• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.269-272
• /
• 1997

The Lithium ion secondary battery has been developed for high energy density of portable electrical device and electronics. Among the many conductive polymer materials, the positive active film for Li polymer battery system was synthesized successfully from polyphenylene diamine(PPD) by chemical polymerization in our lab. And PPD-DMcT(2, 5-dimercapto-1, 3, 4-thi-adiazole) composite flim conductive material, at high temperature was also prerared with the addition of dimethylsulfoxide(DMSO). The surface morphology and thermal stability of prepared composite flim was carried out by using SEM and TGA, respectively. Electrochemical and electrical conductivity of composite flim were also discussed by cyclic voltammetry and four-probe method in dry box(<27pm). And the electrode reaction mechanism was detected and analyzed from the half cell unit battery system.

• The Korean Journal of Ceramics
• /
• v.5 no.3
• /
• pp.265-269
• /
• 1999

Polyethylene was modified with silanol groups on its surface by photografting of vinyltrimethoxysilane in vapor phase by using benzophenon as a polymerization initiator and by hydrolyzing the methoxysilane groups into the silanol groups with HCI solution. The modified polyethylene formed a dense and homogeneous apatite layer on its surface in a solution with ion concentrations 1.5 times those of human blood plasma within 21 days. This kind of biomimetic process could provide techniques for fabricating apatite-polymer composites with three dimensional structure analogous to the natural bone.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.3
• /
• pp.121-124
• /
• 2007

The $Zn_2SiO_4:Mn$ phosphors were prepared using polymer matrix technique in order to improve the performance of green emitting phosphors for plasma display panel(PDP). $Zn_2SiO_4:Mn$ phosphor exhibits a strong green emission around 520-530 nm. The emission intensity and particle size of powders were controlled by sintering temperature and raw material composition. The zinc silicate $Zn_2SiO_4:Mn$ single phase were obtained at lower temperature than prepared by solid-state reaction method. PL luminance of $Zn_2SiO_4:Mn$ phosphor was similar to the commercial material.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.585-590
• /
• 1997

Conventional foaming process has defects such as lower mechanical properties than ur~foaming material due to non-uniform cell distribution and environmental pollution problem caused by chemical blowing agency. So, a new foaming process such as Microcelluar plastics has been introduced to use inactive gases as a foaming agency. In order to apply Microcellular plastics for mass production process system such as extrusion, injection molding and blow molding, it needs to predict the change in material properties of polymer according to the amount of meltingas. In Polymer molding applying Microcelluar plastics, the change of viscosity among several material properties is the most important factor. Therefore, this paper is aimed to establish the method which not only finds out but also predicts the change of viscosity of ABS(Acrylonitri1e Butadiene Styrene) resin according to inert gas amount in extrusion molding.

• Tribology and Lubricants
• /
• v.25 no.3
• /
• pp.182-186
• /
• 2009

Extruders can be basically divided into bisk and screw type of extruders. Though plastic extruders are often used for its simplicity for water and oil transportation pumps, these days screw extruders are mostly used. Screws are used in many extrusion processes to manufacture complex and complicated shaped parts made of plastics, medicine materials, food, polymer composites, iron and ceramic powders, etc. Also, material correction of deformities is caused by flow and physicochemical reaction phenomenonand material extrusion is processed according to heat transfer. various material comes to hopper because extruder has function by blender and mixing of materials can go well before come out through dice. These change process is so complicated that process condition is decided by trial and error that process condition is underground mainly at extrusion molding process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.199-202
• /
• 1998

In examining application of polymer as electrical insulators, it is very important to perform accelerated aging test substituted the process which polymer insulator is degraded for long-time by the process of short-time. The purpose of this paper is to examine the properties of water degradation which affect on the efficiency of epoxy insulator. To do this, the surface properties on epoxy insulating material have been investigated after long-time accelerated degradation in boiling water condition. The experimental results showed the contact angle and surface resistivity after treatment to decrease the sample of water treatment. In dielectric properties, dielectric constant was increased by the aging development with water treatments.

• Elastomers and Composites
• /
• v.46 no.1
• /
• pp.22-28
• /
• 2011

Various materials are used as electrical barrier materials, such as glass, insulating oil, gas, paper and polymer. These materials shut off electricity from conductor as a barrier and separate as well as support conductor from outside environment while using electrical equipment. Polymers are generally used for cable insulation material. Recently environmental regulation are reinforced and eco-friendly materials are in trend.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.145-148
• /
• 2000

In contrast to the $\pi$ -conjugated polymers which typically absorb light only in the visible spectral region, the $\sigma$-conjugated polymers can be used as efficient material absorbing light in the UV region. In this work, the electronic and optical properties of I$_2$-doped $\sigma$ -conjugated poly (methyl-phenylsilylene) (PMPSi) polymer were investigated. DC conductivity up to 1.2$\times$10$^{-4}$ S/cm was obtained by I$_2$-doping. In UV/Vis absorbance spectrum, a new peak was observed near 370 nm, which was explained by polaron model. The photoluminescence (PL) intensity decreased with increasing degree of I$_2$-doping, and the Infrared (IR) spectrum analysis revealed that the dopants are not directly coupled to the polymer, but effect motions of the methyl and phenyl groups.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.539-540
• /
• 2006

In this paper, We examine that characteristics of formative electret with polymer film and electric charge storage using grid corona discharge. compound polymer of fluorine resin used for material in electret because of high electric charge accumulation, excellent electrical and physical characteristic. All experiments were carried out with circular samples of $Teflon^(R)FEP$ film, 12.5[${\mu}m$] thick. As experiment variables, we used voltage, electrode thickness, discharge electrode gap, and discharge time. According to this variables, we studied on characteristics of formative electret and electric charge storage. Additionally we make a comparative study of the result between the grid corona discharge and needle electrode discharge.

• Journal of Technologic Dentistry
• /
• v.46 no.1
• /
• pp.15-19
• /
• 2024

An ideal post material should have physical properties similar to those of dentin. Post materials with high elastic moduli may cause root fractures. This clinical report describes the treatment of a severely damaged tooth using a recently introduced material. Polyetherketoneketone (PEKK) is a semicrystalline high-performance thermoplastic polymer. PEKK is a promising material for custom post-and-core fabrication because of its elasticity close to that of dentin, good shock absorbance, machinability, and low cost. A laboratory scanner was used to digitize the conventional impression of a severely damaged maxillary right first molar. A custom PEKK post-and-core was designed and milled using computer-aided design and computer-aided manufacturing technology. Using the proposed technique, a custom PEKK post-and-core was fabricated accurately and human error was reduced. Restoration was luted with resin cement. Custom PEKK post-and-core restorations are a viable alternative for treating severely damaged teeth.