• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.699-704
• /
• 2008

This paper describes a general approach for processing data from an omni-directional guided wave transducer array for the rapid inspection of large plate structures. A basic phased array algorithm is presented that can be applied to any array Geometry. For guided waves on plate, beam steering algorithm is derived and the corresponding beam pattern is analyzed. The algorithms are applied to simulation and experimental data. The results show well its usefulness in structural applications.

• Smart Structures and Systems
• /
• v.7 no.2
• /
• pp.117-132
• /
• 2011

This paper is aimed at presenting two methods on the basis of pattern search and genetic algorithms to detect and estimate damage in plates using the modal data of a damaged plate. The proposed methods determine the damages of plate structures using optimization of an objective function by pattern search and genetic algorithms. These methods have been applied to two numerical examples, namely four-fixed supported and cantilever plates with and without noise in the modal data and containing one or several damages. The obtained results clearly reveal that the proposed methods can be viewed as a powerful and reliable method for structural damage detection in plates using the modal data.

• Proceedings of the KIEE Conference
• /
• 2005.05a
• /
• pp.99-101
• /
• 2005

This paper is concerned with the active vibration control of flexible plate system using $H_2$ controller. The main objective of this paper is to propose the system identification for estimation dynamic equation of plate vibration system and control algorithm such as $H_2$ controller design. In this paper dynamic equation is determined by considering only the first, second, and third vibration modes, and experiments confirm that this model works well. The $H_2$ control algorithm is proposed and implemented on the experimental setup to show their efficacy. Effectiveness and performance of the designed controller was verified by both simulation and experiment result.

• Korean Journal of Computational Design and Engineering
• /
• v.11 no.3
• /
• pp.157-163
• /
• 2006

Surfaces of many engineering structures, especially, those of ships are commonly made out of either single- or double-curved surfaces to meet functional requirements. The first step in the fabrication process of a three-dimensional design surface is unfolding or flattening the surface, otherwise known as planar development, so that manufacturers can determine the initial flat plate which is required to form the design shape. In this paper, an algorithm for optimal approximated development of a general curved surface, including both single- and double-curved surfaces, is established by minimizing the strain energy of deformation from its planar development to the design surface. The unfolding process is formulated into a constrained nonlinear programming problem, based on the deformation theory and finite element. Constraints are subjected to the characteristics of the fabrication method. And the design surface, or the curved shell plate is subdivided by automatic mesh generation.

• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10a
• /
• pp.422-427
• /
• 1988

The purpose of this research is to develope a algorithm characterizing the grasp of the randomly fed objects using the tactile sensor. The tactile sensor used is composed of the 10 x 16 arrays of optical sensors and the planar resolution is 1.8 x 1.8 mm$^{2}$. The square and circular plate are used for the investigation of the characteristics of this sensor. The result shows that the measuring performance of the square plate is superior to that of the circular plate. Based upon this result the algorithm for the assembly of the electric plug was developed and was implemented using the mini-robot.

• Journal of Radiation Protection and Research
• /
• v.26 no.3
• /
• pp.177-181
• /
• 2001

The conversion efficiency of a cesium iodine coated micro-channel plate is studied. We use the EGS4 code to transport photons and generated electrons until their energies become less than 1keV and 10keV respectively. Among the generated electrons, the emission from the secondary electrons located within the escape depth of 56nm from the photo-converter boundary is estimated by integrating the product of the secondary electrons with a probability depending only on their geometric locations. The secondary electron emission from the generated electrons of energy higher than 100eV is estimated by the 'universal yield curve'. The sum of these provides an estimate for the secondary electron yield and we show that results of applying this algorithm agree with known experimental results. Using this algorithm, we computed secondary electron emissions from a micro-channel plate used in a gas electron multiplier detector that is currently being developed at Korea Atomic Energy Research Institute.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.12
• /
• pp.65-73
• /
• 1995

In this paper, new algorithm which calculates transmission coefficient of electromagnetic wave by numerical analysis of scattered field by conductors with arbitrary cross-sections in parallel-plate waveguide is proposed. Proposed algorithm assumes magnetic current distribution on the boundary of scattering conductors, and applies Image theorem to perfect conductor surfaces of parallel-plate waveguide. Integral equations for fictitious magnetic currents on conducting boundary are set up. Magnetic current distributions on conducting boundary are expanded as exponential basis function, and using Galerkin method matrix equations are set wp. To compute matrix elements this method utilizes Fourier transform which is faster than numerical integration. Finally, frequency and incidence-angle characteristic of transmission coefficient are calculated and compared with experimental results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04b
• /
• pp.320-325
• /
• 1995

This study deals with the active vibration control system for an all-clamped rectangular plate with piezoceramic actuators and sensors. A line nonent algorithm (LMA) with the distributed modal sensitivity(DMS) is proposed to reduce the structural vibrations effectively and to select the optimal locations and the optimal directions (skewed angles) of uniform piezoelectric actuators or sensors. Experimental results show that eachmode can attenuated byabout 10 .approx. 13 dB in case a piezoelectric actuator generate the psuedo-random disturbances that excite the plate modes.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.1
• /
• pp.56-63
• /
• 2009

This paper describes a general approach for processing data from an omni-directional guided wave transducer array for the rapid inspection of large plate structures. A basic phased array algorithm is presented that can be applied to any array geometry. For guided waves on plate, beam steering algorithm is derived and the corresponding beam pattern is analyzed. The algorithms are applied to simulation and experimental data. The results show well its usefulness in structural applications.

• Journal of Korea Multimedia Society
• /
• v.20 no.8
• /
• pp.1166-1174
• /
• 2017

In general, the detection of the vehicle license plate is a previous step of license plate recognition and has been actively studied for several decades. In this paper, we propose an algorithm to detect a license plate area of a moving vehicle from a video captured by a fixed camera installed on the road using the Convolution Neural Network (CNN) technology. First, license plate images and non-license plate images are applied to a previously learned CNN model (AlexNet) to extract and classify features. Then, after detecting the moving vehicle in the video, CNN detects the license plate area by comparing the features of the license plate region with the features of the license plate area. Experimental result shows relatively good performance in various environments such as incomplete lighting, noise due to rain, and low resolution. In addition, to protect personal information this proposed system can also be used independently to detect the license plate area and hide that area to secure the public's personal information.