• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.1250-1254
• /
• 1992

This paper describes the designed and fabricated thermal imaging system with the SPRITE(Signal PRocessing in The Element) detector, operating in the 3-12 micron band. This system consists of an afocal telescope, a scan unit containing the SPRITE detector, an electronic processor unit and a cooler. The optical scan system utilizing rotating polygon and oscillating mirror, is 2-dimensional serial/parallel scan type using five elements of the detector. And the electronic processor unit performs digital scan conversion to reform the parallel data stream into serial analog data compatable with conventional RS-170 video. The scan field of view is 40 ${\times}$ 26.7 and the MRTD(Minium Resolvable Temperature Difference) is 0.6 K at 7.5 cycles/mm. The acquired thermal image indicates that this system has a satisfactory performance.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.189-193
• /
• 2001

The performance of printer can be determined by the printing speed, noise level, printing quality which includes the resolution, regularity of printed matter and etc. Among them, printing quality mostly depends on the irregularity of the line spacing and dot size. The irregular line spacing and dot size in laser beam printer are mainly from the jitter which comes from the vibration of Organic Photo Conductive(OPC) drum and the Laser Scanning Unit(LSU). Jitter due to the vibration of LSU appears as high-frequency component which occurs 100-300$\mu\textrm{m}$ interval in printed matter and the causes of it can be estimated as the vibration of polygon motor, case, reflecting mirror and etc. In this paper, vibration characteristics of the LSU under development are investigated and the strategy for improvement of the dynamic characteristics is established and its validity is demonstrated.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.168-171
• /
• 2005

The present study describes the prediction of the flow induced noise level of a high-speed rotating hexagonal disk and proposes the way how to reduce it. Since a hexagonal disk, which is used in the laser printer and named a polygon mirror, has six sharp comers, there are low and high pressure regions on each of six edges when it rotates. Therefore, the Pressure difference generates three dimension flow field and causes aerodynamic noise. The Ffowcs-Williams and Hawkings(FWH) method is employed for the analysis. We have measured the sound pressure levels and compared them with the computational results. The calculated sound pressure levels agree well with the experimental results. We modified the shape of the edges of a hexagonal disk to reduce the noise level and confirm their effects through numerical computation.

• Journal of the Optical Society of Korea
• /
• 제15권1호
• /
• pp.22-29
• /
• 2011

We analyze aberrations in an optical laser printer system in order to know how to determine an allowable non-uniformity of the movement of a light spot, how to determine allowed variation of spot sizes, and how to minimize the influence of these deviations on technological errors. In this paper, the correction and the tolerance of distortion are analyzed by using the concept of zonal and global distortions. The tolerance of field curvature is also obtained from Gaussian beam properties. In order to reduce the change of the entrance pupil position and to make a more compact laser printer system the minimum size of the rotator is exactly derived from the geometry with the introduction of the shift angle of the input beam.

• Current Optics and Photonics
• /
• 제2권6호
• /
• pp.595-605
• /
• 2018

The two-photon process of microscopy provides good spatial resolution and optical sectioning ability when observing quasi-static endogenous fluorescent tissue within an in vivo animal model skin. In order to extend the use of such systems, we developed a two-photon laser scanning microscopy system capable of also capturing $512{\times}512$ pixel images at 90 frames per second. This was made possible by incorporating a 72 facet polygon mirror which was mounted on a 55 kRPM motor to enhance the fast-scan axis speed in the horizontal direction. Using the enhanced temporal resolution of our high-speed two-photon laser scanning microscope, we show that rapid processes, such as fluorescently labeled erythrocytes moving in mouse blood flow at up to 1.2 mm/s, can be achieved.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.394-400
• /
• 2008

This paper presents an analytical method to investigate the stability of FDBs (fluid dynamic bearings) considering the tilting motion. The perturbed equations of motion are derived with respect to translational and tilting motion for the general rotor-bearing system with five degrees of freedom. The Reynolds equations and their perturbed equations are solved by using the FEM in order to calculate the pressure, load capacity, and the stiffness and damping coefficients. This research introduces the radius of gyration to the equations of notion in order to express the mass moment of interia with respect to the critical mass. Then the critical mass of FDBs is determined by solving the eigenvalue problem of the linear equations of motion. This research is numerically validated by comparing the stability chart of FDBs with the time response of the whirl radius obtained from the direct integration of the equations of motion. This research shows that the tilting motion is one of the major design considerations to determine the stability of rotating system. It also shows that the stability of FDBs considering only translation is overestimated in comparison with the stability of FDBs considering both translational and tilting motion.

• 한국광학회지
• /
• 제10권5호
• /
• pp.364-368
• /
• 1999

일반적으로 LSU(Laser Scanning Unit)는 LD모듈(Laser Diode, 콜리메이팅 렌즈, 슬릿), 실린더 렌즈 고속회전하는 PM(Polygon Mirror), f$\theta$렌즈와 같은 광부품들과 이들을 취부하는 Housing으로 구성되어져 있다. 먼저 본 논문에서는 당사에서 자체적으로 광설계된 LSU 시작품(시작(試作品)을 측정/평가하기 위해 평가항목들에 관해 살펴 보았다. 당사에서 시제작된 LSU의 특징은 LSU의 핵심부품인 f$\theta$렌즈가 2단가압형 저압사출방식으로 제작되었다는 것이다. LSU의 평가항목들은 BSH(Beam Scan Head)를 LMC(Linear Motion Controller)위에 장착해서 비교적 간단히 측정 할 수 있었고, 측정결과 600DPI(Dots Per Inch) 성능을 만족함을 확인할 수 있었다.

• Journal of the Optical Society of Korea
• /
• 제13권2호
• /
• pp.251-255
• /
• 2009

In the non-contact 3-dimensional (3D) shape measurements, the fringe pattern projection method based on the phase-shifting technique has been considered very effective for its high speed and accuracy. The digital fringe projector in particular has great flexibility in generating fringe patterns since the patterns can be controlled easily by the computer program. In this work, we have developed a high-speed digital laser grating projection system using a laser diode and a polygon mirror, and evaluated its performance. It has been demonstrated that all the optical measurements required to find out the profile of a 3D object could be carried out within 31 ms, which confirmed the validity of our 3D measurement system. The result implies the more important fact that the speed in 3D measurement can be enhanced remarkably since, in our novel system, there is no device like a LCD or DMD whose response time limits the measurement speed.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1995년도 춘계학술대회 논문집
• /
• pp.1-8
• /
• 1995

This paper proposed a simple method for measuring surface roughness of ground surface. utilizing non-contact in-process measuring system using the diode laser. The measurement system is consisted of a laser unit with a diode laser and a cylindrical lens a detecting unit with polygon mirror and CCD array sensor. and a signal processing unit with a computer and device. During operation, this measuring system can provide information on surface roughness in the measuring distance with a single sampling and simultanilusly monitor the state of the grind wheel. The experimental results, showed that the increase of the feed rate and the dressing speed an caused increase in the surface roughness and when the surface roughness is 4Rmax-10Rmax, the cutting speed is 1653m/min-1665m/min. the feed rate is 0.2m/min-0.9m/min, the dressing speed is 0.2mm/rev-0.4mm/rev, the stylus method and the in-process method can be obtained the same results. thus under limited working conditions. using the proposed system. the surface roughness of the ground surface during cylindrical grinding can be obtained through the in-process measurement method using the diode laser.

• 한국정밀공학회지
• /
• 제27권7호
• /
• pp.94-100
• /
• 2010

This paper describes the design and evaluation procedure of an ultra-precision rotary table for freeform generating machined tools. Design of the thrust and journal hydrostatic bearings and experimental evaluation of the table were performed. To get the compact size and less lost motion direct drive servomotor with ultra precision encoder. From the considered design, following performance were confirmed by experiment. The total stiffness of the prototype rotary table was 483.6 $N/{\mu}m$ and 97.6 $N/{\mu}m$ for axial and radial direction, respectively. Rotational accuracy of the table was investigated by capacitive sensor and reversal measurement technique, and 0.10 ${\mu}m$ radial direction and 0.05 ${\mu}m$ axial direction of the rotational accuracy were confirmed. The micro resolution of the table was also investigated with displacement of capacitive sensor, and $0.5/10000^{\circ}$ of micro resolution was confirmed. Index accuracy of the table was evaluated by the autocollimator and polygon mirror, and the $\pm0.39$ arcsec accuracy and $\pm0.16$ arcsec repeatability of the table were confirmed. Those are under the general requirements of ultra precision rotary tables for freeform generating machined tools.