molten zinc, on the surface.

• 한국화재조사학회학술대회
• /
• 한국화재조사학회 2010년도 제 19회 춘계학술대회
• /
• pp.66-81
• /
• 2010

본 논문에서는 콘센트와 플러그 접속부에서의 접촉불량에 의한 열화특성에 대하여 실험, 분석하였다. 부하의 크기와 시간 경과에 따른 전기적 특성을 분석하였으며 도전 재료와 절연재료의 외형, 표면구조, 열화특성을 분석하였다. 실험결과는 접촉불량에 의한 전기화재 예방과 화재원인 분석에 활용 가능할 것으로 기대된다.

• 한국안광학회지
• /
• 제10권3호
• /
• pp.237-240
• /
• 2005

The cause of poor visual acuity was connected to the damage by the ocular trauma related. Especially the most cause of visual disorder was identified as irregular pupil by ocular damage. Therefore most patients stopped the wearing of the contact lens immediately by the visual decrease effects from irregular pupil disorder. But we had suggested that the contact lens wear was a very intensive visual therapy. We had identified the visual recover from several tests using the contact lens treatment.

• Journal of Electrochemical Science and Technology
• /
• 제7권3호
• /
• pp.228-233
• /
• 2016

It is hard to employ the carbon materials or the lithium metal foil for the anode of lithium sulfur batteries because of the poor passivation in ether-based electrolytes and the formation of lithium dendrites, respectively. Herein, we investigated the electrochemical characteristics of lithium sulfur batteries with lithiated silicon anode in the liquid electrolytes based on ether solvents. The silicon anodes were lithiated by direct contact with lithium foil in a 1M lithium bis(trifluoromethane sulfonyl) imide (LiTFSI) solution in 1,2-dimethoxyethane (DME) and 1,3-dioxolane (DOL) at a volume ratio of 1:1. They were readily lithiated up to ~40% of their theoretical capacity with a 30 min contact time. In particular, the carbon mesh reported in our previous work was employed in order to maximize the performance by capturing the dissolved polysulfide in sulfur cathode. The reversible specific capacity of the lithiated silicon-sulfur batteries with carbon mesh was 1,129 mAh/g during the first cycle, and was maintained at 297 mAh/g even after 50 cycles at 0.2 C, without any problems of poor passivation or lithium dendrite formation.

• 보건교육건강증진학회지
• /
• 제4권1호
• /
• pp.65-75
• /
• 1987

This study was conducted (i) to recommend the high-scored education method as a adaptable method, and (ii) to find the most influential factor among the three acceptability components (feasibility factor, stimulation factor and reliability factor) to urban or rural residents. The accept-ability score of each health education method currently existing in urban and rural area was estimated. A total of 257 households in Guro 6-dong, Seoul, and 233 households in Jeomdong-myeon, Yeoju-gun, were sampled by interview survey using questionnaire. The four types of health education methods used in this study are; printed matter method, mailing service method. personal contact method, and group contact method. The major findings obtained from this research are as follows; 1) In urban area, the highest-scored in terms of acceptability is the personal contact method, followed by the mailing service, the printed matter, and the group contact. The mailing service method is found to be effective especially for the intelligent group people. 2) In rural area, the highest-scored in terms of acceptability is also the personal contact method, followed by the group contact, and printed matter method. In general, the group contact method is effective toward both urban-poor and rural housewives (especially in stimulation factor). To improve the health consciousness of the residents, there arises the need for the existing education program into better organized and diversified one and for educating health-educators by providing in-depth health knowledge.

• 한국표면공학회지
• /
• 제35권2호
• /
• pp.129-137
• /
• 2002

The purpose of solderability assessment is to predict the effectiveness of soldering process. It is important for companies pursuing zero defects manufacturing because poor solderability is the major cause of two third of soldering failures. The most versatile solderability method is wetting balance method. However, there exist so many indices for wettability in the wetting balance test e.g. time to reach 2/3 values of maximum wetting force, tine to reach zero wetting force, maximum withdrawal force. In this study, three solderability assessment methods, which were the maximum withdrawal force, the wetting balance and the dynamic contact angle (DCA), were evaluated by comparing each other. The wetting balance technique measures the solderability by recording the forces exerted from the specimen after being dipped into the molten solder. Then the force at equilibrium state can be used to calculate a contact angle, which is known as static contact angles. The DCA measures contact angles occurred during advancing and withdrawing of the specimen and the contact angles are known as dynamic contact angles. The maximum withdrawal force uses the maximum force during withdrawal movement and then a contact angle can be calculated. In this study, the maximum withdrawal force method was found to be an objective index for measuring the solderability and the experiment results indicated good agreement between the maximum withdrawal force and the wetting balance method.