• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.1
• /
• pp.64-72
• /
• 1998

This paper was undertaken to develop the fracture toughness testing method using small and single specimen compared to the conventional method in evaluating elastic-plastic fracture toughness of the superconducting magnet structural material at cryogenic temperature. The elastic-plastic fracture toughness test was conducted by using the unloading compliance method recommended by ASTM E813-89 to accomplish the above purpose. And, the 20% side-grooved 0.5TCT and 1TCT specimens were used to evaluate the fracture toughness by using as possible as miniaturized CT specimen. The unloading compliance method was a very useful method in evaluating elastic-plastic fracture toughness at cryogenic temperature. It could be taken valid fracture toughness values by using 20% side-grooved 0.5TCT specimen recommended by ASTM E813-89.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.6 no.2
• /
• pp.47-51
• /
• 2007

Special quality of automobile clutch master cylinder(CMC) and analyzed aluminum, plastic material comparison. Efficiency of plastic master cylinder can modularize higher, light weight anger of parts, several piece parts by single parts, prove NVH(Noise, Vibration, Harshness) than aluminum master cylinder as analysis result. Also, structure is easy simplicity, exchange, maintenance costs can be reduced and decrease environmental pollution because recycling is superior. According as content of glass fiber increases, mechanical properties of matter of material increase equally and glass fiber changed variously by condition on manufacturing process. Through comparison analysis with Plastic Body development connection site, did verification.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.214-214
• /
• 2006

The huge amounts of wastes were produced nowadays. Among the solid waste stream, the waste plastic portion is about 20 % in weight, over 50 % in volume. But the most of waste plastics were incinerated or land filled. Only a bit of waste plastics were recycled and reused. On the view point of current energy crisis, this will be an extravagance of beneficial resource. So we should consider the waste plastics as a beneficial raw material. Also need to develop the field of reusing and recycling of post-consumed plastic. In this context, present paper describes the methodology for enhancing or improving the specific properties by way of using inorganic filler waste. Also develop the product from these post-consumed plastic.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.210-213
• /
• 2004

Based on plastic instability, analytical prediction of bursting failure on tube hydroforming processes under combined internal pressure and independent axial feeding is carried out. Bursting is irrecoverable phenomenon due to local instability under excessive tensile stresses. In order to predict the bursting failure, three different classical necking criteria such as diffuse necking criterion for sheet and tube, local necking criterion for sheet are introduced. The incremental theory of plasticity fur anisotropic material is adopted and then the hydroforming limit and bursting failure diagram with respect to axial feeding and hydraulic pressure are presented. In addition, the influences of the material properties such as anisotropy parameter, strain hardening exponent on bursting pressure are investigated. As results of the above approach, the hydroforming limit in view of bursting failure is verified with experimental results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.194-197
• /
• 2002

Applying dual layer insulator on plastic substrates improved electrical characteristics of organic thin film transistor(TFT). A high-quality silicon dioxide(SiO$_2$) suitable for a insulator was deposited on plastic substrates by e-beam evaporation at 110$^{\circ}C$. The insulator film which was treated by N$_2$ annealing at 150$^{\circ}C$ showed excellent I-V, C-V characteristics. The dual layer insulator structure of polyimide-SiO$_2$ improved the roughness of SiO$_2$ surface and showed very low leakage current. In addition, the flat band voltage has been reduced from -2.5V to about 0.5V.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.8
• /
• pp.866-870
• /
• 2004

We have investigated the generation of pretilt angle for a nematic liquid crystal (NLC) alignment with rubbing alignment method on polyimide surfaces using plastic substrates. It was found that monodomain alignment of NLC is obtained with rubbing alignment method on polyimide surfaces using thin plastic substrates. The NLC pretilt angles on thin plastic substrates generated higher than that on glass substrate. Also, EO characteristics of the TN-LCD with a rubbed PI surface based on polymer substrate are almost the same as that of the TN-LCD with a rubbed PI surface based on glass. However, the transmittances of the TN-LCD with a rubbed PI surface based on polymer is less than that with a rubbed PI surface based on g1ass.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.1007-1009
• /
• 2004

We investigated the electro-optical(EO) performances of the super twisted nematic liquid crystal display(STN-LCD) on the polyimide(PI) surface with polymer film using rubbing and photoalignment method. Monodomain alignment of the plastic STN-LCD can be observed. A faster response time for the photoaligned plastic STN-LCD on the polyimide(PI) surfaces can be achieved than rubbingaligned plastic STN-LCD.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.9
• /
• pp.682-685
• /
• 2013

We have fabricated blue phosphorescent organic light-emitting devices (OLEDs) on a plastic substrate. The solution coated poly (9-vinylcarbazole) (PVK) host doped with Bis (3,5-difluoro-2-(2-pyridyl)phenyl_(2-carboxypyridyl)irdium(III) (FIrPic) guest molecules was used as an hole transporting emission layer. The device structure was ITO/PVK:FIrpic (50 nm, xwt%)/TAZ 50 nm)/LiF (0.5 nm)/Al (100 nm). The concentration of FIrpic molecule was varied from 1 wt% to 10 wt%. The OLED on plastic substrate exhibited maximum current efficiency of 18 cd/A with 5 wt% FIrpic molecules were doped into the PVK layer.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.6 no.1
• /
• pp.57-61
• /
• 2007

Special quality of automobile clutch master cylinder(CMC) and analyzed aluminum, plastic material comparison. Efficiency of plastic master cylinder can modularize higher, light weight anger of parts, several piece parts by single parts, prove NVH(Noise, Vibration, Harshness) than aluminum master cylinder as analysis result. Also, structure is easy simplicity, exchange, maintenance costs can be reduced and decrease environmental pollution because recycling is superior. According as content of glass fiber increases, mechanical properties of matter of material increase equally and glass fiber changed variously by condition on manufacturing process. Through comparison analysis with Plastic body development connection site, did verification.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.06a
• /
• pp.100-123
• /
• 1995

The relationship between plastic deformation and crystal grain change in warm forging processes of SM100 carbon steel is studied. If the carbon steel is deformed in warm forging temperature (about recrystallization range), the crystal grain and cementite of the internal part are changed, so material properties are changed. Some experimental values, such as the elliptic degree of cementite, the grain size of cementitie and ferrite grain size, are investigated. When the plastic deformation proceeds, the elliptic degree of cementite becomes large, the grain size of cementite particle is small, and the size of ferrite grain appears fine by recrystallization. The elliptic degree of cementite has a considerable effect on formability. The distribution of effective strain in the forging is calculated by the rigid visco-plastic FEM analysis. The effective strain distribution obtained from the FEM simulation is compared with the experimental result. At effective strain 0.3 dynamic recovery and dynamic recrystallization begin, over 2.5 the organization of material has better quality that is suitable for the following cold forming.