• Journal of Environmental Science International
• /
• v.7 no.1
• /
• pp.36-40
• /
• 1998

This study was carried out to investigate the collection Efficiency of mass in collector step at the different of physical gas characterization. This work has focused on the dependence of the collection efficiency of mass in the collector zone of a two-stage set up field with gas temperature T and the dew point tmeperature. To identify the dependence of the mass collection efficiency on the Bounded plate of the collector zone MP.k by the spectre electric resistance of dust $p_e$. and the relative humidify ${\varphi}$, 20 at- tempts have been made with three different gas temperature ($50{\circ}C, 80{\circ}C, 110{\circ}C$) at different dew point. At the specific electric resistance of dust $p_e$=$10^6{\Omega}m$ which relative humidity corresponds to $\phi$ > 15%, a easy rise of the sounded plate secluded dust mass share was measured atwain. As the result of the higher cohesion imprisonment power due to the adsorbtion of particle, the rinse of the relative humidity developed on the particle surface. Therefore, the collection efficiency of mass was not predominant the high temperature T in the collector zone, neither was the pecific ellectric resistance of dust dependent.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.6
• /
• pp.782-786
• /
• 2010

Thrust deduction related to the prediction of power performance of a ship is rather resistance increase, and as a preliminary study for it forces upon a circular cylinder in a uniform flow of ideal fluid due to singularities located behind it are investigated. The circle theorem is used to get the complex velocity potential for the flow field under consideration, and the Blasius theorem is applied to obtain forces upon the circular cylinder. As singularities sinks, point vortices and dipoles and their combinations are treated. $\varepsilon$, standing for the strength of a singularity, and $\delta$, representing the distance between the cylinder and the singularity, are important small parameters for the resistance and lateral forces. For sinks or point vortices it is shown that the dimensionless forces upon the cylinder is O($\epsilon$) if $\epsilon$= O($\delta$) is assumed, and the same holds for dipoles if $\epsilon$= O(${\delta}^3$) is supposed. Forces upon the cylinder by a symmetric pair of sinks are greater than a single sink located at the central plane since there is an additional term due to cross effects, and the same is also valid for the case of dipole. Combination of dipole and a point vortex is also considered and a few new aspects are clarified.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.11
• /
• pp.23-28
• /
• 2020

In general, lithography techniques are applied when machining single-crystal silicon in nanoscale applications; however, these techniques involve low degrees of freedom for the vertical shapes. By applying mechanical techniques to machine silicon, nanopatterns having various types of vertical shapes can be manufactured. In this study, we determined the ductile-brittle machining transition point and analyzed the- variation of the specific cutting resistance within the ductile machining region in nanoscale applications. When brittle fracture occurred during the nanoscale cutting, the depth of cut and cutting force increased and decreased rapidly, respectively. The first point of rapid increase in the depth of cut was defined as the ductile-brittle machining point. Subsequently, the shape of the machining tool was observed using a scanning electron microscope to calibrate the machining area, considering the tip blunting. The specific cutting resistance decreased continuously and converged to a certain value during the nanoscale cutting. The decrease and convergence in the value can be attributed to the decrease in the ratio of the arc length to the area of the machining tool and silicon.

• Journal of Sensor Science and Technology
• /
• v.18 no.1
• /
• pp.86-94
• /
• 2009

Temperature measurement capability was inter-compared using the transfer standard platinum resistance thermometers(SPRT) among four laboratories of KRISS. The transfer SPRTs were primarily calibrated at the triple point of water and Ga melting point, then used at inter-comparison experiment. Temperature difference of calibration value between temperature laboratory and length laboratory at $20^{\circ}C$ was -0.7 mK and +2.4 mK at density laboratory. Temperature measured near $20^{\circ}C$, $25^{\circ}C$ and $30^{\circ}C$ at fluid flow laboratory was deviated by $34.2{\sim}80.4\;mK$ from the calibration values of the transfer SPRT. Ga melting points was inter-compared among three laboratories, and the difference of Ga melting points against the standard Ga melting point of temperature laboratory were $0.03{\sim}0.54\;mK$ at length laboratory and 0.02 mK at density laboratory.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.82-84
• /
• 2003

In case contact between point of contacts is not achieved well, contact resistance is grown, and by current concentration at current conducting contacts can weld. In order to decrease contact resistance between contacts in case of busbar, installing spring between fixed contact and moving contact. and then force on faying surface of contacts increase and contact resistance decrease. But, in case increase force of spring to widen contact area, operating force moving contact can grow, on the contrary force of spring is small, contact resistance becomes low. Therefore, need to optimize force and number of spring. position, and also need to examine force change on contact surface at point of contact moving. In this paper, dynamic kinetics analysis for force on faying surface of contacts is performed at unsteady state. It is showed to not uniform force on surface between contacts, and we can got more uniform force by means of change spring position.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.245-252
• /
• 2000

Model tests on free standing pile groups and piled footings with varying a pile spacing in two layered soils are carried out. The influence of pile cap on the behaviors of end bearing pile groups is analyzed by comparing the bearing behavior in piled footings with those in a single pile, a shallow footing(cap alone) and free standing pile groups. From the test results, it is found that the bearing characteristics of cap-soil-pile system are related with load levels and pile spacings. Before yield, the bearing resistance by cap is not fully mobilized, however, as the applied load increases, the bearing resistance of cap approaches to that of cap alone and settlement hardening occurs after yield due to the compaction caused by the contact pressure between cap and soil. By the cap-soil-pile interaction, shaft friction and point resistance of piles considerably increase with dependency of pile spacings. In two layered soil, the increasing effect of dilatancy in dense sandy soil adjacent to pile tips, increases the point resistance of pile.

• Journal of the Korean Society of Safety
• /
• v.14 no.1
• /
• pp.66-72
• /
• 1999

Local heating transportation pipe has sensor and return lines to detect water-leakage. There are impulse and resistance comparison measurement types for a water-leakage detection. The impulse type shows large detection error within a measurement range. Since the resistance comparison type can find a comparative accurate single water-leakage point in the measurement range of heating pipe, it has been used to detect water-leakages these days. However if the multi water-leakages are happened in the measurement range of transportation pipe. the resistance comparison type shows a detection error point by the parallel resistance between a detection sensor line and ground. But the detection error will be minimized by the divided transportation pipe loops. In this research, it suggests the design of remote controlled detection system which can divide a large pipe loop and a possible single water-leakage measurement process in each divided loops.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.146-147
• /
• 2007

A universal four-point contact measurement method, has an advantage of non-existence of contact resistance, is demonstrated by the experiments with carbon nanotubes and ZnO nanowire. Ti/Au and Pt are tried to compare the influence of contact resistance between two different metals. These metals are selected to make Ohmic contact and Schottky contact originated from their different work functions. For precise experiments, Ti/Au and Pt are separately evaporated to form double 'four-point contact electrodes' on CNTs or ZnO, and the voltage-current characteristics are measured. This method can be applied to universal resistivity measurement for nanotubes and nanowires.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2012.10a
• /
• pp.160-161
• /
• 2012

The traditional theory regarding the pivot point of a ship during maneuvering, so called apparent pivot point, is located nearly at 1/3 ship's length from the bow when the ship is moving ahead, and between 1/4 ship's length from the stern and the rudder post when going astern. The pivot point is sometimes considered to be the centre of leverage for forces acting on the ship. However, the pivot point is located out of ship due to strong lateral force, such as current and it is very inconvenient to use during maneuvering a ship. In this paper firstly, pivot points due to ship's condition are investigated carefully. And then the center of lateral resistance used at the present are determined. While a new lateral force is added, we can compare the pivot point with the center of lateral forces. Finally, we will suggest the center of all lateral forces for maneuvering instead of pivot point. Especially, it will be very helpful for pilots to handle ships in simulation.

• Journal of Welding and Joining
• /
• v.29 no.5
• /
• pp.99-105
• /
• 2011

In this study, effect of Si content on nugget diameter in electric resistance spot welded dual-phase(DP) steel was investigated. The cold rolled DP steels with different Si content (0.5, 1.0, 1.5, 2.0 wt.%) were used and thickness of those sheet was 1.2mm. With increasing Si content, nugget diameter was increased at the same welding current. This is attributed to increase of heat input result from high resistivity. Also, nugget diameter was increased with an increase in Si content for the same heat input. For this reason, the melting point of DP steel is lowered with an increase in the Si content. And solid DP steel can easily be transformed to a liquid phase because the low melting point. Finally, a prediction formula for the nugget diameter(N.D.) could be obtained in terms of heat input(Q) and melting point(M.P) as follows: N.D.(mm) = 0.11Q(J) - 0.0031 M.P.($^{\circ}C$) + 0.32.