• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.2
• /
• pp.122-129
• /
• 2004

There is an increasing need for large flat panel display devices. PDP (Plasma Display Panel) is one of the most promising candidates for this need. Thermal shock failure of PDP glass during manufacturing process is a critical issue in PDP industry since it is closely related to the product yield and the production speed. In this study, thermal shock resistance of PDP glass is measured by water quenching test and an analysis scheme is described for estimating transient temperature and stress distributions during thermal shock. Based on the experimental data and the analysis results, a simple procedure for predicting the thermal shock failure of PDP glass is proposed. The fast cooling process for heated glass plates can accelerate the speed of PDP production, but often leads to thermal shock failure of the glass plates. Therefore, a design guideline for preventing the failure is presented from a viewpoint of high speed PDP manufacturing process. This design guideline can be used for PDP process design and thermal -shock failure prevention.

• Journal of Information Display
• /
• v.4 no.4
• /
• pp.19-24
• /
• 2003

By using vacuum in-line driving and photoluminescence measuring system, we have examined the electrical and optical characteristics of plasma display panel produced by vacuum in-line sealing technology. In addition, the relationship between luminous efficiency and base vacuum level before filling discharge gas was analyzed. In the case of base vacuum level of $1.33{\times}10^{-1}$ Pa, the firing voltage of a 2-inch diagonal PDP panel was ranged from 312 to 343 V depending on the discharge gas pressure of $2.667{\times}10^4$ to $4{\times}10^4$ Pa at room temperature, Whereas in the case of $1.33{\times}10^{-4}$ Pa, the firing voltage was reduced by 40 V and luminescence was improved slightly.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.510-514
• /
• 1997

The thin film that is electrically conductive and optically transparent is called conductive transparent thin film. ITO(Indium-Tin Oxide) which is a kind of conductive transparent thin film has been widely used in solar cell, transparent electrical heater, selective optical filter, FDP(Flat Display Panel) such as LCD(Liquid Crystal Display), PDP(Plasma Display Panel) and so on. Especially in PDP, ITO films is used as a transparent electrode in order to maintain discharge and decrease consumption power through the improvement of cell structure. In this study, we prepared ITO by reactive r.f. sputtering with indium-tin(Sn 10wt%) alloy target instead of indium-tin oxide target. The ITO films deposited at low temperature 15$0^{\circ}C$ and 8% $O_2$. Partial pressure showed about 3.6 Ω/$\square$. At the end of firing, the resistance of ITO was decreased, the optical transparence was improved above 90%.

• Journal of Information Display
• /
• v.2 no.1
• /
• pp.14-19
• /
• 2001

Plasma display panel(PDP) have gained great attention due to their potential application to large-area display including HDTV. The luminance and luminous efficiency of PDP, however, should be improved to realize this goal. In this study, we examined experimentally the effects of phosphor thickness and discharge gap on the luminance and luminous efficiency of ac PDP. For the rib height of 110 ${\mu}m$, whereas the optimum phosphor thickness was about 30 ${\mu}m$. The optimum thickness of green phosphor was about 50 ${\mu}m$ for the rib height of $120{\sim}160\;{\mu}m$.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.380-384
• /
• 2005

Plasma display panel (PDP) has a serious thermal problem, because the luminance efficiency of the conventional PDP is about 1.5 lm/W and it is less than $3{\sim}5$ lm/W of cathode ray tube (CRT). Thus there is a need for improving the luminance efficiency of the PDP There are several approaches to improve the luminance efficiency of the PDP and we adopt the driving PDP at high frequency range from 400 kHz up to over 700 kHz. Since a PDP is regarded as an equivalent inherent capacitance, many types of sustaining drivers have been proposed and widely used to recover the energy stored in the PDP. However, these circuits have some drawbacks for driving PDP at high frequency range. In this paper, we investigate the effect of the parasitic components of PDP itself and driver when the reactive energy of panel is recovered. Various drivers are classified and evaluated whether it is suitable for high frequency driver, and finally current-fed type with do input voltage biased is proposed. This driver overcomes the effect of parasitic component in panel and driver and fully achieves ZVS of all full-bridge switches and reduces the transition time of the panel polarity.

• Journal of Power Electronics
• /
• v.9 no.6
• /
• pp.884-891
• /
• 2009

An address voltage stabilization circuit for the single-side driving (SSD) method for AC plasma display panels (PDP) is proposed. The single-side driving method, which eliminates a common sustaining driver, uses only two electrodes in a three electrode AC PDP structure. The high-impedance (Hi-Z) mode operation of the data drive ICs during the sustaining period is needed for surface gas-discharge without misfiring in the SSD method but it produces the problem that the address voltage increases up to the breakdown voltage. The proposed circuit based on a flyback converter can stabilize the address voltage under the breakdown voltage and provide better surface gas-discharge performance without any misfiring in the SSD scheme.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.1948-1950
• /
• 2005

In the recent years, much interests and attraction has been paid on the plasma display panel. To achieve high performance display panel, there has been a strong demands for studies on the transparent conducting films such as ITO and ZnO. In this study, we propose PDP cell with ZnO transparent conducting electrode. The electrical and optical characteristics of PDP cell with ZnO transparent electrode were studied and compared with that of conventional ITO electrode.

• Journal of the Semiconductor & Display Technology
• /
• v.11 no.1
• /
• pp.67-71
• /
• 2012

The optical properties of PDP, such as the transmittance and reflectance, were analyzed with 3D optical code. Three different ITO-less structures in the front panel are examined. In the assembled panel study, the test 1 structure shows 16.6% and 10.2% higher reflectance than the structures of tests 2 and 3, respectively. In order to check the validation of the simulation result, three 7.5-inch test panels having the same geometry and property are fabricated as simulation models. The calculated reflective properties are compared to the measured data from real panels. The relative difference extracted from the simulation and measurement methods is less than 4.9% and are well matched.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.69-72
• /
• 2008

A new electrode structure is proposed in this paper which can increase the discharge efficiency of plasma display panels and also decrease the panel capacitance by decreasing the electrode area effectively. Even with the decreased electrode area, the proposed structure could suppress the requirement for increasing the voltage and improve efficiency by limiting the discharge current.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1207-1210
• /
• 2005

The MgO protective layer provides protection from the discharge, lowers the discharge voltage and prolongs the AC-PDP lifetime. We have investigated the characteristics of degradation of MgO protective layer, which correlates to the image-sticking[1] and the lifetime in AC-PDP. The degraded MgO have been changed the surface morphology of MgO. It was found that panel lifetime depended on degradation of MgO protective.