How to stabilize wood against shrinking and swelling in variable atmospheric moisture conditions is important to the wood-using industry and a challenge to research. Polyethylene glycol stabilize wood by bulking the fiber. PEG also serve as a chemical seasoning agent, suppress decay in high concentrations, and have slight effect on physical properties, gluing or finishing. The study designed to determine the effect of PEG-400 on the dimensional stabilization of local hardwoods for wood carvings that could supply a greatly expanding tourist trade and making curved furniture parts, lamp stands and other decorative objects, and possible gunstock. The species examined were 6 species, Seo-Namoo (Carpinus laxiflora), Cheungcheung-Namoo (Cornus controversa), Gorosae-Namoo (Acer mono), Karae-Namoo (Juglans mandshurica), Jolcham-Namoo (Quercusserrata) and Sanbud-Namoo (Prunus sargentii), used as block of 5cm thick radially to the grain, 7cm wide tangentially, and 70cm long parallel to the wood grain. All these test piecies were conditioned above the fiber saturation point before impregnation. The stabilization effects were determined for PEG-400 treated woods in a 50 percent solution for 20 days. The following conclusions were obtained. PEG retentions increased with treating time. It was more effective to treat at 60$^{\circ}C$ than at room temperature. In degree of PEG-400 impregnation on species, Cheungcheung-Namoo havinglow specific gravity had the highest retentions, 68.77% but the lowest, 56.33% was shown in Jolcham-Namoo with high specific gravity. Specific gravity of treated wood increased considerably with effectiveness of polymer loading. The increases in specific gravity were 5.36 to 13.16 percent. The highest was Jolcham-Namoo, the lowest Karae-Namoo. On the dimensional stability, a 40 percent of effectiveness of polymer loading was just as effective as 60 percent in reduction in water absorptivity (RWA), antishrinkage efficiency (ASE) and antiswelling efficiency (AE), and from over 60 percent they increased more rapidly. Also species response varied considerably. ASE was 30.12 to 69.97 percent tangentially and 27.86 to 56.37 percent radially, AE 34.06 to 73.76 percent tangentially and 30.11 to 70.12 percent radially, and RWA 42.31 to 65.32 percent. No differences in volume swelling among the 6 species were observed. Its values were ranged from 14.98 to 19.55 percent and also increased with PEG retentions. On the mechanical properties, the strengths very much decreased with PEG-400 loadings as shown in Figure 12; that were 11.41 to 22.90 percent in compression, 21.61 to 34.35 percent in bending and 22.83 to 36.83 percent in tensile strength. PEG retention in cell wall was less than 1 percent and the most of PEG were immersed in cell lumen. Except for Korae-Namoo, effectivenesses of polymer loading were as much high as 61.58 to 75.02 percent. This is believed to be due to the effect of PEG-400 on excellant dimensional stability of treated woods.
Classified handmade Korean paper which has been commonly used as the material for the paper cultural assets divide into four classes. We irradiated xenon arc lamp, which has almost the same spectrum distribution as natural sunlight, to test photo-induced of discoloration according to PEG molecular weight and concentration. So, we reach the followings. 1) Unbleached handmade Korean paper with PEG showed rapid decrease of brightness for 10 hours after photo-irradiation, regardless of molecular weight of PEG, but, after 10 hours, it showed gradual increase of brightness. From this, it proved that there was an effect of preventing discoloration of photo-irradiation. 2) Chemical bleached handmade Korean paper showed increase of brightness after 20 hours. Though time was delayed in increase of brightness, there was also an effect of preventing discoloration of photo-irradiation in chemical bleached paper. 3) Handmade Korean paper made with abet-mosk showed the lowest of brightness when it was tested on 400-20% PEG. Before photo-irradiation, the brightness of paper, applied it, was the lowest, but it showed the least difference of brightness after photo-irradiation. From this, it proved that there was the greatest effect of preventing discoloration in this paper. 4) Preventing yellowish, the first phenomena by photo-irradiation ageing with applying PEG was proved that there was the decrease of value of $b^*$ +, and increase value of $L^*$, which could fairly prevent decrease of brightness.
Park, Hye-Su;Cho, Bong-Sang;Yoo, Eui-Sang;Ahn, Jae-Beom;Noh, Si-Tae
Applied Chemistry for Engineering
/
v.22
no.4
/
pp.384-389
/
2011
We made suspension of fumed silica in polyethylene glycol (PEG), studied rheological behavior as functions of contents of silica, dispersion condition, PEG molecular weight, temperature and contents of humidity. Rheological behavior of suspension was determined critical shear rate and rise of viscosity using rheometer AR2000. Suspension were PEGs of molecular weight 200, 400, and 600. Fumed silica suspensions of which silica contents are 5, 7, 9, 13, and 18% were prepared by normal mixing, homogenization and bead milling process. We observed their rheological behaviors at 10, 20, 30, and $40^{\circ}C$. As the PEG molecular weight and contents of silica increase, the critical shear rate was lowered. As the temperature increased, the critical shear rate was increased. Humidity contents of dispersion don't influence on the critical shear rate, but dispersion processes greatly affect the critical shear rate. The critical shear rate of suspensions prepared by the mixing process was the lowest, and that of suspensions prepared by the bead milling process was the highest. The rise in the shear viscosity of suspensions prepared by the mixing process is higher than that of suspensions prepared by the bead milling process. This was dependent on the dispersion condition of silica particle by dispersion process.
We investigated the effect of polyethylene glycol(PEG) treatment of preservative treated green japanese cedar(Cryptomeria japonica) round posts on their preservative penetration and check formation during the air drying. The round rods were dip-treated in 10% preservative solution of Basilit CFK for 1 day, followed by application(3, 5, and 10 times) with 50% PEG-400 solution, and then dried for 30 days under natural conditions. The rate of preservative penetration into sapwood was a low by 23.2% without PEG treatment, whereas that was a high by about 51.2~64.5% with PEG treatment. From these results, it was assumed that PEG played an affirmative role in the penetration of preservative components loaded onto the surface of round rods by dipping. During the air drying, the formation of drying checks decreased significantly with increasing application times of PEG. Even though some drying checks in PEG treated rods were developed, the number and size of checks was reduced remarkably by PEG treatment. After 2 months of outdoor exposure, PEG treatment failed to reduce checking in preservative-treated rods whereas finishing of polyurethane resin lacquer after PEG treatment was significantly effective in preventing check development.
Eun Min Shin;Yeong Eun Joo;Su Min Jung;Jaechan Suh;Chang-Joon Kim
Clean Technology
/
v.29
no.2
/
pp.109-117
/
2023
The purpose of this study is to develop a method for separating antioxidants and sugars from grape skin extract. The extract was first mixed with a variety of organic solvents to investigate whether the separation was feasible. When employing acetone, ethanol, dimethylsulfoxide, or dimethylformamide, the organic solvent-extract combination formed a single phase. However, when benzene, ethyl acetate, or n-hexane was added to the extract, the mixture separated into an organic and an aqueous phase and the pigments remained in the aqueous phase. On the other hand, when polyethylene glycol-2,000 (PEG-2000) and sodium citrate were added to the extract, the mixture was separated into three layers, with the majority of the flavonoids migrating to the top layer and 53% of the extract's glucose migrating to the bottom layer. The top layer had significant antioxidant activity, whereas the bottom layer showed no antioxidant activity. The glucose recovery in the bottom layer increased as the molecular weight of PEG increased and the highest recovery (67%) was observed when PEG-8,000 was added. The highest flavonoid separation was observed with PEG-2,000, followed by PEG-8,000 and PEG-400. The flavonoid separation when PEG-2,000 was added resulted in a flavonoid recovery of 48% and 0.2% from the top and bottom layers, respectively. Examining the effect of the separated solution using the agar disc diffusion method on yeast cell growth confirmed that the addition of the extract, the top, and the bottom layer did not inhibit cell growth.
We studied on preparation of nanoparticles modified surface using biodegradable polymer, poly(DL-lactide-co-glycolide) (PLGA). Two kinds of PLGA nanoparticles were prepared by a spontaneous emulsification solvent diffusion (SESD) method using cetyltrimethylammonium chloride (CTAC) and tetradecyltrimethylammonium bromide (TTAB) as a cationic surfactant and polyethylene glycol-block-polypropylene glycol copolymer (Lutrol F68) as a nonionic surfactant. Model protein was coated on the surface of nanoparticles by the ionic complexation. The model protein was that influenza vaccine ($H_3N_2,\;H_1N_1$, B strain) labeled with NHS-fluorescein. The sizes of cationic nanoparticles were 140-160 nm and the surface charges were 50-60 mV. The sizes of nonionic nanoprticles were 80-90 nm and the surface charge was -10 mV. After coating vaccine on the surface of nanoparticles, the sizes of cationic nanoparticles were increased to 380-400 nm and the size of nonionic nanoparticles was not increased. The amount of coated vaccine on the cationic nanoparticles was 22.73 ${\mu}g$/mg.
To develop a novel transdermal delivery system of loxoprofen (LP), a potent antiinflammatory and analgesic agent, the effects of various vehicles and penetration enhancers on the skin permeation of LP from solution formulations were investigated. The permeation rate of LP through excised guinea pig skin was measured using a side-by-side permeation system at $32^{\circ}C$. The solubilities of LP in various vehicles were determined by the equilibrium solubility method, and partition coefficients $(P_c)$ were determined. The solubility of LP increased in the rank order of water & isopropyl myristate (IPM) & glyceryl dicaprylate/dicaprate & propylene glycol dicaprylate/caprate & propylene glycol laurate (PGL) & polyethylene glycol 400 & diethylene glycol monoethyl ether (DGME) & ethanol. n-Octanol-water $P_c$ value was 15.5. Among pure vehicles tested, IPM and PGL showed highest fluxes of $89.9{\pm}5.0$ and $45.4{\pm}0.3\;{\mu}g/cm^2/hr$ from saturated solutions, respectively. However, it was not possible to demonstrate any correlation between the solubility of LP and its permeation rate, indicating the change in the barrier property of the skin and/or carrier mechanisms by vehicles tested. The addition of DGME to IPM or PGL markedly increased the solubility of LP, but the permeation rate did not decrease when the concentration of DGME in the cosolvent was increased upto 40%. The addition of linoleic acid (3%) in the cosolvent slightly increased the permeation rate, but others such as lauroyl sarcosine, fatty alcohols and fatty acids tested did not show enhancing effect. In conclusion, the DGME-IPM or DGME-PGL cosolvent system proved to be a good vehicle to enhance the skin permeation of LP.
The objective of the research was to investigate the effect of polyethylene glycol (PEG) or urea supplementation in sheep and goats fed a basal diet of Acacia saligna and wheat straw. The 3 dietary treatments were: (1) Control: ad libitum A. saligna+ 400 g/d wheat straw (95% DM) (basal diet); (2) Basal diet+50 g/d PEG 4000; and (3) Basal diet+1% (on a DM basis) urea sprayed onto the straw and A. saligna 30 min prior to feeding. All animals maintained live weight, regardless of the dietary treatment. All sheep readily consumed the A. saligna in preference to straw. In sheep both DMD and OMD were higher (p<0.05) where PEG was included in the diet compared to the other two treatments. Contrary to findings by other researchers there was no significant difference in DMI, DMD or OMD between sheep and goats in corresponding treatment groups. All animals were in positive N balance. For both sheep and goats, rumen ammonia concentrations were increased with the use of either urea or PEG. In these groups the maximum ammonia concentrations exceeded 50 mg/L, considered the minimum required to maximise microbial growth. This threshold, however, was exceeded only for a period of 8-11 h. Of those measured, rumen ammonia levels were generally the highest at 4 h post feeding. None of the measurements of rumen ammonia for the control group approached 50 mg/L. It is unclear how and why feed intake and live weight were maintained when rumen ammonia levels were often sub-optimal.
Yang, Joo Hwan;Han, Joon Taek;Oh, In Ho;Park, Geum Duck
Journal of the Korean Society of Food Science and Nutrition
/
v.44
no.2
/
pp.260-267
/
2015
We investigated the applicability of polyethylene glycol (PEG) as a plasticizer in enteric-coated soft capsules based on determination of quality characteristics according to molecular weight and concentration of enteric-coating PEG solution. There was no difference according to molecular weight of PEG, whereas a low PEG concentration in the enteric-coating solution was associated with higher whiteness index and slower disintegration time in pH 6.8 media. Brittleness was observed in the coating film at seam areas in 5% PEG enteric-coating solution after 2 weeks of storage at room temperature. The enteric-coating properties of PEG were compared with those of acetylated monoglyceride (AMG) and triacetin, which are enteric-coating plasticizers. Enteric-coated soft capsule containing PEG as a plasticizer showed a lower whiteness index and faster dissolution profile than AMG and triacetin. Moreover, enteric-coated soft capsule containing AMG and triacetin as plasticizers showed coating film brittleness at seam areas after 2 months of accelerated storage [$40^{\circ}C$, relative humidity (RH) 75%] but no difference at room temperature storage ($25^{\circ}C$, RH 60%). The present study suggests that concentration of PEG is important to determine enteric-coating quality, regardless of the molecular weight of PEG. In conclusion, PEG has potential as a plasticizer due to its transparency and storage stability in enteric-coated soft capsules.
Organic/inorganic composite electrolyte membranes were prepared for dye sensitized solar cell (DSSC). Poly (ethylene glycol) (PEG)s with various molecular weight (600, 1,500, 2,000 and 3,400) were ethoxysilated to fabricate organic/inorganic composite materials through sol-gel processes. The electrolyte membranes were produced by doping the composite materials with KI and $I_2$, and their ionic conducting behaviors were investigated. The ionic conductivity of the composite membrane was highly affected by PEG molecular weight. The highest conductivity was shown by the composite membrane prepared with PEG with the molecular weight of 2,000. The composite electrolyte membranes showed considerable improvement of ionic conductivity. Compared to PEO electrolyte membranes, the composite electrolyte membrane by PEG, MW 2,000 showed much higher ionic conductivity.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.