• Journal of the Korean Vacuum Society
• /
• v.17 no.2
• /
• pp.96-101
• /
• 2008

The magnesium oxide (MgO) protective layer plays an important role in plasma display panels (PDPs). Our previous work demonstrated that the properties of MgO thin film could be improved, which were deposited by Ion-Beam-Assisted Deposition (IBAD). However arc discharge always occurs during the IBAD process. To avoid this problem, Oxygen-Neutral-Beam-Assisted Deposition (NBAD) is used to deposit MgO thin films in this paper. The energy of the oxygen neutral beam was used as the parameter to control the deposition. The experimental results showed that the oxygen neutral beam energy was effective in determining in structural and discharge characteristics. The lowest firing inception voltage, the highest brightness and the highest luminous efficiency were obtained when the MgO thin film was deposited with an oxygen neutral beam energy of 300eV. The surface morphology of MgO thin film was also analyzed using AFM (Atomic Force Microscopy) and SEM (Scanning Electron Microscopy).

• Applied Chemistry for Engineering
• /
• v.10 no.8
• /
• pp.1114-1118
• /
• 1999

Barrier rib for the plasma display panel(PDP) was made by photolithographic process utilizing photosensitive barrier rib paste. The barrier rib paste was prepared by first dissolving ethylcellulose(binder polymer) in butyl carbitol(BC)/butyl carbitol acetate(BCA) =30/70 wt % mixture solvent at 15 wt % concentration. To this solution a mixture of functional monomers consisted of tripropyleneglycol diacrylate/ pentaerythritol triacrylate = 50/50 wt %, Irgacur 651 photoinitiator, and barrier rib powder were added and then the whole mixture was mixed in the three roll mill for 2 hr. The effect of component and concentration of photosensitive barrier paste on the photolithographic process was studied. After optimization of the paste formulation and photolithographic process, barrier rib could be obtained with good resolution up to $100{\mu}m$ height.

• Korean Journal of Optics and Photonics
• /
• v.12 no.2
• /
• pp.103-108
• /
• 2001

In this paper, we designed and made the scanned point detecting system for 3-dimensional measurement of the light emitted from plasma display panel (PDP) , and we measured and analyzed 3-dimensional light emitted from a real PDP by using this scanned point detecting system. The scanned point detecting system has a point detector with a pinhole. The light emitted from the source at the in-focus position can pass through the pinhole and be collected by detector. The light from other sources at outof-focus positions is focused at points in front of or behind the pinhole, and thus it is intercepted by the pinhole. Therefore, we can detect light information from a particular point of a PDP cell of 3-dimensional structure. We know the electric field distribution inside the PDP cell from the 3-dimensionallight intensity distribution measured by using the scanned point detecting system. As the Z axial measurement increases, the intensity of light detected increases and intensity of light detected on the inside edge of the ITa electrode is larger than outside edge of the ITa eletrode and gap of the ITa electrodes. Also, as the measurement point moves from one barrier rib to another, the detected light is weaker near to the barrier ribs than at the center between the barrier ribs. The emitted light is concentrated at the center between barrier ribs. ribs.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.6
• /
• pp.497-501
• /
• 2005

Dry film method was applied to fabricate lead-free transparent dielectric fur PDP(Plasma Display Panel). From various slurry compositions, it was able to find out the. best composition for producing high density green sheet. The slurry exhibited shear thinning characteristics which are known to be suitable fur producing a high quality green sheet. The thermal expansion coefficient of the fabricated transparent dielectric was measured to be $97{\times}10^{-7}/^{\circ}C$ which is close to the value of the glass substrate(PD-200). Cross sectional SEM of the transparent dielectric layer on PD-200 showed that the two layers were well attached each other with no observable gaps between them.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.8
• /
• pp.27-33
• /
• 2007

A novel priming discharge technique in which the ramp shaped priming pulse is superposed on the sustain period so that the entire plasma display panel (PDP) is discharged at the same time with a single drive circuit is proposed. From the experimental results, it is ascertained that the priming discharge is ignited only in a pixel in which sustain discharge does not occur and it has been understood that the priming pulse hardly influences the sustain discharge. Moreover, high-speed driving with address pulse widths of 0.7[${\mu}s$] was achieved and a wide address voltage margin of 40[V] was obtained by using the drive method applied the proposed priming discharge technique. In these results, full-HDTV PDP with 1080 horizontal scanning lines can be driven without decreasing the brightness and the possibility of the commercializing is also high because this technology is designed for using the commercialized driver IC.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.2
• /
• pp.194-202
• /
• 2005

This paper proposes a new multi-level energy recovery sustaining driver for AC PDP(Plasma Display Panel), which solves the problems and maintains the merits of the conventional multi-level sustaining driver. While the conventional circuit improves the hard switching in the Weber circuit, there exist parasitic resonant currents in resonant inductors and Vs/2 sustaining period. Comparing the proposed circuit with the conventional circuit, the number of inductors are reduced by half, the parasitic resonant currents in resonant inductors are eliminated, and the hard switching problem is solved by CIM(Current Injection Method). Moreover the voltages across series-connected switching elements in the full bridge circuit are distributed equally by adopting NPC(Neutral Point Clamping) techniques. And circuit operations of the proposed circuit are analyzed for each mode and the validity is verified by the simulations using PSpice program and experimentation with a prototype drive circuit.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.31-34
• /
• 2009

We investigated the effect of relative dielectric constant of front dielectric layer on the efficacy of plasma display panel. Dielectric materials with relative dielectric constant of around 6 and 7 were developed. When the front dielectric layer had a low relative dielectric constant, power consumption decreased more than luminance did. And it led to efficacy enhancement. However, the minimum sustain voltage increased.

• Journal of Information Display
• /
• v.3 no.1
• /
• pp.11-16
• /
• 2002

This paper presents a study on the tubeless Plasma Display Panel (PDP) packaging using glass-to-glass electrostatic bonding with intermediate amorphous silicon. The bonded sample sealing the mixed gas with three species showed high strength ranging from 2.5 MPa to 4 MPa. The glass-to-glass bonding for packaging was performed at a low temperature of $180^{\circ}C$ by applying bias of 250 $V_{dc}$ in ambient of mixed gases of He-Ne(27 %)-Xe(3 %). The tubeless packaging was accomplished by bonding the support glass plate of $30mm{\times}50mm$ on the rear glass panel and the capping glass of $20mm{\times}20mm$. The 4-inch color AC-PDP with thickness of 8 mm was successfully fabricated and fully emitted as white color at a firing voltage of 190V.

• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.425-429
• /
• 2004

A new multi-level type energy recovery sustaining driver for AC PDP(Plasma Display Panel) is proposed in this paper. The multi-level driver has been developed to reduce the voltage stress on switching elements. Comparing the proposed driver with the conventional multi-level driver, 4 switching elements, 4 diodes, and two auxiliary capacitors are eliminated in the viewpoint of circuit structure. Moreover, the voltage stress on switching elements is more reduced and the sustain period is extended. To verify the validity of the proposed energy recovery circuit, computer simulations using PSpice program are carried out.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.1
• /
• pp.65-72
• /
• 2002

Generally, there are laser operating equipments( aligner, stepper) and electronic microscope( SEM, TEM) as a high precision manufacturing and inspection equipment in semiconductor production companies, precision examination and measuring laboratories. Mostly, these equipments are characterized by projection and target part. The relative displacements between projection and target part are dominant roles in vibrational problem in these precision equipments. These relative displacements are determined by the position of incoming vibration and the difference of vibration response in projection and target part. In this study, the allowable vibrational limits are suggested and the vibrational reduction plans are proposed by measurement and analysis of vibration phenomenon in the Clean Room in PDP(plasma display panel) production building. The vibration performance is evaluated by comparison relative displacements between projection and target part before/after the vibration isolation plan.