• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04a
• /
• pp.49-50
• /
• 2008

OCB mode has advantages such as fast response time and wide viewing angle. But it has inevitable shortcoming which initial splay state must be changed to bend state. To overcoming this problem, OCB cell filled LC with RM monomer was cured by UV when voltage applied. Through previously mentioned methods, even if electric field is none, bend state was made by stabilized LC director. In this paper, we investigated the electric characteristics of polymer stabilized OCB mode.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.04a
• /
• pp.350-354
• /
• 1995

This paper is about impact behavior of cylinder container, made of steel fiber reinforced polymer-impregnated concrete(SFPIC), for intermediate and low level radwaste disposal. In order to obtain the material properties of the SFPIC, steel ball impact tests were done to SFPIC beams and its simulation by finite element method was performed. By using the material properties in finite element impact analysis of the SFPIC concrete cylinder, we obtained impact behavior of the cylinder.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04c
• /
• pp.73-74
• /
• 2008

In this paper, we have investigated dispersibility, volume resistivity of nano-composite by solution mixing method. Dispersibility measured by FE-SEM(Field Emission Scanning Electron Microscope. And volume resistivity measured by ASTM D991. To expect interaction used dual filler system. But, dual filler system had influence on polymer complex. So, polymer chain mobility doesn't resist.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.6
• /
• pp.434-440
• /
• 2013

With polymer properties and ceramic volume fraction as design variables, the optimal structure of 1-3 piezocomposites has been determined to maximize the thickness mode electromechanical coupling factor. When the piezocomposite vibrates in a thickness mode, inter-pillar resonant modes are likely to occur between lattice-structured piezoceramic pillars and polymer matrix, which significantly deteriorates the performance of the piezocomposite. In this work, a new method to design the structure of the 1-3 type piezocomposite is proposed to maximize the thickness mode electromechanical coupling factor while preventing the occurrence of the inter-pillar modes. Genetic algorithm was used for the optimal design, and the finite element analysis method was used for the analysis of the inter-pillar mode.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1993.11a
• /
• pp.109-111
• /
• 1993

We reported the fabrication and thermal cross-linking of the LB files on porous substrates. The monolayers of the polymers which polyion-conplexed with PAA at the air-water interface can be transferred onto solid substrates such as porous fluorocarbon membrane filter and quartz crystal microbalance. The properties of the monolayers and the LB films investigated by $\pi$-A isothem, FT-IR, and SEM will be discussed. In addition, it was attempted to investigate the reaction of polymer LB films in the organic gas surrounding by the use of LB technique.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.6
• /
• pp.481-485
• /
• 1998

We investigated the generation of high pretilt angle for nematic liquid crystal (NLC) in a cell with obilique non-polarized ultraviolet (UV) light irradiation on mixtured polyimide surface. It was found that the monodomain alignment of NLC is obtained with an angle of incidence of 75∼85 degrees on PI surface. We consider that the monodomain alignment of NLC is attributed to anisotropic dispersion force effect to photo-depolymerization of polymer. We successfully observed that the pretilt angle of NLC is generated above 5 degree with an angle of incidence of 75∼85 degrees. It is considered that the pretilt angle generation NLC is attributed to interaction between the LC molecules and the polymer surfaces.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.485-488
• /
• 2001

This paper provides the result of analysis of the structure and I-V characteristics of D.C. 1500 V surge arresters which were installed in railway line currently. As Porcelain housed surge arresters have unstable elements such as exploding and dispersion, so it is thought that the system is protected more stably with replacement of polymer housing. The adoption of gap mitigates the voltage stress which is degradation factor of surge arresters and the research is needed to enhance the life characteristic in additive and manufacturing process. Therefore, it is thought that the research should be continued to develop homemade the surge arresters for D.C. railway line as well as transmission line.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.6
• /
• pp.477-480
• /
• 1998

In this paper, we investigated the liquid crystal(LC) alignment and generation of pretilt angle by using photo-alignment techniques on two kinds of polyimide(PI) surface, It was found that the uniform alignment for nematic(N) LC is obtained in a cell with slanted UV light irradiation on PI surface without side chain. We successfully observed that the pretilt angle of NLC is generated about $3^{\circ}$ with an incident angle of 70 degree on the PI surface without side chain. It is considered that the pretilt angle generation in NLC is attributed to interaction between the LC molecules and the polymer surfaces.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.202-205
• /
• 1997

In this paper, we synthesized poly(N-(2-4-imidazolyl) ethyl) maleimide-alt-1-octadecene(IMI-O) polymer that can have function group and improvement of mechnical strength and then confirmed the possibility of molecular device made by LB method. Evaluation of LB film have been processed such as the technique of EA, $^{1}$H-NMR, FT-IR. Also, the deposition status was observed by SEM and Metal/Insulator/Metal(MIM) device was fabricated for investigation of electric properties. In our experimental results. The surface pressure for the solid state was investigated to 20~35[dyne/cm] by the $\pi$ -A isotherm and the limiting area was about 40 ~45 ($\AA$$^2$/molecule). The deposition status of LB films was confirmed by SEM. The conductivity of LB film was found to be 10$^{-14}$ ~10$^{-13}$ [S/cm] by I-V characteristic.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.261-264
• /
• 1997

Polyphenylenediamine(PPD)film was prepared with organo sulfur compond (2-aminothiophenol, 1,2-ethanedithiol, and 2-aminoethaneethiol etc.) adding lithium salt to increase the electrical conductivity of the polymer surface. The molecular structure of conductive polymer synthesized were examined and discussed by using SEM, FT-IR, NMR etc. The elecrical conductivity messurement were carried out with four-probe method at dry box of He and $N_2$atmosphere. The typical value of successful electrical conductivity was 1.2$\times$10$^1$S/cm at room temperature.