• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.32 no.2
• /
• pp.153-162
• /
• 2022

Objectives: Fused deposition modeling (FDM) 3D printer which is one of the material extrusion (MEX) technologies is an additive manufacturing (AM) process. 3D printers have been distributed widely in Korea, particularly in school and office, even at home. Several studies have shown that nanoparticles and volatile organic compounds (VOCs) were emitted from an FDM 3D printing process. The objective of this study was to identify types of chemicals possibly emitted from FDM 3D printing materials such as PLA (polylactic acid), ABS (acrylonitrile butadiene styrene), nylon, PETG (polyethylene terephthalate glycol), PVA (polyvinyl alcohol), PC (polycarbonate) filaments. Methods: 19 FDM 3D printing filaments which have been distributed in Korea were selected and analyzed VOCs emitted of 3D printing materials by headspace gas chromatography mass spectrometry (headspace GC-MS). Subsamples were put into a vial and heated up to 200℃ (500 rpm) during 20 minutes before analyzing FDM 3D printing filaments. Results: In the case of PLA filament, lactide and methyl methacrylate, the monomer components of one, were detected, and the volume ratio ranged 27~93%, 0.5~37% respectively. In the case of ABS filaments, styrene (50.5~59.1%), the monomer components of one, was detected. Several VOCs among acetaldehyde, toluene, ethylbenzene, xylene, etc were detected from each FDM 3D printing filaments. Conclusions: Several VOCs, semi-VOCs were emitted from FDM 3D printing filaments in this study and previous studies. Users were possibly exposed to ones so that we strongly believe that we recommend to install the ventilation system such as a local exhaust ventilation (LEV) when they operate the FDM 3D printers in a workplace.

• Journal of Marine Bioscience and Biotechnology
• /
• v.14 no.2
• /
• pp.133-142
• /
• 2022

The increased production and consumption of polyethylene terephthalate (PET)-based products over the past several decades has resulted in the discharge of countless tons of PET waste into the marine environment. PET microparticles resulting from the physical erosion of general PET wastes end up in the ocean and pose a threat to the marine biosphere and human health, necessitating the development of new technologies for recycling and upcycling. Notably, enzyme-mediated PET degradation is an appealing option due to its eco-friendly and energy-saving characteristics. PETase, a PET-hydrolyzing enzyme originating from Ideonella sakaiensis, is one of the most thoroughly researched biological catalysts. However, the industrial application of PETase-mediated PET recycling is limited due to the low stability and poor reusability of the enzyme. Here we developed the whole-cell catalyst (WCC) in which functional PETase is attached to the outer membrane of Escherichia coli. Immunoassays are used to identify the surface-expressed PETase, and we demonstrated that the WCC degraded PET microparticles most efficiently at 30℃ and pH 9 without agitation. Furthermore, the WCC increased the PET-degrading activity in a concentration-dependent manner, surpassing the limited activity of soluble PETase above 100 nM. Finally, we demonstrated that the WCC could be recycled up to three times.

• Journal of Sensor Science and Technology
• /
• v.31 no.2
• /
• pp.90-95
• /
• 2022

The effect of the structure of an ITO nanoparticle film sensor on its performance was studied. A printed ITO film (P-ITO film) was fabricated on a flexible polyethylene terephthalate (PET) substrate, and the contact resistance of the electrode and sensor response change were clarified according to the detection position. The contact resistance between Ag and P-ITO was observed to be -204.4 Ω using the transmission line method (TLM), confirming that a very good ohmic contact is possible. In addition, we confirmed that the contact position of the analyte had a significant influence on the response of the sensor. Based on these results, the performance of the four types of sensors was compared. Consequently, we observed that 1) optimizing the resistance of the printed film, 2) optimizing the electrode structure and analyte input position, and 3) optimizing the electrode area are very important for fabricating a metal oxide nanoparticle (MONP) sensor with optimal performance.

• Textile Coloration and Finishing
• /
• v.35 no.2
• /
• pp.128-136
• /
• 2023

Recently, the automobile industry is developing as the demand for automo- biles increases due to industrial development and population growth. In addition, many studies are being conducted to reduce heat loss inside the automobiles in order to save energy inside the automobiles due to environmental regulations. In this study, alumina, nanosilicon, and aerogel, which are adiabatic materials, were filled in PET to manufacture yarn, identify physical and mechanical properties, and weave into fabric to confirm adiabatic performance. As the content of the adiabatic material increased, the tensile strength of the fibers filled with alumina and nanosilicon decreased greatly, and the adiabatic property slightly increased. The tensile strength of fibers filled with the aerogel decreased slightly, but the adiabatic properties were greatly increased. Therefore, it is considered to be due to the large volume fraction in the PET yarn due to the low density of the aerogel.

• Asia Marketing Journal
• /
• v.14 no.3
• /
• pp.169-184
• /
• 2012

All firms require new stimulus to spurt growth. Therefore it is necessary to successfully develop new products and to employ appropriate marketing practices for the new products to enter and settle in the market. Binggrae, a Korean company that specializes in dairy and processed dairy products, introduced a ready-to-drink (RTD) coffee product, 'a Café la' to expand its business into the coffee market in 2008. Binggrae was a latecomer in the RTD coffee market but a Café la has shown an impressive average sales growth rate of 115% as of 2011 since the launch. Moreover, it is a steady bestselling coffee brand among the Polyethylene terephthalate (PET)bottle category. Binggrae found potential and opportunity in the growing coffee market and made efforts to develop a new product that can be differentiated from the existing products. The result was PET bottle coffee, which was more portable and convenient to drink than coffee products offered in cups or cans. PET bottle coffee is produced through the patented Aseptic Filing System, thus the original coffee flavor stays fresh when combined with milk and has a longer shelf life than coffee products in cups. Moreover, as the taste of coffee consumers has become more sophisticated, Binggrae developed a premium product by differentiating the product processing method and by using higher-quality Arabica beans. After launching the new product, the company also employed a well-designed communication strategy. First, Binggrae was able to confirm the level of market demand and market potential for the product by employing BTL (Below the Line) marketing strategies through the consumers' word-of-mouth. Afterwards, the company invested its resources for a full-scale ATL (Above the Line) marketing campaign. Later a Café la's TV commercial effectively portrayed the product's characteristics, and succeeded in raising consumer awareness of the product. As a result, a Café la has become the bestselling brand in the PET bottle coffee market. The successful new product marketing strategy of Binggrae'sa Café la offers many valuable implications for companies planning to launch new products in the future.

• Fashion & Textile Research Journal
• /
• v.25 no.5
• /
• pp.651-660
• /
• 2023

This study aimed to research the local production of conductive composite yarn, a source material used in textile-type electrodes and circuits. The physical properties of an internationally available conductive composite yarn were analyzed. To manufacture the conductive composite yarn, we selected one type of conductive yarn with Ag-coated polyamide of 150d 1 ply, along with two types of polyethylene terephthalate (PET) with circular and triangular cross-sections, both with 150d 1 ply. The conductive composite yarn samples were manufactured at 250, 500, 750, and 1000 turns per meter (TPM). For both conductive composite yarn samples manufactured from two types of PET filaments, the twist contraction rate of the sample with a triangular cross-section was stable. Among the samples, the tensile strength of the sample manufactured at 750 TPM was the highest at approximately 4.1gf/d; the overall linear resistance was approximately 5.0 Ω/cm, which is within the target range. It was confirmed that the triangular cross-section sample manufactured with 750 TPM had a similar linear resistance value to the advanced product despite the increase in the number of twists. In future studies, we plan tomanufacture samples by varying the twist conditions to derive the optimal conductive yarn suitable for smartwear and smart textile manufacturing conditions.

• Tribology and Lubricants
• /
• v.39 no.6
• /
• pp.235-243
• /
• 2023

This paper presents the fabrication process of water-lubricated plastic bearings. Plastic bearings require good mechanical properties and tribological properties as well as elasticity and shock resistance, especially when lubricated in dirty water conditions. In this study, sleeve-type plastic bearings are produced by winding a prepreg sheet, which primary contains nitrile rubber (NBR)-modified epoxy, self-lubricating fillers, and various types of lattice-structured reinforcing fibers such as carbon, Aramid, and polyethylene terephthalate. A thermosetting epoxy is chemically modified with NBR to impart elasticity and low-friction characteristics in water conditions. Experimental investigations are conducted to examine the mechanical and tribological characteristics of the developed bearing materials, and the results are compared with the characteristics of a commercial plastic bearing (Thordon SXL), well known as a water-lubricated bearing. A Thordon bearing (mainly composed of polyurethane) exhibits an extremely low load-bearing capacity and is thus only suitable for medium loading (1~10MPa). The tribological characteristics of the test materials are evaluated through Falex block-on-ring (LFW-1) friction and wear tests. The results indicate that friction exhibited by the carbon-fiber-reinforced NBR-10wt.%-modified epoxy composite material, incorporated with the addition of 20wt.% UHMWPE and 6wt.% paraffin wax, is lower than that of the Thorden bearings, whereas its wear resistance surpass that of Thorden ones. Because of these features, the load carrying capacity of the fabricated composite (>10MPa) is higher than that of the Thorden bearings. These results confirm the applicability of water-lubricated plastic bearing materials developed in this study.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.34 no.1
• /
• pp.16-21
• /
• 2024

Using electrochromic devices (ECD), smart window films that can change the colors from tinted state into transparent state by applying an external voltage were manufactured. Polyethylene terephthalate (PET) film was used as a substrate instead of conventional glass, and ECD modules having a total thickness of about 50 ㎛ were manufactured by sequentially introducing an ITO/Ag/ITO electrode layer, a WO3/TIC2 organic discoloration layer, and a Nafion fluorine electrolyte layer. Through a series of sputtering, bar coating, and thermal compression processes, a large scale smart window with a horizontal and vertical length of more than 80 mm was manufactured. When DC 3.5 V was applied, the transmittance decreased from 54 % to 24 % and moreover the color change could be confirmed even with the naked eye. Reversible color change capability at low external voltage implies that external sunlight can be selectively blocked which is effective in terms of energy saving.

• Design & Manufacturing
• /
• v.18 no.2
• /
• pp.17-22
• /
• 2024

Lightweight of plastic containers is becoming an important issue due to increasing environmental legislation and consumer awareness. In this study, the CAE analysis was conducted to optimize the shape of a 500 ml lightweight square polyethylene terephthalate(PET) bottle. First, the linear buckling alaysis using the finite element method was performed to analyze the correlation between the primary geometric parameters of the bottle and the buckling critical load. Then, the optimal geometry parameters were derived, and the actual buckling load was predicted by non-linear buckling simulation. The validity of the simulation results was verified by top-loading tests of PET bottles molded with the optimized geometry. The elastic modulus and tensile yield strength of PET through tensile tests were measured to improve the accuracy of the simulation. As a result of the tensile tests, the modulus of elasticity of PET increased from 2,900 MPa to 4,275 MPa, and the tensile yield strength increased from 52.4 MPa to 88.1 MPa. Finally the buckling load of the optimized PET bottle was found to be approximately 236 N, which is very similar to the simulation precition of 238 N. This study shows the feasibility and accuracy of the CAE analysis approach for the lightweight design of PET bottles, and will provide useful guidelines for the design of PET bottles.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.9
• /
• pp.946-951
• /
• 2005

In this wort plasma treatment was evaluated as an alternative clean desizing technology. Size materials such as PVA(polyvinyl alcohol), PACL(polyacrylic acid esters) and their mixture on PET(polyethylene terephthalate) fabrics were treated by $N_2$ and $O_2$ plasma. $O_2$ plasma was more efficient in size removal than $N_2$ plasma, and the removal of PVA was higher than that of PACL. SEM(scanning emission microscopy) pictures of the plasma treated samples directly proved the disappearance of sizing agents. After $O_2$ plasma treatment, the PET fabrics were subjected to conventional desizing process. Compared with untreated fabrics, the desizing effluent from the treated fabrics gave lower TOC, COD and $BOD_5$ values. This indicates plasma treatment not only serves to directly remove sizing agents but also offered several advantages by changing the chemical properties of sizing agents. Lastly, the effect of plasma desizing process on dyeing was examined using color difference and dyeing fastness tests. The CCM(computer color matching) results showed rotor difference between PET fabric desized by $O_2$ plasma treatment for 20 min and reference PET fabric desized by the conventional wet desizing process was around 1. This suggests the treated PET fabric can be directly subjected to dyeing process without any additional process. The plasma treated fabric also gave a good result of dyeing fastness so that grades of laundering, crocking, heat and light fastness were same or even better than the reference PET fabric did.