• Steel and Composite Structures
• /
• 제13권4호
• /
• pp.367-382
• /
• 2012

This paper is dedicated to the buckling behaviors of strengthened perforated plates under edge shear loading, which is a typical load pattern of steel plates in civil engineering, especially in plate and box girders. The square plates considered each has a centric circular hole and is simply supported on four edges in the out-of-plane direction. Three types of strengthening stiffeners named ringed stiffener (RS), flat stiffener (FSA and FSB) and strip stiffener (SSA, SSB and SSC) are mainly discussed. The finite element method (FEM) has been employed to analyse the elastic and elasto-plastic buckling behavior of unstrengthened and strengthened perforated plates. Results show that most of the strengthened perforated plates behave higher buckling strengths than the unstrengthened ones, while the enhancements in elastic buckling stress and elasto-plastic ultimate strength are closely related to stiffener types as well as plate geometric parameters including plate slenderness ratio and hole diameter to plate width ratio. The critical slenderness ratios of shear loaded strengthened perforated plates, which determine the practical buckling pattern (i.e., elastic or elasto-plastic buckling) of the plates, are also studied. Based on the contrastive analyses of strengthening efficiency considering the influence of stiffener consumption, the most efficient cutout-strengthening methods for shear loaded perforated square plates with different slenderness ratios and circular hole diameter to plate width ratios are preliminarily identified.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계 학술대회논문집(수송기계편)
• /
• pp.190-193
• /
• 2005

The air filter in engine intake system filters the dirt in the breathing air but also it attenuates the noise although the phenomenon has been regarded negligible. For the analysis of the acoustical performance of air filter, an acoustical model is suggested in this paper. The air filter consists of a porous filter element, which catches the particulate dirt, and a plastic filter box, which supports the filter element. Fibrous structure of the filter element is modeled as a micro-perforated panel using the flow resistivity and porosity. The pleated geometry of the filter element is modeled as two coupled ducts and a mathematical model is developed for the analysis of sound propagation. The filter box Is modeled as a rigid rectangular box. By combining two models, a 4-pole transfer matrix for the air filter is derived. The transmission loss calculated using the transfer matrix of the suggested model is compared with the measured data. Reasonably good agreement is observed. The result can be improved by considering the visco-thermal effect in modeling, in particular at a frequency range near the troughs of TL curve.

• 한국해양공학회지
• /
• 제26권6호
• /
• pp.66-73
• /
• 2012

A pressure compensated chamber of a pilot mining robot isolates and protects an electrical-electronic system from the ambient highly pressured water. Since the inner pressure of the chamber is compensated with outer water pressure using hydraulic oil and pressure compensator, there exists a pressure difference, less than 1 bar, between outer and inner surface. The structural safety of the chamber is obtained relatively easier than the canister type which inner pressure is kept as the atmospheric pressure. However, due to the adoption of box shape for space efficiency and usage of the transparent engineering plastic viewport for checking inner circumstance, the viewport can be largely deformed. This large deformation can cause an additional tensile force, called the prying force, to the bolt-flange connection parts of the viewport. In this paper, we suggest the structural design equation considering the prying action for designing the structure of a box-shape pressure compensated chamber.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 추계학술대회논문집
• /
• pp.32-39
• /
• 1997

The coiling station of ISP coil box is an equipment that winds a hot bar rolled at reduction unit into a coil without mandrel. In the coiling process, the roll gap of the bending unit is a significant one of several factors that influence bar coiling. To obtain a good bar-coil, the roll gap must be set appropriately according to the bar thickness. In this study, with 2-dimensional isothermal elastic-plastic finite element method, authors investigated influence of the change of the roll gap on the initial coiling shapes and the formed inner diameters of coils. Based on finite element analysis, authors proposed the appropriate roll gap according to the bar thickness to be able to wind a hot bar. The inner diameters of coils by results of analysis comparatively agreed with coling operation conducted in plant.

• Journal of Welding and Joining
• /
• 제25권5호
• /
• pp.72-77
• /
• 2007

Prediction and control of the thermal distortion is particularly important for the design and manufacture of welded thin metal structure. In this study, numerical computations are performed to analyze effect of structure section shape and weld line location on distortion. In addition, this study aims to develop a thermal elasto-plastic simulation using finite element method to predict distortion, with particular emphasis on bending deformation generated in outline welding of a thin box structure. From the numerical analysis, it was revealed that the section shape and weld line location play an important role on the welding distortion. Among 3 types of section shape design proposed in this study, the least deformation remained in the two path welded structure.

• 한국작물학회:학술대회논문집
• /
• 한국작물학회 2017년도 9th Asian Crop Science Association conference
• /
• pp.193-193
• /
• 2017

The black heart in potato is a physiological disorder that occurs when potatoes suffer from breathing problems. When storing potatoes at a low temperature around $0^{\circ}C$, there is a high possibility that the respiration rate of potato will rise and black heart will occur. Also, respiration can occur easily and briefly in a state where high temperature and ventilation is insufficient. Recently, as black heart has been occurred continuously and severely in South Korea, here we tried to identify the causes of black heart in potato and to develop the control strategy of this disorder. Firstly, we analyzed the influence on the black heart on the basis of preservation containers (breathable plastic box, burlap bag, paper box, sealed plastic box). After harvesting the potato which is cv. Superior, it preserved for 6 months under conditions of temperature $3.5^{\circ}C{\pm}0.2$ and humidity 85%, after then we surveyed the incidence of emergence rate, rate of weight loss and occurrence rate of black heart. Secondly, in order to investigate the time point of black heart initiation under the oxygen concentration condition of 1% or less, The potatoes were used for this experiment stored for 6 months in a aerated plastic box under conditions of temperature $3.5^{\circ}C{\pm}0.2$ and humidity 85% under sufficient oxygen condition. After stored for 6 month, those were stored at $15^{\circ}C$ and below 1% of oxygen for 25 days, and then the incidence of black heart was surveyed. Thirdly, to investigate the effects of the number of days after harvest on the occurrence of black heart, it was examined the occurrence of black heart stored on 40 days and 100 days after harvesting under sealed condition and vacuum condition. The temperature condition of potato storage was stored was at $4^{\circ}C$ and $25^{\circ}C$ in humidity 85%. As a result of investigating the occurrence of black heart depending on the storage containers, all of the potatoes stored in the sealed plastic box had been occurred black heart. However, black heart of the potatoes in the other treatments did not. Potato preserved under the condition of below 1% of oxygen was found to occur 32% black heart after 25 days of storage. The potatoes corresponding to the required number of days after harvesting were stored for 31 days and the black heart was examined on the occurred. As a result, the potatoes which were 40 days after the harvest did not have black heart under sealed condition and vacuum condition. But potatoes harvested 100 days after harvesting had a black heart incidence of 95.7% under sealed condition at $4^{\circ}C$. The potato placed in the vacuum condition and a sealed state at $25^{\circ}C$ was transformed into anaerobic respiration, the inner tissue of tuber collapsed. Therefore, it is considered that black heart is caused by the breathing trouble in the central part when the oxygen is almost consumed after the aerobic respiration which gradually consumes the oxygen. We conclude that the black heart occurred in the central part where exchange of oxygen and carbon dioxide is the slowest is sensitive to respiration disorder. It is thought that research to investigate black heart generation time according to storage conditions and post-harvest state of potatoes is further necessary.

• Current Research on Agriculture and Life Sciences
• /
• 제33권2호
• /
• pp.41-47
• /
• 2015

본 연구는 온실용 피복재 및 보온재의 조합에 대한 시뮬레이션 해석모델을 개발하여 관류열전달계수를 산정하고 측정된 결과와 비교하여 타당성을 평가하기 위해 수행되었으며 결과를 요약하면 다음과 같다. 유리이중피복의 경우 이중피복 사이의 공기층이 두꺼워짐에 따라 관류열전달계수가 서서히 작아져서 공기층 두께가 25 mm 이상이 되면 관류열전달계수의 변화가 거의 없는 것을 확인할 수 있었다. 또한 온도차가 증가함에 따라 관류열전달계수도 증가하는 것을 확인할 수 있었다. 두 플라스틱 피복재 사이에는 대류에 의한 열전달이 활발하게 일어나기 때문에 비정상 유동에 의한 열전달이 발생하고 이로 인해 온도분포도 비선형적으로 변하는 것으로 사료된다. 플라스틱 피복재 및 보온재들의 간격이 50~200 mm범위에서 변화할 때에 피복재의 간격은 관류열전달계수 큰 영향을 미치지 않는다는 사실을 확인할 수 있었다. 천공복사를 고려한 경우와 고려하지 않은 경우 모두 핫박스의 내외부 온도차가 $30^{\circ}C$인 조건에 대해서는 수치해석결과와 실험결과가 대체로 잘 일치하였다. 따라서 핫박스의 내외부 온도차가 $30^{\circ}C$ 이상인 조건에서 수치해석을 통해 관류열전달계수를 산정한다면 신뢰성 있는 값을 얻을 수 있을 것으로 판단된다.

• 한국응용곤충학회지
• /
• 제57권4호
• /
• pp.253-260
• /
• 2018

토양해충의 포식성 천적인 뿌리이리응애[Stratiolaelaps scimitus (Womersley)]를 이중박스 시스템을 활용하여 대량생산할 수 있는 방법을 개발하였다. 사육상자는 외부(22 L, $54{\times}36{\times}18cm^3$) 및 내부(6.5 L, $31{\times}22{\times}11cm^3$)로 구성된 플라스틱상자이다. 내부상자에는 뿌리이리응애의 은신처 역할을 하는 왕겨(4 L)를 담았다. 외부상자에는 물을 1 L 채우고 그 위에 내부상자를 넣고 외부상자 덮개를 덮었다. 이 시스템은 포식성응애의 탈출을 막고 은신처의 습도를 유지할 수 있다. 천적의 먹이원으로서 긴털가루응애[Tyrophagus putrescentiae (Schrank)]를 쌀겨에 사육하였으며, 뿌리이리응애와 마찬가지로 2중상자에서 증식시켰다. 천적응애상자에 주 1회 먹이응애를 제공하면서 $25{\pm}1^{\circ}C$, 상대습도 $60{\pm}10%$ 조건에서 사육하였다. 뿌리이리응애의 밀도는 4주에 3배로 증가하였으며 최종적으로 약 12만 마리/상자(4 L)였다. 이 방법은 간단한 뿌리이리응애 대량사육기술로서 토양해충의 생물적 방제에 큰 도움이 될 것으로 판단한다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.441-444
• /
• 2003

Polymer concrete has more useful than cement concrete in the strength and durability. So, it is widely utilizing as panel for wall, manhole for communication, foundation and underground connection box, etc. But polymer concrete is a defect that is disadvantageous in economical aspect because cost of resin is expensive. Polymer concrete (PC) using unsaturated polyester resins based on recycled polyethylene terephthalate(PET) plastic waste were used in our study for grasping its mechanical properties such as compressive strength, tensile strength, flexural strength and chemical resistance was tested by dealing with 20% HCl, 30% NaOH. As a result of it, compressive, tensile and flexural strength of PC indicated 752kgf/$\textrm{cm}^2$, 80kgf/$\textrm{cm}^2$ and 243kgf/$\textrm{cm}^2$ kind of satisfaction successively. Also, properties of chemical resistance are superior to those of cement concrete.

• 한국정밀공학회지
• /
• 제15권2호
• /
• pp.68-74
• /
• 1998

In this work, we have been concerned with developing an intelligent mold design system for plastic injection molding on the AutoCAD. We have concentrated on building a viable environment, including a mold parts database and a menu-driven user interface. This provides a more interactive and interface for selection of optimal mold-base and mold parts in mold design system. This work presents a method which allows the designer to select the mold parts and mold-base directly within an AutoCAD environment. It can also automatically generate detailed 3D drawings of the mold parts and mold-base. The system shows its potential capability for future enhancement. Since the system is independent of the data, it could easily be extended to other mold-bases and mold parts. In addition, it can be linked to the molding analysis system by creating subtracted 3-D models.