• 한국화재소방학회논문지
• /
• 제32권3호
• /
• pp.35-41
• /
• 2018

본 연구에서는 2유체노즐을 이용하여 140 ml 헥산 풀화재(Pool fire)에 대한 소화 실험을 수행하였다. 해당 풀화재의 화원(직경 80 mm인 원형) 면적은 $0.005027m^2$이고, 열방출률은 2.81 kW로 측정되었다. 물 공급 유량은 156-483 g/min (~0.156-0.483 l/min), 기체(공기와 질소) 공급 유량은 30-70 l/min이었다. 본 실험조건에서 기체 공급 유량이 많은 경우에 성공적으로 소화가 가능하였다. 소화 가능 영역에서 기체 공급 유량이 적은 경우, 물 공급 유량이 많을 때 화재 소화 소요 시간이 길었고, 물 소모량은 많은 것으로 나타났다. 반면, 기체 공급 유량이 많은 경우, 물 공급유량에 따른 화재 소화 소요 시간 및 물 소모량은 상대적으로 큰 차이가 없는 것으로 나타났다. 한편, 본 실험조건에서 공급 기체의 종류는 소화 가능 여부, 소화 소요 시간, 물 소모량에 큰 영향을 미치지 않는 것으로 측정되었다. 마지막으로 본 실험결과와 단일유체노즐을 이용한 기존 실험결과를 이용하여, 2유체노즐과 단일유체노즐의 140 ml 헥산 풀화재 소화를 위한 물 소모량을 선행적으로 비교 및 검토하였다.

• Nuclear Engineering and Technology
• /
• 제43권3호
• /
• pp.195-204
• /
• 2011

The effects on pool boiling heat transfer of aqueous solutions of boric acid ($H_3BO_3$) and sodium chloride (NaCl) as working fluids have been studied. Borated and NaCl water were prepared by dissolving 0.5~5% volume concentration of boric acid and NaCl in distilled-deionized water. The pool boiling tests were conducted using $1{\times}1\;cm^2$ flat heaters at 1 atm. The critical heat flux (CHF) dramatically increased compared to boiling pure water. At the end of boiling tests it was observed that particles of boric acid and NaCl had deposited and formed a coating on the heater surface. The CHF enhancement and surface modification during boiling tests were very similar to those obtained from boiling with nanofluids. Additional experiments were carried out to investigate the reliability of the additives deposition in pure water. The boric acid and NaCl coatings disappeared after repeated boiling tests on the same surface due to the soluble nature of the coatings, thus CHF enhancement no longer existed. These results demonstrate that not only insoluble nanoparticles but also soluble salts can be deposited during boiling process and the deposited layer is solely responsible for significant CHF enhancement.

• Nuclear Engineering and Technology
• /
• 제53권4호
• /
• pp.1134-1145
• /
• 2021

A design parameter study is presented for the closed-loop type passive containment cooling system (PCCS) which is equipped with two heat exchangers: one installed at the inside of the containment and the other submerged in the water pool at the outside of the containment. A GOTHIC code model for PCCS performance analyses was set up and the design parameters such as the heat exchanger sizes, locations, and water pool tank volumes were analyzed to investigate the feasibility of installing this type of PCCS in PWRs like OPR-1000 being operated in Korea. We identified the size of the circulation loop and heat exchangers as major design parameters affecting the performance of PCCS. The analyses showed that the heat exchangers in the inside of the containment would be more influential on the heat removal capability of PCCS than that installed in the water pool at the outside of the containment. Hence, it was recommended to down-size the heat exchangers in the water pool to optimize PCCS without compromising its performance. Based on the parametric study, it was demonstrated that a closed-loop type PCCS could be designed sufficiently compact for installation in the available space within the containment of PWRs like OPR-1000.

• 연구논문집
• /
• 통권24호
• /
• pp.41-48
• /
• 1994

This experimental study deals with the extinguishiment characteristics of an oil pool flame using the water spray. The water through the six different atomizers is ejected over the freely burning pool flame in the quiescent surrounding air. Injection direction is vertical to the surface of oil in a small tank with a diameter of 100mm and a height of 10mm. In order to estimate quantitatively the extinction, the burning rate as well as the effective water flux are measured. The effective water flux is the amount of the water which reach the pool from the nozzle. The burning rate with the water spray increases until the injection pressure increases to reach some value, which gives the maximum burning rate, while the effective water flux without the flame decreases or does not change according to increasing of the injection pressure. This maximum burning rate is greater than 2.5 times of burning rate of the fire without the water spray. As a matter of the extinguishiment, it is found that the water drops of which size is too small can not extinguish the fire because too small drops does not reach the fuel surface.

• 상하수도학회지
• /
• 제18권3호
• /
• pp.337-342
• /
• 2004

Previous experiment was performed under abiotic condition. Steady-state abiotic experiments in the sand-tank reactor with air flowing through the reactor headspace demonstrated that oxygen supply through the water table interface into the saturated zone was enhanced when an LNAPL (dodecane) pool was present at the water table. Biotic condition was considered in this study. Biotic experiments performed after inoculating the reactor with Pseudomonas putida mt-2, which does not grow on dodecane, indicated that the enhanced oxygen supply in the presence of the LNAPL pool also enhanced biodegradation of a solute (glucose) plume passing beneath the LNAPL pool at steady-state.

• 한국농공학회지
• /
• 제42권1호
• /
• pp.73-82
• /
• 2000

Large quantitive of polllutants are washed into reservoirs during storm events. These polllutants contribute to eutrophication, such as algal blooms and fish kills. This study was conducted for the purpose of assessing the pollutant removal possibilities of sedimentation pool formed by deep dredging of a reservoir inlet. Water quality data were collected in the Masan reservoir, whose inlet has been dredged deep like sedimentation pool. The average concentration of chemical oxygen demand(COD) , toatal nitrogen(T-N) and total phosphrous(T-P) in the deep dredged area were 8.7 ~20.5mg/ι (T-N), 0.17~0.84mg/ι(T-P), which were 4.9%(COD), 29.0%(T-N) and 44.8%(T-P) higher than those of middle part of the reservior. The texture of sediment in the dredged area was silty loam, while that of the middle part was sandy clay loam. Organic matter contents, T-N and T-P of the bottom soil in the dredge area showed higher values than the middle part of the reservoirs. From these results, it was considered thedeep dredged area in the inlet of reservoir might play a key role to settle pollutant particulate. Based on the result of water quality analysis, deep dredging of the reservoir inlet could be assessed to reduce T-N and T-P of the reservoir about 6.5% , 8.3%, respectively. However, the effect of the sedimentation pool would be raised if the settled particles were taken into account in assessing water quality improvement for the reservoir. Accordingly, dredging of a reservoir inlet to make a shape of sedimentation pool is recommended for water quality improvement of reservoir in the stage of dredging plan.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2008년도 학술발표회 논문집
• /
• pp.1675-1678
• /
• 2008

어류는 민감하기 때문에 최적화된 어도를 설계하는 것은 매우 어려운 일이다. 이와 같은 문제를 해결하기 위해서, 관찰, 수리모형시험과 같은 방법을 이용한 연구가 주를 이루어 왔다. 최근 들어 어도에 대한 기본 지식의 축적과 CFD 프로그램이 발전함에 따라 수치모의를 이용해 최적 어도를 설계하고자 하는 노력이 활발해 지고 있다. 본 연구에서는 최적 어도 설계를 도모하기 위해서 어류의 휴식을 위해 설치되는 풀(pool) 내의 흐름해석을 수행하였다. 군남홍수조절지를 대상으로 설계도면을 분석하여 3차원으로 변환하여 구조물형상을 구축하였으며, FLOW-3D 모형을 이용하여 흐름을 해석하였다. 휴식 풀 내의 흐름을 모의한 결과 어도 내 월류 수심이 10cm 일 경우, 휴식 풀 내 유속은 풀 내 유입어도의 노치와 잠공부분에서 최대 유속이 0.4m/s로 나타났고, 국부적으로 집중된 유속에 의해 풀 내 순환류가 발생하나, 유속의 범위가 최대 0.15m/s를 넘지 않는 것으로 모의되었다.

• 대한기계학회논문집B
• /
• 제31권11호
• /
• pp.949-956
• /
• 2007

Pool boiling critical heat flux (CHF) of nanofluids with oxide nanoparticles of $TiO_2$ or $Al_2O_3$ was experimentally investigated under atmospheric pressure. The results showed that a dispersion of oxide nanoparticles significantly enhances the CHF over that of pure water. Moreover it was found that nanoparticles were seriously deposited on the heater surface during pool boiling of nanofluids. CHF of pure water on a nanoparticle-deposited surface, which is produced during the boiling of nanofluids, was not less than that of nanofluids. The result reveals that the CHF enhancement of nanofluids is absolutely attributed to modification of the heater surface by the nanoparticle deposition. Then, the nanoparticle-deposited surface was characterized with parameters closely related to pool boiling CHF, such as surface roughness, contact angle, and capillary wicking. Finally, reason of the CHF enhancement of nanofluids is discussed based on the changes of the parameters.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2001년도 춘계학술발표회요약집
• /
• pp.255-255
• /
• 2001

• 한국화재소방학회:학술대회논문집
• /
• 한국화재소방학회 2002년도 춘계학술대회 논문집
• /
• pp.163-167
• /
• 2002