• 한국화재소방학회논문지
• /
• 제32권5호
• /
• pp.34-39
• /
• 2018

본 연구에서는 구획 공간 화재 시 발열량이 급격히 변하는 조건에서 스프링클러헤드의 손실인자 변화에 따른 작동시간을 분석하였다. 이를 위해서 내화보드로 구성된 구획 공간의 크기가 폭 0.3 m, 세로 0.5 m, 길이 3.0 m인 구조물을 제작하고 헵탄(n-Heptane) 풀 화재 실험을 수행하여 구획 공간 내부의 온도 분포, 헵탄의 질량감소율 그리고 발열량을 산출하였다. 또한, Fire Dynamics Simulator (FDS) Version 6.5를 사용하여 실험 조건과 동일한 발열량을 가정하고 스프링클러헤드의 설치위치 및 손실인자(C-factor) 변화에 따른 작동 시간을 분석하였다. 그 결과 반응시간지수(Response Time Index, RTI)가 $100(m{\cdot}s)^{0.5}$이고 작동온도가 $72^{\circ}C$인 스프링클러는 화원 상층부의 기류 온도가 $100^{\circ}C$에서 $300^{\circ}C$로 상승하고, 기류의 속도가 약 0.7 m/s인 경우 C-factor = 0과 1일 때 스프링클러의 작동시간은 최소 30 s~60 s, C-factor = 3일 때 62 s에서 최대 92 s, C-factor = 5일 때 120 s 이상으로 나타났다.

• 대한기계학회논문집
• /
• 제18권5호
• /
• pp.1235-1244
• /
• 1994

In this study, experimental results of the nucleate boling of wire-wrapped tubes are provided. Both water and R-113 were boiled. Solid stainless steel wires, stranded copper wires and stranded nylon wires were tested. Solid stainless wire is effective to enhance the boiling of water. The performance is approximately the same(or slightly better at certain conditions) as that of GEWA-T tubes. For the test range of wire diameter 0.6 $mm{\le}d{\le}2.6 mm$, the optimum gap width increases as the wire diameter increases. The maximum heat transfer coefficient was obtained for the 1.0 mm diameter wire, and it is 1.6 times larger than that of the GEWA-T at the heat flux of 20 $kW/m^{2}.$ Solid stainless wire is also effective to enhance the boling of R-113 at low heat fluxes. The performance of the wire-wrapped tube approaches that of GEWA-T. At high heat fluxes, however, the enhancement decreases. The reason may be attributed to the cavity shape and the high wettability of the refrigerants. Stranded copper or nylon wire is effective to enhance the boiling of R-113. The performance is approximately the same(or slightly better) as that of GEWA-T tubes. Maximum heat transfer was obtained for the stranded nylon wire, and it is approximately 1.4 times larger than that for the GEWA-T at the heat flux of 20 $kW/m^{2}.$ The reason may be atrributed to the favorable thermal environment in the restricted regions formed by twisted wires.

• 한국수자원학회논문집
• /
• 제48권3호
• /
• pp.169-183
• /
• 2015

하천 복원을 위한 기초 작업으로서 자연 상태에 가까운 하천의 지형학적 특성을 파악하기 위해 과거 및 현재 자료를 이용하여 하천지형학적 분석을 실시하였다. 대상 하천은 미호천과 내성천이다. 분석에 포함된 지형학적 변수는 하곡변수인 곡저폭, 하도 형상변수인 사행도, 강턱하폭, 하도경사, 구성재료 변수인 하상재료, 지배 변수인 강턱유량, 비유수력이며, 지배적인 프로세스가 함께 고려되었다. 분석 결과 두 하천은 비슷한 유역면적을 갖는 모래하천이지만, 곡저폭, 하도 형상변수, 종단적 위치에 따른 지배적인 프로세스 등에서 차이가 있는 것으로 나타났다. 또한 지형학적 변수들 사이의 상호 관계를 분석하였다. 그 결과 강턱하폭은 강턱유량에 비례하여 증가하였고, 그 경향성은 기존의 연구 결과와 대체로 일치하고 있다. 강턱유량과 하도경사를 분석한 결과 미호천은 사행하천과 망상하천의 특성을 나타내고 있는 반면, 내성천은 대부분의 구간에서 망상하천에 해당하는 것으로 나타났다. 하도경사와 하폭수심비 관계를 이용하여 지배적인 프로세스를 분석한 결과 미호천은 사구-연흔의 특성을 나타내고 있으나 내성천은 하류에서는 망상하천 특성이 지배적인 반면, 상류에서는 여울-소 내지는 평하상 특성이 지배적인 것으로 나타났다. 과거 자료를 이용한 분석 결과는 정비된 하천의 자료를 이용한 분석 결과에 비해 합리적인 것으로 나타났다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권4호
• /
• pp.464-471
• /
• 2002

Porosity formation in partial penetration welds by high power lasers is a serious problem in industry. There are two main causes that induce porosity formation. One form of porosity is due to gases (e.g. hydrogen, oxygen) dissolving into the weld pool because of the high temperature and then the rapid solidification traps gases as a bubble in the weld metal. The second problem is voids formed by the keyhole collapsing due to unstable keyhole fluid dynamics. The voids that form at the bottom of the keyhole are relatively large and irregular in shape compared to the gas bubbles; this void formation is the primary concern in this paper. The reduction of voids formed by keyhole collapse is achieved by improving the stability of keyhole. Two methods to improve keyhole stability are discussed in this paper: pulse modulation and beam incident angle. Pulse modulation of the laser beam was performed between 100 Hz and 500 Hz to find out the optimum frequency for the keyhole dynamics. The incident beam angle changed the impact angle of the laser beam to the work surface in a range of 0 to 25 degrees. Glycerin in a semi-solidified state is used as a medium for performing the welding because its transparency allows of visualization of the keyhole.

• 한국의류학회지
• /
• 제27권8호
• /
• pp.946-957
• /
• 2003

This study aimed to suggest a simple and well-fitting flat pattern drafting method for a men's jacket. Four jackets in thick muslin were made from four different drafting methods utilizing a few measures as breast girth, center back length, and chest width, which were not much different from the drafting methods of woman's jacket. The appearance of the 4 jackets was evaluated by a pool of evaluators consisted of graduate students who had much clothing construction teaching experiences and their motion adaptability was evaluated by two wearers who belonged within the range of the average measures of the Korean male figure as reported from the 1997's Census for Standard Body Measure. A drafting method evaluated as the most well-fitting and well-functioning in general was chosen and modified to enhance the appearance and was reevaluated to confirm its fit improvement. As a result of this study, a new drafting method, simple and not much different from that of a woman's jacket pattern drafting method is proposed. Since this method is based on the minimal measures and ratios thereof, and is not as complicated as ordinary drafting methods for men's wear, the researcher expects that this drafting method allows more chances for the students to learn and understand men's wear more easily and comfortably.

• 한국환경복원기술학회지
• /
• 제10권3호
• /
• pp.71-87
• /
• 2007

In order to improve and manage rationally for Youngdam creek in Haman-gun, the channel change, water quality and ecological adaptation etc. were evaluated by monitoring during three years. The distinct differences of channel characteristics appeared in the extents of bed excavation and the revetment methods because overall reconstruction was occurred intense disturbance of width expansion and levee construction etc. The scour and deposition were caused according to channel characteristics of ripple and pool, and the adaptation of vegetation was distinguished from each revetment methods clearly. Water quality was maintained first class on the basis of BOD as 0.5~1.5mg/${\ell}$. The vegetation appeared in 380 species close-to-nature river improvement before, but 64 species it after one year, 159 species it after two year and 158 species it after three year. The animal life appeared in 123 species of close-to-nature river improvement before, but 103 species it after one year, 116 species it after two year and 119 species it after three year.

• 터널과지하공간
• /
• 제14권4호
• /
• pp.269-274
• /
• 2004

본 연구에서는 터널에서 화재 발생시 역기류의 위치를 결정하기 위하여 축소실험을 실시하였다. Froude 상사를 사용하여 1/20로 축소된 모형터널에서 실험을 실시하였으며 가연물질로는 에탄올을 사용하였다. 한 변의 길이가 8-16cm의 화원을 사용하였으며 발열량은2.47-12.30㎾이다. 터널 단면의 종횡비(터널높이/터널폭)가 증가할수록 역기류를 제어하기 위해 더 큰 배연 풍속이 요구됨을 확인하였다. L$_{B}$$^{*}$ ＜5일 때 역기류를 막기 위한 배연속도가 0.25승에서부터 발열량에 비례하여 증가한다. L$_{B}$$^{*}$ $\geq$5에서는 발열량의 0.3승에 비례한다.

• 대한기계학회논문집A
• /
• 제27권2호
• /
• pp.310-316
• /
• 2003

One of the significant subject in the automatic arc welding is to establish control system of the welding parameters for controlling bead geometry as a criterion to evaluate the quality of arc welding. This paper proposes an inference algorithm for bead geometry in CMA Welding using Neuro-Fuzzy algorithm. The characteristic welding parameters are measured by the circuit composed of hall sensor, voltage divider tachometer, etc. and then the bead geometry of each weld pool is calculated and detected by an image processing with CCD camera and a measuring with microscope. The relationships between the characteristic welding parameters and the bead geometry have been arranged empirically. From the result of experiments, membership functions and fuzzy rules are tuned and determined by the learning of neural network, and then the relationship between actual bead geometry and inferred bead geometry are concluded by fuzzy logic controller. In the applied inference system of bead geometry using Neuro-Fuzzy algorithm, the inference error percent is within -5%∼+4% in case of bead width, -10%∼+10% in bead height, -5%∼+6% in bead area, -10%∼+10% in penetration. Use of the Neuro-Fuzzy algorithm allows the CMA Welding system to evaluate the quality in bead geometry in real time as the welding parameters change.

• 한국환경복원기술학회지
• /
• 제16권6호
• /
• pp.119-133
• /
• 2013

The purpose of this study is to develop riverbed techniques to activating ecological function of hyporheic zone. Hyporheic zone maybe simply defined as an active eco-tone between surface water and groundwater, which facilitates to exchange water, nutrients and aquatic habitat occur in response to variation in discharge and bed geomorphology. The aim of this study is to evaluate the effectiveness of an applied riverbed technique for two years since its installation in the hyporheic zone. The experimental riverbed technique has been implemented on Anyang stream penetrating Anyang city in Gyunggi province. The dimension of the installed structure is 5.0 m in width, 46 m in length. Bottom layer is filled with rip-rap covered with gabion. After the implementation of the technique, the study conducts follow-up monitoring in two years of between 2011 and 2012. The results of follow-up monitoring for two years are as follows:1) In Hydro geomorphic process, the riverbed technique maintains hydraulic stability despite of several flood events in 2011, 2012. 2) After transformation to form pool-and-riffle habitat, for aquatic community composed of freshwater fish, macro invertebrate, and attached algae, the species diversity and population gradually increased. 3) The riverbed technique achieved desired effect on enhancement of ecological function in hyporheic zone.

• Journal of Welding and Joining
• /
• 제8권3호
• /
• pp.70-78
• /
• 1990

The harsh nature of welding environments makes welding a prime candidate for process automation. Among the variety of welding processes available, gas metal arc welding is one of the most frequently used methods, primarily because it is highly suited to a wide range of applications, and also to automation. Automatic seam tracking method is one of the most demanded techniques for automatic control of arc welding. In this study a seam tracking system has been developed by using the welding arc itself as a sensor. This paper described the principle and experimental result of the arc sensor system, as well as the development and application of the automatic CO_2$ welding for the horizontal fillet welding. A basic problem in horizontal fillet welding is the prevention of hanging bead formation such as undercut at the vertical plate and overlap at the horizontal plate. To produce the symmetric bead shape, the relationship of bead shape to welding parameters(welding velocity, weaving width, weaving speed, tip to workpiece distance) was also investigated.