• 한국지반공학회지:지반
• /
• 제13권4호
• /
• pp.163-176
• /
• 1997

NATM 터널에서 강지보재로 이용되어지는 H형강은 그 동안 많은 단점이 지적되어 왔으며, 그 중 하나는 숏크리트 타설시 H형강 flange 배면에 발생하는 공동으로 인하여 숏크리트를 포함 한 초기지보재의 하중지지력 저감을 들 수 있다. 이와 같은 단점을 보완하기 위하여 유럽의 많은 나라에서는 H형강 지보재와 같은 plate girder 형태의 지보재에 비하여 많은 장점을 가진 fat twice girder(격자지보)라는 지보재를 개발하여 현장에 적용하고 있다. 터널 굴착시 격자지보를 초기 지보재로서 효율적으로 사용하기 위해서는 하중지지력에 대한 심도있는 연구가 필요하다. 따라서 본 연구에서는 격자지보의 하중지지력 평가 및 검증의 일환으로 격자지보에 대한 굴곡시험과 압축시험을 수행하였다. 그 결과 격자지보는 H형강 지보재에 비하여 우수한 하중지지력을 보유하는 것으로 나타났으며, 따라서 터널 시공시 지보재로서 효율적으로 적용할 수 있을 것으로 판단된다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제5권3호
• /
• pp.348-363
• /
• 2013

The use of I-Core sandwich panel has increased in cruise ship deck structure since it can provide similar bending strength with conventional stiffened plate while keeping lighter weight and lower web height. However, due to its thin plate thickness, i.e. about 4~6 mm at most, it is assembled by high power $CO_2$ laser welding to minimize the welding deformation. This research proposes a volumetric heat source model for T-joint of the I-Core sandwich panel and a method to use shell element model for a thermal elasto-plastic analysis to predict welding deformation. This paper, Part I, focuses on the heat source model. A circular cone type heat source model is newly suggested in heat transfer analysis to realize similar melting zone with that observed in experiment. An additional suggestion is made to consider negative defocus, which is commonly applied in T-joint laser welding since it can provide deeper penetration than zero defocus. The proposed heat source is also verified through 3D thermal elasto-plastic analysis to compare welding deformation with experimental results. A parametric study for different welding speeds, defocus values, and welding powers is performed to investigate the effect on the melting zone and welding deformation. In Part II, focuses on the proposed method to employ shell element model to predict welding deformation in thermal elasto-plastic analysis instead of solid element model.

• 전산구조공학
• /
• 제4권4호
• /
• pp.125-133
• /
• 1991

구조응답이나 상태함수가 음함수(implicit function)형태로 주어지는 복잡한 구조물의 설계감도해석 및 신뢰성해석을 효율적으로 수행할 수 있는 방법을 개발하기 위하여, 먼저 확률 유한요소법을 사용한 확정론적 감도해석 방법을 정식화하고, 이를 바탕으로 MVFOSM, AFOSM 및 SORM등의 2차 모우먼트 방법에 의한 신뢰성 해석을 수행하였으며, 또한 신뢰성에 기초한 최적설계를 수행하는 경우에 필요한 확률론적 설계감도해석 방법을 제시하였다. 수치해석 예로서 박판 구조물의 평면응력문제와 판굽힘문제에 대한 해석을 수행하였는데, 초기 항복이 발생하는 경우를 파괴상태로 정의하였으며, 외부하중, 항복응력, 판두께, 탄성계수 및 Poisson비 등을 확률변수로 다루었다. 모든 경우에 있어서, 본 논문에서 제시한 방법으로 구한 구조응답의 분산이나 파괴확률이 Monte Carlo simulation의 결과와 잘 일치함을 알 수 있었으며, 또한 신뢰성설계시, 확률론적 감도해석결과로부터 확률변수들의 상대적 중요도를 파악할 수 있을 뿐만 아니라, 설계변수(혹은 확률변수)의 평균 혹은 분산계수의 변화에 따른 신뢰성지수의 변화량을 미리 예측할 수도 있다.

• 한국공간구조학회논문집
• /
• 제18권3호
• /
• pp.57-66
• /
• 2018

Recently various composite beams in which concrete is filled in the U-shaped steel plate have been developed for saving story height and reducing construction period. Due to the high flexural stiffness and strength, they are widely being used for the building with large loads and long spans. The semi-slim AU composite beam has proven to take highly improved stability compared to the existing composite beams, because it consists of the closed steel section by attaching cap-type shear connectors to the upper side of U-shaped steel plate. In this study the finite element analyses were performed to evaluate the safety of the AU composite beam with unconsolidated concrete which were sustained through the closed steel section during the construction phase. The analyses were performed on the two types of cross section applied to the fabrication of AU composite beams, and the results were compared to the those of 2-point bending tests. In addition, the flexural performance according to the space of intermittent cap-type shear connectors and the location of reinforcing steel bars for compression was comparatively investigated. Through the results of analytical studies, it is preferable to adopt the yield moment of AU composite beam for evaluating the safety in the construction phase, and to limit the space of intermittent shear connectors to 400 mm or less for the construction load.

• Journal of Welding and Joining
• /
• 제27권6호
• /
• pp.31-35
• /
• 2009

When conducting CTOD test, especially in thick welded steel plate, fatigue pre-cracking occasionally failed to satisfy the requirements of standards thus making the test result invalid. Internally accumulated residual stress of test piece has been thought as one of the main reasons. The propagation of fatigue crack, started from the tip of machined notch, which might have propagated irregularly due to residual stress field. To overcome this kind of difficulty three methods to modify the residual stress are suggested in standard i.e. local compression, reverse bending and stepwise high-R ratio method. In this paper not only multi pass welding but also local pre-compressing process of thick steel plate has been simulated using finite element method for clarifying variation of internal welding residual stress. The simulated results show that welding residual stress is compressive in the middle section of the model and it is predominantly increased after machining the specimen. Comparing as-welded state all component of the welding residual stress changing to compressive in the tip of machine notch whereas residual stress of the outer area remain as tensile condition relatively. Analysis results also show that this irregular residual stress distribution is improved to be more uniformly by applying local compression.

• Composites Research
• /
• 제32권4호
• /
• pp.185-190
• /
• 2019

본 연구에서는 단순지지 경계조건을 갖는 적층 복합재료 사다리꼴 주름판에 대한 탄성 좌굴특성을 이론적 방법을 이용하여 분석하였다. 좌굴 해석에서는 한 방향 하중, 두 방향 하중 및 전단하중 등 3가지 유형의 내평면 하중조건이 고려되었다. 3차원 주름 구조물을 해석적으로 기계적 거동을 표현하는 것이 매우 어렵기 때문에 본 해석에서는 주름판의 전반적인 좌굴 거동을 분석하기 위해 등가균질모델을 적용하였다. 이를 위해 단위 주름을 직교이방성재료로 등가시켰으며, 이전 연구에서 유도한 주름판에 대한 등가 굽힘강성계수식을 본 해석에 적용하였다. 제안된 이론해석 결과의 타당성을 검증하기 위해 셸요소를 바탕으로 한 3차원 유한요소해석을 수행하였으며, 두 방법을 이용해 얻은 임계 좌굴하중 및 좌굴형상을 비교하였다. 주름판의 기하형상에 따른 영향을 분석하기 위해 다양한 수치 예가 제시되었다.

• Steel and Composite Structures
• /
• 제29권6호
• /
• pp.717-734
• /
• 2018

This paper presents the flexural performance of steel beam-to-column joints composed of hollow structural section beams and columns. A finite element (FE) model was developed incorporating geometrical and material nonlinearities to evaluate the behaviour of joints subjected to bending moments. The numerical outcomes were validated with experimental results and compared with EN1993-1-8. The demountability of the structure was discussed based on the tested specimen. A parametric analysis was carried out to investigate the effects of steel yield strength, end-plate thickness, beam thickness, column wall thickness, bolt diameter, number of bolts and location. Consequently, an analytical model was derived based on the component method to predict the moment-rotation relationships for the sub-assemblies with extended end-plates. The accuracy of the proposed model was calibrated by the experimental and numerical results. It is found that the FE model is fairly reliable to predict the initial stiffness and moment capacity of the joints, while EN1993-1-8 overestimates the initial stiffness extensively. The beam-to-column joints are shown to be demountable and reusable with a moment up to 53% of the ultimate moment capacity. The end-plate thickness and column wall thickness have a significant influence on the joint behaviour, and the layout of double bolt-rows in tension is recommended for joints with extended end-plates. The derived analytical model is capable of predicting the moment-rotation relationship of the structure.

• Steel and Composite Structures
• /
• 제38권2호
• /
• pp.151-164
• /
• 2021

During the pipe forming process, a steel plate undergoes inelastic behavior multiple times under a load condition repeating tension and compression in the circumferential direction. It derives local reduction or increase of yield strength within the thickness of steel pipes by the plastic hardening and Bauschinger effect. In this study, a combined hardening model is proposed to effectively predict variations of yield strength in the circumferential direction of API-X65 and X70 steel pipes with relatively low t/D ratio during the forming process, which is expected to experience accumulated plastic strain of 2~3%, the typical Lüder band range in a low-carbon steel. Cyclic tensile tests of API-X65 and X70 steels were performed, and the parameters of the proposed model for the steels were calibrated using the test results. Bending-flattening tests to simulate repeated tension and compression during pipe forming were followed for API-X65 and X70 steels, and the results were compared with those by the proposed model and Zou et al. (2016), in order to verify the process of material model calibration based on tension-compression cyclic test, and the accuracy of the proposed model. Finally, parametric analysis for the yield strength of the steel plate in the circumferential direction of UOE pipe was conducted to investigate the effects of t/D and expansion ratios after O-forming on the yield strength. The results confirmed that the model by Zou et al. (2016) underestimated the yield strength of steel pipe with relatively low t/D ratio, and the parametric analysis showed that the t/D and expansion ratio have a significant impact on the strength of steel pipe.

• 한국구조물진단유지관리공학회 논문집
• /
• 제27권1호
• /
• pp.19-29
• /
• 2023

실리카 흄과 같은 고가의 혼화재 투입 없이 원심성형 공정 활용으로 콘크리트의 수밀성 증대 통한 콘크리트 압축강도 100 MPa급 초고강도 프리스트레스 각형보를 개발하였다. 벽체에 가설된 초고강도 원심성형 각형보는 상부슬래브 콘크리트와 합성된 후에 공용하중을 받게 되는데, 원심성형 보와 바닥판 사이에는 휨에 의해 수평전단응력이 발생되고 이는 스터드나 철근 등의 전단연결재를 통해서 보와 바닥판이 합성거동을 하게 된다. 본 연구에서는 공장에서 생산된 100 MPa급 원심성형 각형보 상부에 RC슬래브를 제작하여 합성시킨 실물모형 시험체에 대한 휨재하시험을 수행하였으며, 합성단면은 설계 공칭휨강도를 넘어 안정적인 합성거동을 하면서 파괴되어 구조적인 신뢰성을 입증하였다.

• Geomechanics and Engineering
• /
• 제31권5호
• /
• pp.505-518
• /
• 2022

This study introduces soil resistance multipliers at locations encompassed by the zone of influence of the helix plate to consider the added lateral resistance provided to the helical pile. The zone of influence of a helix plate is a function of its diameter and serves as a boundary condition for the modified soil resistance springs. The concept is based on implementing p-multipliers as a reduction factor for piles in group action. The application of modified p-y springs in the analysis of helical piles allows for better characterization and understanding of the lateral behavior of helical piles, which will help further the development of design methods. To execute the proposed method, a finite difference program, HPCap (Helical Pile Capacity), was developed by the authors using Matlab. The program computes the deflection, shear force, bending moment, and soil resistance of the helical pile and allows the user to freely input the value of the zone of influence and Ω (a coefficient that affects the value of the p-multiplier). Results from ten full-scale lateral load tests on helical piles embedded at depths of 3.0 m with varying shaft diameters, shaft thicknesses, and helix configurations were analyzed to determine the zone of influence and the magnitude of the p-multipliers. The analysis determined that the value of the p-multipliers is influenced by the ratio between the pile embedment length and the shaft diameter (D_p), the effective helix diameter (D_h-D_p), and the zone of influence. Furthermore, the zone of influence is recommended to be 1.75 times the helix diameter (D_h). Using the numerical analysis method presented in this study, the predicted deflections of the various helical pile cases showed good agreement with the observed field test results.