• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 춘계학술대회 논문집
• /
• pp.515-516
• /
• 2009

• 한국정밀공학회지
• /
• 제21권1호
• /
• pp.109-115
• /
• 2004

Polishing process has been applied to get extremely fine surfaces, e.g., mirror surfaces such as optical mirrors, lens, molds and etc. Nowadays not only fine surface quality but also submicron order of dimensional accuracy is required for many applications. To meet the requirements polishing process should be provided with an active control of polishing pressure especially for automation of polishing process. In this paper a study on development of an active polishing pressure control system has been presented. A new type of tool assembly has been developed to facilitate the control. The tool is attached to an axis of a polishing machine with a coil spring and control of the polishing pressure is done by the position control of the axis, which needs no additional actuator. The polishing pressure is successfully measured by the measurement of the spring deformation. Control specifications were quantitatively considered by weighting functions and a controller was designed by using loop-shaping technique based on the no synthesis. Some experiments have been executed on a polishing machine with a PC-NC controller. It is shown that the results were coincident well with the theoretical analyses and satisfied the design specifications.

• Journal of the Optical Society of Korea
• /
• 제15권4호
• /
• pp.394-397
• /
• 2011

For the purpose of fabricating off-axis aspheric optics, we propose an 8-axis-polishing machine combined with a testing tower whose height is up to 9 m. The proposed polishing machine was designed and analyzed by using a well-known finite element method. The eight axes of the machine have a synchronized motion generated by a computer, and each axis was calibrated by a heterodyne laser interferometer or an optical encoder. After calibration, the maximum positioning error of the machine was less than 2 ${\mu}m$ within a whole 2 m ${\times}$ 2 m area. A typical fabrication result of a ${\phi}1.5$ m concave mirror was also described in this manuscript.

• 한국기계가공학회지
• /
• 제19권8호
• /
• pp.110-116
• /
• 2020

Aircraft hydraulic oil reservoirs made with aluminum 7075 have an anodized coating to enable airtightness and corrosion resistance. To maintain a stable oil pressure, the internal surface roughness of the reservoir should be less than approximately 0.2 ㎛. To this end, precision polishing must be performed. However, ensuring the processing quality is challenging, as most polishing operations are performed manually, owing to which, the inner surface roughness is not uniform, and the product quality is irregular. Therefore, we developed a special superfinishing machine to realize the efficient inner polishing of an aircraft hydraulic oil reservoir, by using an abrasive film to improve the process throughput and uniformity. In the experiment involving the superfinishing of an anodized aluminum 7075 cylinder specimen by using the proposed machine, a higher surface roughness than that achieved in the repetitive manual polishing process could be realized.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.38-42
• /
• 2002

In the recent, electro-rheological fluid has been used for micro polishing of the 3-dimensional micro-aspherical lens and some sectional parts with defects on the wide flat wafer. The ER fluid has the properties that its viscosity has drastic changed under some electric fields. Therefore, ER fluid can be applicable to the micro polishing fur some parts using these properties. In this paper, the experimental device has been constructed using the precision milling machine in order to micro polishing far some sectional parts of a 4 inches wafer It is consisted of a small steel electrode, a wafer fixture, DC10mA and 5KV power supply unit, and a controller unit. Using the ER experimental device, possibility of amending for wide flat wafer and micro polishing of some micro part has been analyzed.

• 한국생산제조학회지
• /
• 제19권4호
• /
• pp.455-461
• /
• 2010

Automated magnetic abrasive polishing which can be applied after machining of the mold on a machine tool without unloading is very effective for finishing a complicated injection mold surface. This study aims to realize one step polishing of free form surface with the same machine tool. For this purpose, magnetic flux density according to the change of curvature radii was simulated for selecting polishing conditions and experimental verification was performed with a complicated mold of aluminum alloy. As a result, it was seen by the simulation that the magnetic flux density at a gradual curvature of the mold was higher than at a steep curvature and the higher magnetic flux density produced the better surface roughness in the experimentation. The deviation for the surface roughness of the mold decreased on the whole and the uniform mold surface was obtained after the automated magnetic abrasive polishing.

• 한국생산제조학회지
• /
• 제23권6호
• /
• pp.547-554
• /
• 2014

CVD SiC is a perfect material used for molds/dies in hot press molding of glass lens. In its fabrication process, nano-precision polishing is essential finally. For this purpose, a novel polishing method using MCF (Magnetic Compound Fluid) slurry is proposed. In this method, MCF slurry is supplied into a given gap between the workpiece and a MCF slurry carrier, and constrained within the polishing zone by magnetic forces from permanent magnet. In this paper, after an experimental rig used to actually realize the proposed method has been constructed, the fundamental polishing characteristics of CVD SiC such as the effects of process parameters including MCF slurry composition on work-surface roughness were experimentally investigated. As a result, nano-precision surface finish of CVD SiC was successfully attained with MCF slurry and the optimum process parameters for obtaining the smoothest work-surface were determined.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.625-631
• /
• 2002

In the previous study, a polishing robot system was developed to automate the polishing process and to cope with the shortage of skilled workers. This polishing robot system has several advantages: reduced time for setting polishing work, decreased labor costs, effective operation, continuous polishing work without an operator, improved machine accuracy, and the ability to polish a free curved surface die. However, still the problem remains that a worker must stay to monitor the polishing process in the poor working conditions for a long time. Nowadays some advanced manufacturing companies need to find a way to check the performance of their production equipments and plants from remote sites. Thus, this study constructed the communication network and developed the monitoring programs (a servo program and a client program) to operate the polishing robot from remote sites. Using these programs, workers are able to monitor and control the polishing robot on the web page, in any place where internet service is possible. To guarantee a stable operation in spite of a variable computer operating environment, the monitoring system is implemented in Java. The experimental results showed that the developed monitoring programs provided a stable communication.

• 대한기계학회논문집A
• /
• 제29권5호
• /
• pp.726-733
• /
• 2005

A spherical surface referenced Shack-Hartmann method is studied for inspecting machining accuracy of large concave mirror This method is so strong to the vibration environment for using as an on-machine inspection system during polishing process of large optics comparing with the interferometry. The measuring uncertainty of the system is shown as less than p-v 150 m. On-machine measured surface profile data with this method is used for feed back control of the polishing time or depth to improve the surface profile accuracy of large concave mirror. Also, the spherical surface referenced Shack-Hartmann method is useful for measuring aspheric such as parabolic or hyperbolic surface profile, comparing that the interferomehy needs a special null lens, which is to be a reference and difficult to fabricate.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1579-1582
• /
• 2005

Polishing is cutting process that polished workpiece by relative motion of abrasive grain between polishing tool and workpiece. According to relative motion forms(polishing patterns) of abrasive grain, the surface quality is different. Then, polishing patterns are important essential in polishing process. In work field, polishing patterns are determined by an expert of experience. Therefore, to work effective polishing, it is necessary that evaluate polishing characteristics for polishing patterns. And, polishing machine is made with cartesian coordinate robots, we estimate polishing characteristics by measurement of surface roughness.