• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제51권11호
• /
• pp.612-615
• /
• 2002

The main advantages of Disk type Single-Phase Switched Reluctance Motor (DSPSRM) is the simple construction, rugged structure, low manufacturing cost and simple driving circuit. It is especially possible to make the short axial length of DSPSRM. Therefore, it is suitable to setup this motor in a narrow space. This paper presents the shape design to maximize the average torque of DSPSRM that is achieved by 3D Finite Element Method (3D FEM) considering the nonlinear of magnetic material. The characteristics of two different rotor shapes are compared. The design parameters, such as the rotor and stator pole arc, are selected to the parametric study. The effect of pole arc ratios on the torque performance is investigated. From these results, the optimal pole arc to produce the maximum torque is determined.

• 한국철도학회논문집
• /
• 제15권3호
• /
• pp.237-243
• /
• 2012

3차원 유한요소법을 이용하여 엔드코일 효과를 고려한 SRM의 자계해석을 수행하였다. 고정자 극 형상에 따른 자계특성의 비교를 통하여 제안된 형상에서 자계특성이 향상됨을 확인하였다. 해석한 자계특성을 적용하여 철도부하에 대한 PI 제어기와 슬라이딩모드 제어기의 속도제어를 수행하였다. 속도 제어 시뮬레이션은 Matlab-Simulink를 사용하여 구현되었으며 부하 가변 조건에서 슬라이딩모드 제어기가 PI 제어기에 비해 더 우수한 과도응답 및 정상상태응답을 나타냄을 확인하였다.

• 조명전기설비학회논문지
• /
• 제22권3호
• /
• pp.88-95
• /
• 2008

In the paper, the permanent magnet synchronous generator of 1.5[MW] output power which is driven directly without gear system is designed by conventional magnetic equivalent circuit method and analyzed by finite element method. We analyzed the characteristics of generator like no load, rated load, short circuit condition and demagnetization of permanent magnet in order to verify the design results by magnetic circuit method. The last, the analysis results of two kinds of rotor types are compared with each other. Especially the THD(total harmonic distortion) of output voltage is examined for the comparison.

• 한국정밀공학회지
• /
• 제19권5호
• /
• pp.110-117
• /
• 2002

This paper proposes a optimization of the design variables of linear motor for the improvement of thrust. Especially, this paper treats the shoe, which can be good to flow of a magnetic flux in linear motor. Firstly, this paper uses a space harmonic analysis method(SHAM) based on Fourier series, for analyzing the characteristics of core type linear motor, including slot structure and shoe. And compare the magnetic flux densities of linear motor at air gap with the results of the SHAM and the Finite Element Method(FEM). Secondly, this paper uses a genetic algorithm, which is good to find the global solutions. The design variables are the pole pitch of magnet, the pitch of slot, the height of slot, the width of shoe and the width of magnet. The maximum thrust with optimum design variables is about 247 N which is improved about 16%.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 춘계전력전자학술대회 논문집(2)
• /
• pp.824-827
• /
• 2003

Recently, Development of Rare Earth Permanent magnet with the high remanence, high coercivity allow the design of brushless motors with very high efficiency over a wide speed range. Cogging torque is produced in a permanent magnet by magnetic attraction between the rotor mounted permanent magnet and the stator teeth. It is an undesired effect that contributes to the machines output ripple, vibration, and noise. This cogging torque can be reduced by variation of magnet arc length, airgap length, magnet thickness, shifting the magnetic pole and varying the radial shoe depth and etc. In this paper, Some airgap length and magnet arc that reduce cogging torque are found by FEM(Finite element method). The SPM type of high-capacity BLDC motor is optimized as a sample model.

• 전력전자학회논문지
• /
• 제9권2호
• /
• pp.112-118
• /
• 2004

본 논문은 선박 추진 장치를 위한 저속 영역에서 최대 토크를 내는 대용량 BLDCM(Brushless DC motor)의 설계에 관한 연구이다. 기존의 추진 장치용 모터는 직류기 및 권선형 유도 전동기 등을 사용함으로 인하여 유지 보수가 필요하였다. 본 논문에서는 유지 보수가 필요 없고 저속에서 큰 토크를 발생 할 수 있는 BLDCM 설계를 하였다. 설계시 출력 리플 및 진동, 소음을 유발하는 코깅 토크 저감을 고려하기 위해 설계변수로 공극길이와 자극 각 등을 취하여 이의 변화에 대한 최저 코깅 토크를 가지는 최적형상을 구하고, 전동기 특성을 FEM과 Maxwell stress tensor법을 이용하여 해석하였다. 최저의 코깅 토크를 가지며 저속영역에서 최대 토크를 발생 할 수 있는 선박 추진 장치용 SPM type의 BLDCM을 설계하였다.