• 국제강구조저널
• /
• 제18권5호
• /
• pp.1617-1630
• /
• 2018

The crucial differences between conventional rail with split-type connectors and continuous welded rails are axial stress in the longitudinal direction and stability, as well as other issues generated under the influence of loading effects. Longitudinal stresses generated in continuously welded rails on railway bridges are strongly influenced by the nonlinear behavior of the supporting system comprising sleepers and ballasts. Thus, the track structure interaction cannot be neglected. The rail-support system mentioned above has properties of non-uniform material distribution and uncertainty of construction quality. The linear elastic hypothesis therefore cannot correctly evaluate the stress distribution within the rails. The aim of this study is to apply the nonlinear finite element method using the nonlinear coupling interface between the track and structural model and to illustrate the welded rail behavior under the loading effect and uncertain factors of the ballast. Numerical results of nonlinear finite analysis with a three-dimensional solid and frame element model are presented for a typical track-bridge system. A composite plate girder, modeled by solid and shell elements, is also analyzed to consider the behavior of the welded rail. The analysis result showed buckling under the independent calculations of load cases, including 'temperature change', 'bending of the supporting structure', and 'braking' of the railway vehicle. A parametric study of the load combination method and the loading sequence is also included in this analysis.

• 대한금속재료학회지
• /
• 제46권5호
• /
• pp.321-327
• /
• 2008

Cu based amorphous ($Cu_{54}Zr_{22}Ti_{18}Ni_6$) coating was produced by cold spraying as a new fabrication process. The microstructure and macroscopic properties of amorphous coating layer was investigated and compared with those of cold sprayed pure Cu coating. Amorphous powders were prepared by gas atomization and Al 6061 was used as the substrate plate. X-ray diffraction results showed that Cu based amorphous powder could be successfully deposited by cold spraying without any crystallization. The Cu based amorphous coating layer ($300{\sim}400{\mu}m$ thickness) contained 4.87% porosity. The hardness of Cu based amorphous coating represented $412.8H_v$, which was correspond to 68% of the hardness of injection casted bulk amorphous material. The wear resistance of Cu based amorphous coating was found to be three times higher than that of pure Cu coating. The 3-point bending test results showed that the adhesion strength of Cu based amorphous coating layer was higher than that pure Cu coating. It was also observed that hard Cu base amorphous particle could easily deform soft substrate by particle collisions and thus generated strong adhesion between coating and substrate. However, the amorphous coating layer unexpectedly represented lower corrosion resistance than pure Cu coating, which might be resulted from the higher content of porosity in the cold sprayed amorphous coating.

• Structural Engineering and Mechanics
• /
• 제83권5호
• /
• pp.693-707
• /
• 2022

Bonded joints have proven their performance against conventional joining processes such as welding, riveting and bolting. The single-lap joint is the most widely used to characterize adhesive joints in tensile-shear loadings. However, the high stress concentrations in the adhesive joint due to the non-linearity of the applied loads generate a bending moment in the joint, resulting in high stresses at the adhesive edges. Geometric optimization of the bonded joint to reduce this high stress concentration prompted various researchers to perform geometric modifications of the adhesive and adherends at their free edges. Modifying both edges of the adhesive (spew) and the adherends (bevel) has proven to be an effective solution to reduce stresses at both edges and improve stress transfer at the inner part of the adhesive layer. The majority of research aimed at improving the geometry of the plate and adhesive edges has not considered the effect of temperature and water absorption in evaluating the strength of the joint. The objective of this work is to analyze, by the finite element method, the stress distribution in an adhesive joint between two 2024-T3 aluminum plates. The effects of the adhesive fillet and adherend bevel on the bonded joint stresses were taken into account. On the other hand, degradation of the mechanical properties of the adhesive following its exposure to moisture and temperature was found. The results clearly showed that the modification of the edges of the adhesive and of the bonding agent have an important role in the durability of the bond. Although the modification of the adhesive and bonding edges significantly improves the joint strength, the simultaneous exposure of the joint to temperature and moisture generates high stress concentrations in the adhesive joint that, in most cases, can easily reach the failure point of the material even at low applied stresses.

• 대한토목학회논문집
• /
• 제26권3A호
• /
• pp.457-464
• /
• 2006

화이버로 보강된 복합재료는 비강성과 강도가 높을 뿐만 아니라 경량화를 위한 작업이 가능한 재료로써, 항공, 선박 그리고 토목분야와 같은 많은 산업분야에서 계속적으로 사용이 증대되고 있다. 본 연구는 전단변형을 고려한 타원단면을 갖는 복합적 층 구조물의 좌굴하중 및 모드형상을 분석하였다. 좌굴해석을 수행하기 위해, 면내회전자유도를 갖는 평면응력 요소와 휨 요소를 결합하여 무결점 4절점 쉘요소를 작성하였다. 이때 추가변형률과 대체전단변형률을 도입함으로써 요소의 거동을 개선하였다. 해석모델에 대해 쉘의 기하학적 형상, 종횡비, 화이버 보강각도, 그리고 적층배열에 따른 영향을 고찰하였다. 본 연구에서 제시한 타원단면을 갖는 적층관의 임계좌굴하중과 모드형상은 여러 가지 설계변수에 의한 거동에 대한 정확한 이해로부터 효율적인 설계방향을 제시하고자 하였으며, 추후 적층관의 좌굴해석시 좋은 참고자료로 활용할 수 있으리라 기대된다.

• Computers and Concrete
• /
• 제33권1호
• /
• pp.27-39
• /
• 2024

In this study, the authors investigate the free vibration behavior of three-phases functionally graded sandwich plates using a novel nth-order shear deformation theory. These plates are composed of a homogeneous core and two face-sheet layers made of different functionally graded materials. This is the novel type of the sandwich structures that can be applied in many fields of mechanical engineering and industrial. The proposed theory only requires four unknown displacement functions, and the transverse displacement does not need to be separated into bending and shear parts, simplifying the theory. One noteworthy feature of the proposed theory is its ability to capture the parabolic distribution of transverse shear strains and stresses throughout the plate's thickness while ensuring zero values on the two free surfaces. By eliminating the need for shear correction factors, the theory further enhances computational efficiency. Equations of motion are established using Hamilton's principle and solved via Navier's solution. The accuracy and efficiency of the proposed theory are verified by comparing results with available solutions. The authors then use the proposed theory to investigate the free vibration characteristics of three-phases functionally graded sandwich plates, considering the effects of parameters such as aspect ratio, side-to-thickness ratio, skin-core-skin thicknesses, and power-law indexes. Through careful analysis of the free vibration behavior of three-phases functionally graded sandwich plates, the work highlighted the significant roles played by individual material ingredients in influencing their frequencies.

• Journal of Veterinary Science
• /
• 제25권1호
• /
• pp.2.1-2.14
• /
• 2024

Background: Sufficient surgical resection is necessary for effective tumor control, but is usually limited for vertebral tumors, especially in the cervical spine in small animal neurosurgery. Objective: To evaluate the primary stability and safety of customized three-dimensional (3D)-printed implants for cervical spine reconstruction after total vertebrectomy. Methods: Customized guides and implants were designed based on computed tomography (CT) imaging of five beagle cadavers and were 3D-printed. They were used to reconstruct C5 after total vertebrectomy. Postoperative CT images were obtained to evaluate the safety and accuracy of screw positioning. After harvesting 10 vertebral specimens (C3-C7) from intact (group A) and implanted spines (group B), implant stability was analyzed using a 4-point bending test comparing with groups A and C (reconstituted with plate and pins/polymethylmethacrylate after testing in Group A). Results: All customized implants were applied without gross neurovascular damage. In addition, 90% of the screws were in a safe area, with 7.5% in grade 1 (< 1.3 mm) and 2.5% in grade 2 (> 1.3 mm). The mean entry point and angular deviations were 0.81 ± 0.43 mm and 6.50 ± 5.11°, respectively. Groups B and C significantly decreased the range of motion (ROM) in C3-C7 compared with intact spines (p = 0.033, and 0.018). Both groups reduced overall ROM and neutral zone in C4-C6, but only group B showed significance (p = 0.005, and 0.027). Conclusion: Customized 3D-printed implants could safely and accurately replace a cervical vertebra in dog cadavers while providing primary stability.

• Steel and Composite Structures
• /
• 제51권4호
• /
• pp.441-456
• /
• 2024

This paper aims to develop Machine Learning (ML) algorithms to predict the buckling resistance of cold-formed steel (CFS) channels with restrained flanges, widely used in typical CFS sheathed wall panels, and provide practical design tools for engineers. The effects of cross-sectional restraints were first evaluated on the elastic buckling behaviour of CFS channels subjected to pure axial compressive load or bending moment. Feedforward multi-layer Artificial Neural Networks (ANNs) were then trained on different datasets comprising CFS channels with various dimensions and properties, plate thicknesses, and restraining conditions on one or two flanges, while the elastic distortional buckling resistance of the elements were determined according to the Finite Strip Method (FSM). To develop less biased networks and ensure that every observation from the original dataset has the chance of appearing in the training and test set, a K-fold cross-validation technique was implemented. In addition, the hyperparameters of the ANNs were tuned using a grid search technique to provide ANNs with optimum performances. The results demonstrated that the trained ANNs were able to predict the elastic distortional buckling resistance of CFS flange-restrained elements with an average accuracy of 99% in terms of coefficient of determination. The developed models were then used to propose a simple ANN-based design formula for the prediction of the elastic distortional buckling stress of CFS flange-restrained elements. Finally, the proposed formula was further evaluated on a separate set of unseen data to ensure its accuracy for practical applications.

• Steel and Composite Structures
• /
• 제52권4호
• /
• pp.405-418
• /
• 2024

To study the influence of different reduced beam section (RBS) on the mechanical performance of modular boltedwelded hybrid connection joints (MHCJs), this article uses ABAQUS to establish and verify the finite element model (FEM) of the test specimens on the basis of quasi-static test research. Based on, 14 joint models featuring different RBS are devised to evaluate their influence on seismic behavior, such as joint failure mode, bending moment (M)-rotation angle (θ) curve, ductility, and energy consumption. The results indicate that when the flange and web are individually weakened, they alleviate to some extent the concentrated stress of the core module (CM) and column end steel skeleton in the joint core area, but both increase the stress on the flange connecting plate (FCP). At the same time, the impact of both on seismic performance such as bearing capacity, stiffness, and energy consumption is relatively small. When simultaneously weakening the flange and web of the steel beam, forming plastic hinges at the weakened position of the beam end, significantly alleviated the stress concentration of the CM and the damage at the FCP, improving the overall deformation and energy consumption capacity of joints. But as the weakening size of the web increases, the overall bearing capacity of the joint shows a decreasing trend.

• 한국구조물진단유지관리공학회 논문집
• /
• 제26권1호
• /
• pp.73-80
• /
• 2022

본 연구에서는 공장에서 L형강을 이용하여 선조립한 NRC 보와 NRC 기둥을 현장에서 볼트 조립하는 NRC 보-기둥접합부 상세를 개발하였다. 개발된 접합부 상세는 NRC-J형과 NRC-JD형이다. NRC-J형은 NRC 기둥 측면의 강재 플레이트와 NRC 보의 엔드플레이트의 측면과 하부면에 TS볼트로 인장접합하는 방식이다. NRC-JD형은 전단에 대해서 NRC 보와 NRC 기둥의 측면을 고력볼트접합하고, 휨에 대해서 접합부를 관통하는 철근연결재와 보의 보강재를 겹침이음하도록하는 강접합 방식이다. 접합부 내진성능평가를 위하여, 두 가지 NRC 보-기둥 접합부 상세를 가지는 NRC-J 실험체, NRC-JD 실험체와 RC 보-기둥 접합부 상세를 가지는 RC-J 실험체 등 3개의 실험체를 제작하였다. 반복횡하중가력 실험결과, 모든 실험체의 최종 파괴형상은 보-기둥 접합면에서 보의 휨파괴로 나타났다. 정가력에 의한 실험체 최대내력은 RC-J 실험체에 비하여 NRC-J 실험체와 NRC-JD 실험체가 각각 10.1%, 29.6% 크게 나타났다. 두가지 NRC 접합부 상세 모두 KDS 기준(KDS 41 3100)의 합성중간모멘트골조 모멘트접합부에서 요구되는 최소 총층간변위각 0.03 rad 이상의 연성능력을 확보는 것으로 평가되었다. 부재각 5.7%에서 NRC-J실험체, NRC-JD 실험체가 RC실험체에 비해 약 34.8%, 61.1% 큰 누적 에너지 소산능력을 보유하고 있었다. NRC 보-기둥 접합부의 실험내력이 KDS 기준식에 의한 이론내력에 비하여 30%~53% 큰 것으로 평가되어, 기준식이 보유성능을 안전측으로 평가하였다.

• 대한토목학회논문집
• /
• 제32권1A호
• /
• pp.11-18
• /
• 2012

이 논문에서는 유리-에폭시 섬유 보강 복합재료판에 $K_I$ 과 $K_{II}$ 에 의한 혼합모우드 상태의 균열된 알루미늄판의 응력확대계수의 수치해석 산정을 다루고 있다. 응력확대계수 산정을 위한 가상균열닫힘법과 2단계 확장법이 고려된다. 에너지 방출률과 응력확대계수의 항으로 표현되는 파괴역학 매개변수 계산을 위하여, p-수렴 부분 층별모델이 채택된다. 고려되는 p-수렴 방식은 저매개변수 요소의 개념에 기초한다. 1개 층에 대해 가정된 변위장, 변위-변형률 관계, 그리고 3차원 구성방정식은 2차원과 1차원 고차 형상함수의 조합으로 정의된다. 고려되는 요소는 변위장의 보간과 수치적분을 수행하기 위해 로바토 형상함수와 가우스-로바토 적분법이 사용된다. 언급된 모델과 기법들을 사용하여, 경사각도의 변화에 따른 적층판 형상의 효과와 접착제의 강도가 팻치보강 시스템에 미치는 영향이 조사된다. 중립축 변화에 따른 팻치보강 적층판의 면외 휨 효과도 분석된다. 고려되는 모델의 정확성과 단순성 등에 관해서 응력확대계수, 응력분포, 자유도 수, 에너지 방출률 등의 항목을 가지고서 평가된다.