• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.244.2-244.2
• /
• 2013

Contact Pattern을 Plasma Etching을 통해 Pattering 공정을 진행함에 있어서 Plasma 내에 존재하는 High Energy Ion 들의 Bombardment 에 의해, Contact Bottom 의 Silicon Lattice Atom 들은 Physical 한 Damage를 받아 Electron 의 흐름을 방해하게 되어, Resistance를 증가시키게 된다. 또한 Etchant 로 사용되는 Fluorine 과 Chlorine Atom 들은, Contact Bottom 에 Contamination 으로 작용하게 되어, 후속 Contact 공정을 진행하면서 증착되는 Ti 나 Co Layer 와 Si 이 반응하는 것을 방해하여 Ohmic Contact을 형성하기 위한 Silicide Layer를 형성하지 못하도록 만든다. High Aspect Ratio Contact (HARC) Etching 을 진행하면서 Contact Profile을 Vertical 하게 형성하기 위하여 Bias Power를 증가하여 사용하게 되는데, 이로부터 Contact Bottom에서 발생하는 Etchant 로 인한 Damage 는 더욱 더 증가하게 된다. 이 Damage Layer를 추가적인 Secondary Damage 없이 제거하기 위하여 본 연구에서는 원자층 식각방법(Atomic Layer Etching Technique)을 사용하였다. 실험에 사용된 원자층 식각방법을 이용하여, Damage 가 발생한 Si Layer를 Secondary Damage 없이 효과적으로 Control 하여 제거할 수 있음을 확인하였으며, 30 nm Deep Contact Bottom 에서 Damage 가 제거될 수 있음을 확인하였다. XPS 와 Depth SIMS Data를 이용하여 상기 실험 결과를 확인하였으며, SEM Profile 분석을 통하여, Damage 제거 결과 및 Profile 변화 여부를 확인하였으며, 4 Point Prove 결과를 통하여 결과적으로 Resistance 가 개선되는 결과를 얻을 수 있었다.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2003.05a
• /
• pp.12-17
• /
• 2003

본 연구에서는 MICP Etching system 을 이용한 Via contact 및 Deep contact hole etch process 특성을 연구하였다. Langmuir probe 를 이용한 MICP source 의 Plasma density & electron temperature 측정하였고 탄소와 플로우르를 포함하는 혼합 Plasma 를 형성하여 RF frequency, wall temperature, chamber gap, gas chemistry 등의 변화에 따른 식각 특성을 조사하였다. Plasma density 는 1000w 에서 $10^{11}$/$cm^3$ 이상의 high density plasma와 uniform plasma 형성을 확인하였고 $CH_{2}F_{2}$와 CO의 적절한 혼합비를 이용하여 Oxide to PR 선택비가 10 이상인 고선택비 조건을 확보하였다. 고선택비 형성에 따라 Polymer 형성이 많이 되었고 이를 개선하기 위하여 반응 챔버의 온도 조절을 통하여 Polymer 증착 방지에 효과적인 것을 확인하였다. MICP source를 이용하여 탄소와 플로우르의 혼합 가스와 식각 챔버의 온도 조절에 의한 선택비 증가를 확보하여 High Aspect Ratio Contact Hole Etch 가능성을 확보하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.104-104
• /
• 2009

Critical dimensions has rapidly shrunk to increase the degree of integration and to reduce the power consumption. However, it is accompanied with several problems like direct tunneling through the gate insulator layer and the low conductivity characteristic of poly-silicon. To cover these faults, the study of new materials is urgently needed. Recently, high dielectric materials like $Al_2O_3$, $ZrO_2$ and $HfO_2$ are being studied for equivalent oxide thickness (EOT). However, poly-silicon gate is not compatible with high-k materials for gate-insulator. To integrate high-k gate dielectric materials in nano-scale devices, metal gate electrodes are expected to be used in the future. Currently, metal gate electrode materials like TiN, TaN, and WN are being widely studied for next-generation nano-scale devices. The TaN gate electrode for metal/high-k gate stack is compatible with high-k materials. According to this trend, the study about dry etching technology of the TaN film is needed. In this study, we investigated the etch mechanism of the TaN thin film in an inductively coupled plasma (ICP) system with $O_2/BCl_3/Ar$ gas chemistry. The etch rates and selectivities of TaN thin films were investigated in terms of the gas mixing ratio, the RF power, the DC-bias voltage, and the process pressure. The characteristics of the plasma were estimated using optical emission spectroscopy (OES). The surface reactions after etching were investigated using X-ray photoelectron spectroscopy (XPS) and auger electron spectroscopy (AES).

• Korean Journal of Materials Research
• /
• v.10 no.3
• /
• pp.179-183
• /
• 2000

The reactive ion etching process of GaN using $BCI_3/H_2/Ar$ high density inductively coupled plasma was investigated. Results showed that both of the etch rate and the sidewall verticality significantly increased as the ICP power, bias voltage, and the $BCI_3$ ratio were increased whereas effects of the other variables were minimal. The maximum etch rate of about 175nm/min was obtained at the condition of ICP power 900W, bias voltage 400V, 4mTorr, and 60% $BCI_3$, which resulted in reasonably smooth etched surface. Etch residues were observed in the case of samples etched at the low bias conditions, which were proposed to be as the $GaCI_x$ compounds.

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.72-74
• /
• 2004

In this study, we used a inductively coupled plasma (ICP) source for etching $Al_2O_3$ thin films because of its high plasma density, low process pressure and easy control bias power. $Al_2O_3$ thin films were etched using $Cl_2/BCl_3$, $N_2/Cl_2/BCl_3$, and Ar/$Cl_2/BCl_3$ plasma. The experiments were carried out measuring the etch rates and the selectivities of $Al_2O_3$ to $SiO_2$ as a function of gas mixing ratio, rf power, and chamber pressure. When $Cl_2$ 50% was added to $Cl_2/BCl_3$ plasma, the etch rate of the $Al_2O_3$ films was 118 nm/min. We also investigated the effect of gas addition. In case of $N_2$ addition, the etch rate of the $Al_2O_3$ films decreased while $N_2$ was added into $Cl_2/BCl_3$ plasma. However, the etch rate increased slightly as Ar added into $Cl_2/BCl_3$ plasma, and then further increase of Ar decreased the etch rate. The maximum etch rate was 130 nm/min at Ar 20% in $Cl_2/BCl_3$ plasma, and the highest etch selectivity was 0.81 in $N_2$ 20% in $Cl_2/BCl_3$ plasma. And, we obtained the results that the etch rate increases as rf power increases and chamber pressure decreases. The characteristics of the plasmas were estimated using optical emission spectroscopy (OES).

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.5
• /
• pp.202-205
• /
• 2010

In this study, the etch properties of $Al_2O_3$ thin films deposited by atomic layer deposition were investigated as a function of the $O_2$ content in $BCl_3$/Ar inductively coupled plasma. The experiments were performed by comparing the etch rates and selectivity of $Al_2O_3$ over the hard mask materials as functions of the input plasma parameters, such as the gas mixing ratio, DC-bias voltage, ratio-frequency (RF) power and process pressure. The highest obtained etch rate was 477 nm/min at an RF power of 700 W, $O_2$ to $BCl_3$/Ar gas ratio of 15%, DC-bias voltage of -100 V and process pressure of 15 mTorr. The deposition occurred on the surfaces when the amount of $O_2$ added to the $BCl_3$/Ar gas was too high at a low DC-bias voltage or high process pressure. X-ray photoelectron spectroscopy was used to investigate the chemical reactions on the etched surface.

• Journal of the Korean institute of surface engineering
• /
• v.41 no.3
• /
• pp.83-87
• /
• 2008

This study described the effects of RF power, DC bias voltage, chamber pressure and gas mixing ratio on the etch rates of TiN thin film and selectivity of TiN thin film to $SiO_2$ with $BCl_3$/Ar gas mixture. When the gas mixing ratio was $BCl_3$(20%)/Ar(80%) with other conditions were fixed, the maximum etch rate of TiN thin film was 170.6 nm/min. When the DC bias voltage increased from -50 V to -200 V, the etch rate of TiN thin film increased from 15 nm/min to 452 nm/min. As the RF power increased and chamber pressure decreased, the etch rate of TiN thin film showed an increasing tendency. When the gas mixing ratio was $BCl_3$(20%)/Ar(80%) under others conditions were fixed, the intensity of optical emission spectra from radical or ion such as Ar(750.4 nm), $Cl^+$(481.9 nm) and $Cl^{2+}$(460.8 nm) was highest. The TiN thin film was effectively removed by the chemically assisted physical etching in $BCl_3$/Ar ICP plasma.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.105-105
• /
• 2009

$ZrO_2$ is one of the most attractive high dielectric constant (high-k) materials. As integrated circuit device dimensions continue to be scaled down, high-k materials have been studied more to resolve the problems for replacing the EY31conventional $SiO_2$. $ZrO_2$ has many favorable properties as a high dielectric constant (k= 20~25), wide band gap (5~7 eV) as well as a close thermal expansion coefficient with Si that results in good thermal stability of the $ZrO_2/Si$ structure. In order to get fine-line patterns, plasma etching has been studied more in the fabrication of ultra large-scale integrated circuits. The relation between the etch characteristics of high-k dielectric materials and plasma properties is required to be studied more to match standard processing procedure with low damaged removal process. Due to the easy control of ion energy and flux, low ownership and simple structure of the inductively coupled plasma (ICP), we chose it for high-density plasma in our study. And the $BCl_3$ included in the gas due to the effective extraction of oxygen in the form of $BCl_xO_y$ compound In this study, the surface kinetic properties of $ZrO_2$ thin film was investigated in function of Ch addition to $BCl_3/Ar$ gas mixture ratio, RF power and DC-bias power based on substrate temperature. The figure 1 showed the etch rate of $ZrO_2$ thin film as function of gas mixing ratio of $Cl_2/BCl_3/Ar$ dependent on temperature. The chemical state of film was investigated using x-ray photoelectron spectroscopy (XPS). The characteristics of the plasma were estimated using optical emission spectroscopy (OES). Auger electron spectroscopy (AES) was used for elemental analysis of etched surface.

• Journal of the Korean institute of surface engineering
• /
• v.41 no.5
• /
• pp.189-193
• /
• 2008

In this study, we carried out an investigation of the etching characteristics (etch rate, selectivity to $SiO_2$ and $HfO_2$) of TiN thin films in the $CH_4$/Ar inductively coupled plasma. The maximum etch rate of $274\;{\AA}/min$ for TiN thin films was obtained at $CH_4$(80%)/Ar(20%) gas mixing ratio. At the same time, the etch rate was measured as function of the etching parameters such as RF power, Bias power, and process pressure. The X-ray photoelectron spectroscopy analysis showed an efficient destruction of the oxide bonds by the ion bombardment as well as showed an accumulation of low volatile reaction products on the etched surface. Based on these data, the ion-assisted chemical reaction was proposed as the main etch mechanism for the $CH_4$ containing plasmas.

• Journal of the Korean Vacuum Society
• /
• v.1 no.1
• /
• pp.145-152
• /
• 1992

Si surfaces exposed to CHF3/C2F6 gas plasmas ih reactive ion etching (RIE) have been characterized by X-ray photoelectron spectroscopy (XPS). CHF3/C2F6 gas plasma exposure of Si surface leads to the deposition of residual film containing carbon and fluorine. The narrow scan spectra of C 1s show various bonding states of carbon as C-Si, C-F/H, C-CFx(x $\leq$ 3), C-F, C-F2, and C-F3. The chemical bonding states of fluorine are described with F-Si, F-C and F-O. And the oxygen and silicon are also detected. The effects of parameters for reactive ion etching as CHF3/C2F6 gas ratio, RF power, and pressure are investigated.