• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.1882-1887
• /
• 2007

In the present experimental study, the effect of interfacial tensions on pressure drop of air-water two-phase flow in round mini-channels was investigated. A glass (highly wettable) tube and a Teflon (poorly wettable) tube, both in 350 mm length but 1.8 mm and 1.59 mm in inner diameters each, were used for the tests. All the experiments were performed only in the plug flow regime, confirmed by visualization. In the glass tube, the gas plugs were surrounded by the liquid film along the inner periphery. On the other hand, the inner wall remained dry at the gas portion in the Teflon tube. The pressure drop of the plug flow in the Teflon tube without the liquid film) appeared much larger than in the glass tube (with the liquid film) due to dissipation of energy by movement of the wetting lines. In this paper, various correlations on the two-phase pressure drop of plug flows were compared and a modified correlation was proposed, taking account of the surface wettability.

• Journal of the Korean Society for Precision Engineering
• /
• v.5 no.4
• /
• pp.24-31
• /
• 1988

The Upper Bound Solution has been used to investigate the effect of the various parameters on the floating-plug tube-drawing precess. A kinematically admissible velocity field considering the change of the tube thickness is proposed for the deformation process. Taking into account the position of the plug in the deforming region, shear energy at entrance and exit, friction energy on contact area, homogeneous energy are calculated. The theoretical values in proposed velocity field are good agreement with experimental values, It is investigated that the tube thickness in the deforming region is changed slightly toward minimization of deforming energy and then the drawing stress in lower than the crawing stress in the velocity field that the tube thickness is uniform.

• Korea Science and Art Forum
• /
• v.19
• /
• pp.561-568
• /
• 2015

A lot of electrical energy is used in our daily life. While energy saving concerns are overall, consumption practices of people in general are very different. People want to control their energy use and by knowing the amount of energy they use. Smart plug is a new device that measures electricity usage through each plug at an outlet with on/off control. User experience for electrical devices in regards to electricity usage should be newly designed. In this study, based on the survey, personas have been devised and their energy use experience in relation with smart plugs have been designed. Service models have been designed as well. By designing service with smart plug, user could enhance the experience of energy usage and saving and energy consumption practices could be improved in a sustainable manner.

• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2000.09a
• /
• pp.93-103
• /
• 2000

The concrete plug in an underground cavern prevents the stored product (oil, gas, etc) from leaking and the excessive show of underground water, so it plays an important role in construction and operation of the storage cavern. Additionally, it should maintain its stability under every possible loading condition. Once the plug is constructed, the cavern is isolated from the external access. Therefore, mechanical and hydraulic consideration should be made in construction to fulfill its function. Therefore, in this study, numerical analyses were conducted to study the optimal shape and thickness of the plug with respect to the various conditions of installation depth, the shape of the plug, in-situ stress ratio (K), the condition of rock-plug interface, and the effect of Excavation Damaged Zone (EDZ). This paper also presents the effect of slot depth on the hydraulic behavior of the plug. These analyses were carried out by using the 2-dimensional finite difference code, rm FLAC, and the 3D code, m FLA $C^{3D}$./.

• Tunnel and Underground Space
• /
• v.10 no.3
• /
• pp.344-354
• /
• 2000

The concrete plug in an underground cavern prevents the stored product (oil, gas, etc) from leaking and the excessive inflow of underground water, so it plays an important role in construction and operation of the storage cavern. Additionally, it should maintain its stability under every possible loading condition. Once the plug is constructed, the cavern is isolated from the external access. Therefore, mechanical and hydraulic consideration should be made in construction to fulfill its function. Therefore, in this study, numerical analyses were conducted to study the optimal shape and thickness of the plug with respect to the various conditions of installation depth, the shape of the plug, in-situ stress ratio (K), the condition of rock-plug interface, and the effect of Excavation Damaged Zone (EDZ). This paper also presents the effect of slot depth on the hydraulic behavior of the plug. These analyses were carried out by using the 2-dimensional finite difference code, rm FLAC, and the 3D code, rm FLAC$\^$3D/.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.3
• /
• pp.46-57
• /
• 1995

The aim of the present study is to provide fundamental informations for the development of magneticfluid actuator. To achieve the aim, oscillation characteristics of the magneticfluid plug are investigated by experiment for the various length and position of the magneticfluid plug and the frequency of magnetic field. The oscillation characteristics are obtained. Amplitude, natural frequency, phase shift and damping ratio, are compared with theoretical values. From the study, the following conclusive remarks can be made. The experimental equation for the magnetic field is obtained. The critical magneticfluid length exists and its value is about 70mm. The range of the damping ratio and fluid loss coefficient obtained by experiment are 0.1~0.2 and 30~100, respectively. Comparison between experimental and theoretical results of oscillation characteristics shows good agreement in the high frequency range. Meanwhile, in the low frequency range, there appears little discrepancies(5% in the frequency and amplitude and 10% in phase difference and damping ratio) with each other.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.10 no.1
• /
• pp.70-77
• /
• 2007

Simulation Based Acquisition(SBA) gains interest from the defense acquisition community. To accomplish SBA efficiently, M&S should be collaborately used in. This paper proposes PBA(PlugIn-Based Architecture) that is a common software development infrastructure and provides reuse mechanism with plugin components. PlugIns are reuse entity possible to plug-in-play statically and dynamically. This architecture supports stand alone simulation and HLA-compliant distributed simulation also.

• Journal of People, Plants, and Environment
• /
• v.24 no.5
• /
• pp.499-507
• /
• 2021

Background and objective: This study was carried out to develop an effective technique for raising seedlings of Veronica pyrethrina Nakai, a native plant species in the Korean Peninsula, in plug trays. Methods: To investigate the optimum plug cell size and sowing media, we sowed seed in to plug trays with 34, 21, and 10 mL cells and filled with a commercial horticultural substrate and mixtures of peatmoss and perlite in 1:1, 3:1, and 4:1 ratios. Fertilization levels were set at 0, 500, 1000 and 2000 mg·L^-1. Results: Plug cell size did not significantly influence the seedling growth of V. pyrethrina. By substrate type, the growth rate was highest in the horticultural substrate, followed by 4:1, 3:1, and 1:1. Growth by fertilization level was higher in all fertilized treatment groups than in the control group, and there was no difference among 500, 1000, and 2000 mg·L^-1. Conclusion: The results of this study proved that it is most suitable for raising seedlings of V. pyrethrina to sow the seeds in a 10 mL cell plug tray filled with horticultural substrates, and apply fertilizers with less than 500 mg·L^-1 concentration.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.644-648
• /
• 2004

In the present study were examined numerically and experimentally the off-design performance characteristics on an axisymmetric plug nozzle with variable throat area. In this nozzle concept, its throat area can be changed by translating the plug into the axial direction. First, a mixed-expansion plug nozzle, in which two expansion parts are arranged both inside and outside, was designed by means of the method of characteristics. Second, the CFD analysis was verified by the cold-flow wind tunnel test. Third, its performance characteristics were evaluated over a wide range of pressure ratio from half to double throat area through the design point, using the CFD code verified by the wind tunnel tests. It was made clear from the study that not so critical thrust efficiency losses were found and the maximum thrust efficiency loss was at most approximately 5 % under off-design conditions without external flow. This result shows that a plug nozzle can give the altitude compensation even under off-design geometry operations. However, shock waves were observed in the inner expansion part under the doubled throat area operation and thus some thermal problems may be caused on the plug surface. Furthermore, collapse of cell structure on the plug surface was observed with external flow (around Mach number 2.0) as it became lower pressure ratio below the design point and the fact may result in big efficiency loss regardless of geometrical configuration.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.7 no.3
• /
• pp.151-156
• /
• 2012

When mounting the sensor device in the way of Plug&Play, sensor device drivers need to be loaded and linked dynamically. Since a sensor node platform is based on small 8 bit MCU, dynamic loading and linking technique used in Windows and Linux can not be applied. In this paper, we present how to link and load dynamically sensor device drivers for sensor device Plug&Play. We implement a prototype and evaluate it to make sure that there is no performance degradation like sensor device driver connection speed and memory usage. Connection speed overhead increases to 0.2ms. Memory usage overhead increases to hundreds byte. It shows that there is no heavy influence in running the actual program.