• 한국재료학회지
• /
• 제29권10호
• /
• pp.603-608
• /
• 2019

Plastic waste is becoming a problem in various countries because of the difficulty of natural decomposition. One type is PET plastic(Polyethylene Terephthalate), which is often used as a bottle for soft drink packaging, and LDPE(Low Density Polyethylene), which is also widely used as a food or beverage packaging material. The use of these two types of plastic continuously, without good recycling, will have a negative impact on the environment. Building material waste is also becoming a serious environmental problem. This study aims to provide a solution to the problem of the above plastic waste and building material waste by making them into a mixture to be used as bricks. Research is carried out by mixing both materials, namely plastic heated at a temperature of $180-220^{\circ}C$ and building material waste that had been crushed and sized to 30-40 mesh with homogeneous stirring. The ratios of PET and LDPE plastic to building material waste are 9 : 1, 8 : 2, 7 : 3, 6 : 4 and 5 : 5. After heating and printing, density, water absorption and compressive strength tests are carried out. Addition of PET and LDPE plastic can increase compressive strength, and reduce water absorption, porosity and density. A maximum compressive strength of 10.5 MPa is obtained at the ratio of 6 : 4.

• 한국자동차공학회논문집
• /
• 제8권4호
• /
• pp.149-157
• /
• 2000

Computer simulations of the mechanical behavior of a three point bend specimen with a quarter notch under impact load are performed. The case with a load application point at the side is considered. An elastic-plastic von Mises material model is chosen. Three phases such as impact bouncing and bending phases are found to be identified during the period from the moment of impact to the estimated time for crack initiation. It is clearly shown that no plastic deformation near the crack tip is appeared at the impact phase. However it is confirmed that the plastic zone near the crack tip emerges in the second phase and the plastic hinge has been formed in the third phase. Gap opening displacement crack tip opening displacement and strain rate are compared with rate dependent material(visco-plastic material). The stability during various dynamic load can be seen by using the simulation of this study.

• Steel and Composite Structures
• /
• 제51권4호
• /
• pp.377-389
• /
• 2024

In the present study, thermoelsatoplastic stresses and displacement for rotating hollow disks made of functionally graded materials (FGMs) has been investigated. The linear elastic-fully plastic condition is considered. The material properties except Poisson's ratio are assumed to vary in the radial direction as a power-law function. The heat conduction equation for the one-dimensional problem in cylindrical coordinates is used to obtain temperature distribution in the disk. The plastic model is based on the Tresca yield criterion and its associated flow rules under the assumption of perfectly plastic material behavior. Exact solutions of field equations for elastic and plastic deformations are obtained. It is shown that the elastoplastic response of the functionally graded (FG) disk is affected notably by the radial variation of material properties. It is also shown that, depending on material properties and disk dimensions, different modes of plastic deformation may occur.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 춘계학술대회논문집
• /
• pp.96-100
• /
• 2000

It is difficult to predict material behavior of forming process because the plastic instable flow phenomenon happens in practical forming process I. e. upsetting backward extrusion piercing indentation. In view of the direct relationship between instable material flow and quality defects of the products we should find out their phenomena, In this study we introduced the plastic spin and the kinematic hardening considering the kinematic hardening constitutive equation for rate-dependent material. Also analysis of upset forging is carried out using the rigid plastic FEM with Al7075

• 반도체디스플레이기술학회지
• /
• 제21권3호
• /
• pp.92-97
• /
• 2022

Plastics are classified into 7 types such as PET (PETE), HDPE, PVC, LDPE, PP, PS, and Other for separation and recycling. Recently, large corporations advocating ESG management are replacing them with bioplastics. Incineration and landfill of disposal of plastic waste are responsible for air pollution and destruction of the ecosystem. Because it is not easy to accurately classify plastic materials with the naked eye, automated system-based screening studies using various sensor technologies and AI-based software technologies have been conducted. In this paper, NIR scanning devices considering the NIR wavelength characteristics that appear differently for each plastic material and a system that can identify the type of plastic by learning the NIR spectrum data collected through it. The accuracy of plastic material identification was evaluated through a decision tree-based SVM model for multiclass classification on NIR spectral datasets for 8 types of plastic samples including biodegradable plastic.

• 한국전산구조공학회논문집
• /
• 제13권3호
• /
• pp.361-371
• /
• 2000

RC 구조물은 서로 다른 재료적 특성을 지닌 콘크리트와 철근의 복합구조이고, 특히 콘크리트는 복잡한 소성거동을 나타내는 재료이다. 따라서 RC 구조물의 소성해석을 위해서는 콘크리트와 철근 각각의 재료특성과 소성거동을 묘사할 수 있는 세밀한 모델링 기법이 필요하지만, 이때 발생하는 모델링의 어려움, 모델링 규모, 계산용량 및 수렴성 등의 문제점으로 인하여 소성해석 수행에 많은 시간과 노력이 소요되거나 해석자체가 불가능하게 된다. 따라서 본 논문에서는 간편한 RC 구조물의 소성해석을 위해 RC 부재와 동일한 소성거동을 나타내는 균질·등방 재료로의 물성치환 방법을 제시하였다. 물성치환 원리는 RC 부재의 소성거동 특성, 즉 항복모멘트, 항복곡률 및 극한모멘트, 극한곡률로 표현되는 bi-linear 형태의 모멘트-곡률 관계를 이용하여, 이와 동일한 모멘트-곡률 관계(bi-linear 형태의 응력 변형률 관계)를 갖는 균질·등방 재료를 생성하였다. 또한 실제 RC 부재 해석모델과 치환된 균질·등방 재료를 이용한 해석모델에 대한 소성해석 결과를 비교·분석하여 본 연구의 타당성을 검증하였다.

• 콘크리트학회논문집
• /
• 제22권6호
• /
• pp.825-832
• /
• 2010

철근콘크리트 구조물은 위험 단면이 휨강도에 도달하더라도 이 단면에서 소성힌지가 형성되어 휨모멘트가 재분배되어 곧바로 파괴에 도달하지 않는다. 이러한 소성힌지 영역에서 발생하는 비탄성 변형에 의해 소성 회전이 발생한다. 소성힌지길이는 주로 재료 특성에 영향을 받는다. 이 연구에서는 유로코드2에서 제시하고 있는 재료 모델로부터 산정된 휨곡률 분포로부터 소성힌지길이와 소성회전각을 일관되게 산정하였다. 재료 모델의 한계값 즉, 콘크리트 극한변형률, 철근 극한변형률 및 철근의 경화비(k)가 소성회전능력에 미치는 영향을 분석하였다. 해석 결과 콘크리트 극한변형률 및 철근 극한변형률이 증가함에 따라 소성회전능력이 증가하였고 특히, 철근의 경화비(k)가 증가함에 따라 소성 회전각은 크게 증가되는 것으로 나타났다. 따라서 각 재료 모델의 한계값 결정에 세심한 주의가 필요할 것으로 나타났다.

• Computers and Concrete
• /
• 제26권3호
• /
• pp.227-237
• /
• 2020

Strain rate investigations are needed to calibrate strain-rate-dependent material models and numerical codes. An appropriate material model, which considers the rate effects, need to be used for proper numerical modeling. The plastic concrete cut-off wall is a special underground structure that acts as a barrier to stop or reduce the groundwater flow. These structures might be subjected to different dynamic loads, especially earthquake. Deformability of a structure subjected to dynamic loads is a principal issue which need to be undertaken during the design phase of these structures. The characterization of plastic concrete behavior under different strain rates is essential for proper designing of cut-off walls subjected to dynamic loads. The Cowper-Symonds model, as one of the most commonly applied material models, complies well with the behavior of a plastic concretes in low to moderate strain rates and will be useful in explicit dynamics simulations. This paper aims to present the results of an experimental study on mechanical responses of one of the most useful types of plastic concrete and Cowper-Symonds constant determination procedures in a wide range of strain rate from 0.0005 to 107 (1/s). For this purpose, SHPB, uniaxial, and triaxial compression tests were done on plastic concrete samples. Based on the results of quasi-static and dynamic tests, the dynamic increase factors (DIF) of this material in different strain rates and stress state conditions were determined for calibration of the Cowper - Symonds material models.

• 한국산업융합학회 논문집
• /
• 제25권6_2호
• /
• pp.961-968
• /
• 2022

Hydrogen embrittlement leads to the damages in bolts, nut, especially, high pressure valves, in the semiconductor facilities, hydrogen vehicles, hydrogen stations and so on. Monel material has higher strength than SUS material. Therefore, even though Monel material with special alloy is usually used to prevent the hydrogen embrittlement, it needs powerful drawing system to manufacture the rectangular or hexagonal bar using circular bar. The purpose of this study is to investigate the characteristics of plastic deformation of Monel material and 2 rollers of rolling unit in plastic limit through numerical analysis. As the results, it was predicted that, based on mean stress, as the rolling step was increased, the rolling force of rolling unit was decreased. In addition, the heat treatment for Monel material was needed because of residual stress due to plastic deformation. As for rollers, the roller was safe about 1.86 times compared with that of ultimate strength. In this study, as the roller 2 showed larger stress than roller 1, thus, roller 2 should be designed carefully to guarantee the safety. Further it was confirmed that the reaction force of roller could be helpful in bearing design.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 추계 학술논문 발표대회
• /
• pp.89-94
• /
• 2011

In this research, among thermoplasticity plastic raw material that recycling is possible polyolefine(TPO) and polyvinyl chloride(PVC) as target recycling plan examine wish to. It is polyolefine(TPO) and polyvinyl chloride(PVC)) is mediocrity material that there are a lot of amount useds among plastic material and it is material that recycling is also activated most. Long term made first new regulation raw material, by-product raw material happened at process of production at second factory and third time to examine recycling plan of this material divides this as raw material that pass through process separation and pelet Tuesday and analyzed each special quality removing each removed waste after is used. Measure tension strength and ext. heightening gradually mixing proportion of refreshing resources on standard Sample manufactured as new raw material and application examined possibility availability to single fly system.