• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1364-1366
• /
• 1997

Planar type magnetized inductively coupled plasma etcher has been built. The density and temperature of Ar plasma are measured as a function of rf power, external magnetic field, and pressure. The oxide etch rate and selectivity to polysilicon are measured as the above mentioned conditions and self-bias voltage.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.4
• /
• pp.261-266
• /
• 1998

In developing the high density memory device, the etching of fine pattern is becoming increasingly important. Therefore, definition of ultra fine line and space pattern and minimization of damage and contamination are essential process. Also, the high density plasma in low operating pressure is necessary. The candidates of high density plasma sources are electron cyclotron resonance plasma, helicon wave plasma, helical resonator, and inductively coupled plasma. In this study, planar type magnetized inductively coupled plasma etcher has been built. The density and temperature of Ar plasma are measured as a function of rf power, flow rate, external magnetic field, and pressure. The oxide etch rate and selectivity to polysilicon are measured as the above mentioned conditions and self-bias voltage.

• Journal of the Korean Vacuum Society
• /
• v.20 no.5
• /
• pp.322-326
• /
• 2011

Etch process of silicon dioxide layer by using capacitively coupled plasma (CCP) is currently being used to manufacture semiconductor devices with nano-scale feature size below 50 nm. In typical CCP plasma etcher system, plasmas are generated by applying the RF power on upper electrode and ion bombardment energy is controlled by applying RF power to the bottom electrode with the Si wafer. In this case, however, etch results often drift due to heating of the electrode during etching process. Therefore, controlling the temperature of the upper electrode is required to obtain improvement of etch repeatability. In this work, we report repeatability improvement during the silicon dioxide etching under extreme process conditions with very high RF power and close gap between upper and bottom electrodes. Under this severe etch condition, it is difficult to obtain reproducible oxide etch results due to drifts in etch rate, critical dimension, profile, and selectivity caused by unexpected problems in the upper electrode. It was found that reproducible etch results of silicon dioxide layer could be obtained by controlling temperature of the upper electrode. Methods of controlling the upper electrode and the correlation with etch repeatability will be discussed in detail.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2008.08a
• /
• pp.284-284
• /
• 2008

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.922-925
• /
• 1999

The Silylation photo-resist etch process was tested by Enhanced-ICP dry etcher. The comparison of the two process results of micro pattern etching with 0.25${\mu}{\textrm}{m}$ CD by E-ICP and ICP reveals that E-ICP has better quality than ICP The etch rate and the microloading effect was improved in E-ICP Especially, the problem of the lateral etch was improved in E-ICP.

• Applied Science and Convergence Technology
• /
• v.26 no.6
• /
• pp.184-188
• /
• 2017

Polymer deposition pattern on the ceramic lid surface is analyzed by numerical modeling. Assumption was made that is affected by gas flow pattern from the horizontal and vertical nozzles, temperature profile from the finger-like branches made of graphite and electrostatic potential effect. Calculated results showed gas flow dynamics is less relevant than two others. Temperature and electrostatic effects are likely determining the polymer deposition pattern based on our numerical simulation results.

• Applied Science and Convergence Technology
• /
• v.24 no.2
• /
• pp.27-32
• /
• 2015

We analyzed the destruction patterns of a turbo-molecular pump (TMP) resulting from its sudden exposure of a foreline to the atmospheric pressure due to a destruction of the foreline connecting clamp of an ICP dry etcher for 300 mm wafers during high-vacuum operation ($5{\times}10^{-6}$ Torr). Unlike in the case of view port's breakage, the TMP's rotor module was crashed inside the chamber. The primary damage resulted from the collision of the blades and stators, and the secondary damage resulted from the breaking of the rotor - driving shaft assembly. The fixing screws of the rotor and axial shaft were bent and broken when the TMP controller output the maximum current even after the crash event. Electrical power consumption analysis of the TMP power controller confirmed it. The stress distributions were analyzed by a finite element method using CFD-ACE+ multi physics software. Rotating inertia of each parts and kinetic energies were calculated as well. 68% of the rotational kinetic energy is deposited by the rotor - shaft module.

• Journal of the Korean Vacuum Society
• /
• v.1 no.1
• /
• pp.37-42
• /
• 1992

Abstract-The ECR(E1ectron Cyclotron Resonance) plasma etcher was developed for process of manufacturing 16M164' DRAM and applied to poly-Si etching process. The etching rate and selectivity of poly-Si were investigated by changing the process factor of pressure gas and microwave power. The increasing power of microwave will have the trend of increasing the etching rate and selectivity of Oxide, and have suitable value process pressure at 6 mTorr. The increasing value of process gas SFdSF6+ Clz will cause the decrease of etching rate and selectivity, this is because the best process factor is not found.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2000.04a
• /
• pp.87-96
• /
• 2000

The properties of polyimide for interlayer dielectric applications are investigated during plasma etching of aluminum on it. Chlorine-based plasma generally used for aluminum etching results in an increase in the (dielectric constant of polyimide, while $SF_6$ plasma exhibits a high polyimide etch rate and a reducing effect of the dielectric constant. The leakage current of polyimide is significantly suppressed after plasma exposure. An optimal combination of Al etch with $Cl_6$ plasma and polyimide etch with $SF_6$ plasma is expected to be a good tool for realizing multilevel metallization structures.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2000.04a
• /
• pp.97-102
• /
• 2000

We have studied etching characteristic of Ta film using Electron Cyclotron Resonance (ECR) etcher system. Microwave source power. RF bias power. and working pressure were varied to investigate the etch Profile. And we have used two step etching method to acquire the goWe have studied etching characteristic of Ta film using Electron Cyclotron Resonance (ECR) etcher system. Microwave source power. RF bias power. and working pressure were varied to investigate the etch Profile. And we have used two step etching method to acquire the good etch profile preventing the microloading effect.od etch profile preventing the microloading effect.