• Journal of the Korean Vacuum Society
• /
• v.21 no.3
• /
• pp.158-163
• /
• 2012

In this work, we have fabricated the $TiO_2$ thin films on Si and glass, polymer insulator substrates as the self-cleaning coating of polymer insulator. $TiO_2$ films were deposited by RF magnetron sputtering method with $TiO_2$ ceramic target and $TiO_2$ films of 100 nm thickness were fabricated with various RF powers. We have investigated the optical and surface, and structural properties of $TiO_2$ films prepared with various RF powers. As a result, the value of the contact angle of $TiO_2$ thin film is increased with increasing RF power and the value of the rms surface roughness is increased. The transmittance is decreased with increasing RF power. These results indicate that the variation of the surface and optical properties of $TiO_2$ thin films is related to the sputtering effects by increasing RF power.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.293-296
• /
• 2002

Surface relief holograms are fabricated by means of irradiation of laser interference patterns. The diffraction efficiency and the surface relief depth depend on the writing energy and the polarization of the writing laser beam. This structure is very stable at temperatures under glass transition temperature $T_g$ and can be erased by heating above $T_g$. We proposed a new technique to control the surface relief structure. The electric charge was deposited on the surface relief grating in a corona-depositing poling setup in an oven. The first-order diffraction efficiency measured before and after corona discharge increased from about 0.24 % to about 28 %. This diffraction efficiency increase is mainly caused by the increase of the relief depth caused by the electric charge. The relief depth is increased from 20 nm to 350 nm by corona charging. .

• Journal of Sensor Science and Technology
• /
• v.22 no.2
• /
• pp.100-104
• /
• 2013

A superhydrophobic mesh is a unique structure that blocks water, while allowing gases, sound waves, and energy to pass through the holes in the mesh. This mesh is used in various devices, such as gas- and energy-permeable waterproof membranes for underwater sensors and electronic devices. However, it is difficult to fabricate micro- and nano-structures on three-dimensional surfaces, such as the cylindrical surface of a wire mesh. In this research, we successfully produced a superhydrophobic water-repellent mesh with a high contact angle (> $150^{\circ}$) for nanofibrous structures. Conducting polymer (CP) composite nanofibers were evenly coated on a stainless steel mesh surface, to create a superhydrophobic mesh with a pore size of $100{\mu}m$. The nanofiber structure could be controlled by the deposition time. As the deposition time increased, a high-density, hierarchical nanofiber structure was deposited on the mesh. The mesh surface was then coated with Teflon, to reduce the surface energy. The fabricated mesh had a static water contact angle of $163^{\circ}$, and a water-pressure resistance of 1.92 kPa.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.7
• /
• pp.669-673
• /
• 2008

ITO thin film was deposited on PC substrate in Facing Targets Sputtering (FTS) system with various sputtering conditions. After it is applied to external bending force, we investigated how change the surface and electrical property of as-deposited ITO thin film. As the L(face-plate distance) of substrate decreases, it found that the maximum crack density is increasing at the center position and decreasing crack density as goes to the edge. So to apply same curvature (r) and bending force to PC substrate with ITO thin film, we fixed the L that is equal to curvature radius (2r). Before bending test, ITO thin films that deposited in the input current of 0.4 A and thickness of 200 nm already had biaxial tensile failure because of each different CTE (Coefficient of Thermal Expansion) and Others had been shown no bending or crack. After bending test, all samples had been shown cracks at about 200 times and as increasing the crack density, resistivity increased.

• Macromolecular Research
• /
• v.12 no.3
• /
• pp.290-292
• /
• 2004

Multimode channel waveguides were fabricated using a direct UV patterning technology from thick films deposited by the one-step dip-coating of an organic/inorganic hybrid material (ORMOCER(equation omitted). The core size of the covered ridge waveguide was 43${\times}$51 $\mu\textrm{m}$$^2$; the waveguides can be readily prepared for multimode applications by direct UV patterning. The waveguides exhibited smooth surface profiles and a low optical loss of 0.07 ㏈/cm at the most important wavelength (850nm) used for optical interconnects.

• Polymer(Korea)
• /
• v.24 no.5
• /
• pp.673-681
• /
• 2000

Electrically conductive composites have been prepared by treating fabrics with oxidizing agent and exposing them to aniline, which deposited a substantial amount of conductive polymer within the interstices of the material. However the conductivity of the composite fabrics was limited by the irregular deposition of the conductive polymer layer. To improve the conductivity of polyaniline/nylon 6 composite fabrics, we modified the surface characteristics of nylon 6 fabrics by various plasma treatments and increased diffusion and adsorption of aniline by ultrasonic treatments. By the oxygen plasma treatment, attachment of functional groups such as C-O and C-OH increased on the surface of nylon 6 fiber, which promoted adhesion to polyaniline resulting in the higher add-on and electrical conductivity. Electrical conductivities of polyaniline/nylon 6 composite fabrics were highly increased by ultrasonic treatment, which assisted the diffusion of aniline into the inside of nylon fabrics by cavitation and vibration. Also, the effects of monomer concentration and the number of deposition cycles on the nylon 6 fabric conductivity Were investigated. As a result, the fabric conductivity increased with the monomer concentration and the number of polymerization deposition cycles.

• Carbon letters
• /
• v.14 no.2
• /
• pp.117-120
• /
• 2013

In this study, an electro-catalyst of Pt nanoparticles supported by polypyrrole-functionalized graphene (Pt/PPy-reduced graphene oxide [RGO]) is reported. The Pt nanoparticles are deposited on the PPy-RGO composite by chemical reduction of H2PtCl6 using NaBH4. The presence of graphene (RGO) caused higher activity. This might have been due to increased electro-chemically accessible surface areas, increased electronic conductivity, and easier charge-transfer at polymer-electrolyte interfaces, allowing higher dispersion and utilization of the deposited Pt nano-particles. Microstructure, morphology and crystallinity of the synthesized materials were investigated using X-ray diffraction and transmission electron microscopy. The results showed successful deposition of Pt nano-particles, with crystallite size of about 2.7 nm, on the PPy-RGO support film. Catalytic activity for methanol electro-oxidation in fuel cells was investigated using cyclic voltammetry. The fundamental electrochemical test results indicated that the electro-catalytic activity, for methanol oxidation, of the Pt/PPy-RGO combination was much better than for commercial catalyst.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.1
• /
• pp.51-53
• /
• 2008

A new nano-particle deposition system (NPDS) was developed for a ceramic and metal coating process. Nano- and micro-sized powders were sprayed through a supersonic nozzle at room temperature and low vacuum conditions to create ceramic and metal thin films on metal and polymer substrates without thermal damage. Ceramic titanium dioxide ($TiO_2$) powder was deposited on polyethylene terephthalate substrates and metal tin (Sn) powder was deposited on SUS substrates. Deposition images were obtained and the resulting chemical composition was measured using X-ray photoelectron spectroscopy. The test results demonstrated that the new NPDS provides a noble coating method for ceramic and metal materials.

• Current Optics and Photonics
• /
• v.3 no.6
• /
• pp.566-570
• /
• 2019

To investigate dependence of the sensitivity of THz metamaterials on the position of target dielectric materials, we functionalized the metamaterial gap with an adhesive polymer. A shift in resonance frequency occurs when polystyrene microbeads are deposited in the gap of the metamaterial's metal resonator pattern, while little change is observed when they are deposited on other areas of the metasurface. A two-dimensional mapping of the sensitivity, with a grid size of 1 ㎛, is obtained from a finite-difference time-domain simulation: The frequency shift is displayed as a function of the position of a target dielectric cube. The resulting sensitivity distribution clearly reveals the crucial role of the gap in sensing with metamaterials, which is consistent with the electric field distribution near the gap.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.992-995
• /
• 2004

In this study, we have grown indium tin oxide (ITO) thin films by using a low-frequency (60${\sim}$300 Hz) magnetron sputtering method and investigated characteristics of ITO thin films deposited on polyethersulfone substrates. The experimental results show that the films have good qualities in surface morphology, transmittance, and electrical conduction.