• 동력기계공학회지
• /
• 제9권4호
• /
• pp.90-95
• /
• 2005

The wire-arc process is a low-cost thermal spray method simply utilizes electrical energy to melt the feedstock wire. It is more userful for field applications, especially to coat large surface area. In this paper, a special Fe-based alloy coatings by using the wire-arc process were developed. Nanoscale composite coatings were achieved either during spraying or through a post heat treatment. As-sprayed Fe-based alloy coatings had been an amorphous matrix structure, after heating to $700^{\circ}C$ for 10 minutes a solid state transformation occurred in the some fraction of amorphous matrix which resulted in the formation of nanostructured recrystallized phase. Scanning electron microscopy (SEM) and field emotional scanning electron microscope(FE-SEM) were applied to analyze the microstructure of the coatings. Additionally hardness and bend resistance of the Fe-based alloy coatings were examined, and these results were compared with those of partially stabilized zirconia(PSZ) coatings by using the plasma spray process.

• Tribology and Lubricants
• /
• 제39권1호
• /
• pp.13-20
• /
• 2023

Large drill bits may face high hardness ore and high working pressure when working. To optimize the use effect of large drill bits and prolong the use time, it is necessary to add a layer of pressure-resistant, wear-resistant, and low-friction coating on the surface of the drill bit. In this study, CoCrNiAlTi high-entropy alloy coatings and CoCrNiAlTi (70 wt%)-TiC (30 wt%) composite coatings are successfully prepared on Q235 steel by plasma spraying. The CoCrNiAlTi (70 wt%)-TiC (30 wt%) coating consists of FCC solid solution and a small amount of TiC phase. The effect of TiC on the composition phase, microhardness, and elastic modulus of HEA coating is studied by X-ray diffractometer (XRD) and microhardness tester. The effect of TiC on the friction and wear properties of HEA coatings is investigated using a wear tester. By improving the process parameters, the metallurgical bonding between the coating and the substrate is well combined, and a coating without pores and cracks is obtained. The experimental results confirm that the microhardness, elastic modulus, and wear resistance of CoCrNiAlTi-TiC composite coating are better, and the friction coefficient is lower.

• Journal of Welding and Joining
• /
• 제27권2호
• /
• pp.38-43
• /
• 2009

In this study, we investigated photocatalytic ability of plasma sprayed $TiO_2$ and Ag sputtering $TiO_2$(Ag-$TiO_2$) coatings. A sputtering processes were adopted to coat the surface of $TiO_2$ with Ag(99.99%). Ag was sputtered at 10mA, 450V for $1{\sim}11$ seconds. $TiO_2$ and Ag-$TiO_2$ coatings were heat-treated at 250, 300, 350, $400^{\circ}C$ for $0{\sim}240$seconds. Photoelectrical conductivity was measured by four-point probe, and photodegradation was calculated by UV-V is spectrometer. Microstructure observation of $TiO_2$ and Ag-$TiO_2$ coatings were investigated by SEM. Crystal structure of $TiO_2$ and Ag-$TiO_2$ coatings were investigated by XRD. Qualitative analyses of $TiO_2$ and Ag-$TiO_2$ coatings were conducted by EDX. When $TiO_2$ coatings were heat-treated at $350^{\circ}C$ for 30 sec, photoelectrical conductivity and photodegradation were best. And in XRD analysis result, (101)/(110) relative intensity ratio of $TiO_2$(rutile) was comparably changed with photoelectrical conductivity. When Ag-$TiO_2$ coatings were heat-treated at $350^{\circ}C$ for 30 [sec] after sputtering Ag for 7 sec, Photoelectrical conductivity and photodegradation are best. Surface of coatings in such condition has very small and uniform Ag particles.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1999년도 추계학술발표강연 및 논문개요집
• /
• pp.32-32
• /
• 1999

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 추계학술대회 논문집
• /
• pp.457-458
• /
• 2009

• Journal of Welding and Joining
• /
• 제20권4호
• /
• pp.451-458
• /
• 2002

플라즈마 용사법에 의한 섬유강화 복합 소재를 개발하면서 독특한 미세구조가 발견되었다. 이러한 형상은 코팅의 물리적 특성과 직접적으로 관련이 있다고 사료된다 섬유강화 코팅의 구조를 밝히기 위해 고배율 전자현미경이 사용되었으며 분석을 통해 일반적 용사코팅 의 미세구조가 내부에 투입된 강화 섬유(FIBER 또는 WHISKER)에 의해 변형되며 열적으로 anisotropic한 상태로 되었음을 보여주었다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.516.2-516.2
• /
• 2006

• 한국세라믹학회지
• /
• 제39권9호
• /
• pp.851-856
• /
• 2002

산화몰리브덴($MoO_3$)이 첨가된 산화크롬 용사코팅층을 제조하여 산화몰리브덴의 첨가에 따른 고온(450$^{\circ}C$)에서의 플라즈마 용사코팅층에 마찰, 마멸특성을 조사하였다. 마찰, 마멸 특성에 대한 실험을 위하여 왕복동 마멸시험장치를 사용하였다. TEM을 이용하여 코팅층의 미세 구조와 각 상들의 조성을 살펴보았다. 분석 결과에 의하면 산화몰리브덴이 입계로 분산되어 있어 코팅층의 경도와 밀도의 증가가 발생하였다. 마멸시험후 마멸면의 물리적 변화와 화학적 조성의 변화를 SEM와 XPS를 통하여 살펴보았다. 산화몰리브덴이 첨가된 코팅층에서 마찰계수의 감소를 관찰할 수 있었다. 산화몰리브덴이 첨가된 코팅의 마멸된 표면에 마찰, 마멸에 유리한 보호막의 형성이 광범위하게 일어남을 알 수 있었다. 이러한 보호막에 몰리브덴이 산화몰리브덴의 형태로 존재하는 것을 XPS 분석을 통하여 알 수 있었다. 보호막에 산화몰리브덴의 존재가 마찰계수를 감소시키는 것으로 생각된다.

• 한국정밀공학회지
• /
• 제14권1호
• /
• pp.142-149
• /
• 1997

Ceramic-coated anilox roll for printing is resistant to corrosion and wear, and hence has enhanced life and quality. Laser engraving is used typically for machining holes to store ink in this roll. Since engraved hole size and shape are directly related to laser processing parameters, it is necessary to know the rela- tionships among these parameters. In this study, the parameters for engraving of ;oasma sprayed ceramic coatings with Nd:YAG laser were studied. Relationships between hole shape and processing parameters were analyzed. Cr$_{2}$O$_{3}$ceramic was found to be most suitable for Nd:YAG laser engraving. It was found that hole depth can be increased by using higher energy pulses. Effect of using different assistant gases was small to the final results. For better results, it was suggested to use a very stable laser with shorter pulses and higher pulse energy.

• 한국표면공학회지
• /
• 제34권5호
• /
• pp.499-502
• /
• 2001

Functionally gradient NiCrAlY/$ZrO_2$-$Y_2$$O_3$ and NiCrAlY/$ZrO_2$- $CeO_2$-$Y_2$$O_3$ coatings were prepared by APS. The as-sprayed microstructure consisted of metal-rich and ceramic-rich regions, between which $Al_2$$O_3$-rich layers existed owing to the oxidation during APS. During oxidation between 900 and $1100^{\circ}C$ in air, the pre-existing $Al_2$$O_3$-rich scales grew, due mainly to the preferential reaction of Al with inwardly transporting oxygen along the heterogeneous phase boundaries. As the amount of ceramics in the coating increased, the oxidation resistance increased.