• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.76-85
• /
• 1998

Recently, Genetic Algorithm(GA) is widely adopted into a search procedure for structural optimization, which is a stochastic direct search strategy that mimics the process of genetic evolution. This methods consist of three genetics operations maned selection, crossover and mutation. Contrast to traditional optimal design techniques which use design sensitivity analysis results, GA, being zero-order method, is very simple. So, they can be easily applicable to wide area of design optimization problems. Also, owing to multi-point search procedure, they have higher probability of converge to global optimum compared to traditional techniques which take one-point search method. In this study, a method of finding the optimum values of suspension parameters is proposed by using the GA. And vehicle is modelled as planar vehicle having 5 degree-of-freedom. The generalized coordinates are vertical motion of passenger seat, sprung mass and front and rear unsprung mass and rotate(pitch) motion of sprung mass. For rapid converge and precluding local optimum, share function which distribute chromosomes over design bound is introduced. Elitist survival model, remainder stochastic sampling without replacement method, multi-point crossover method are adopted. In the sight of the improvement of ride comfort, good result can be obtained in 5-D.O.F. vehicle model by using GA.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.2
• /
• pp.172-177
• /
• 2004

In this paper, DGS(Defected Ground Structure) is applied to multi-layer structure using LTCC(Low Temperature Co-fired Ceramics). Sprial DGS is adopted in order for size-reduction and higher quality factor, the multi-layer DGS has the same characteristics as the planar DGS. Multi-layer bandpass filter of new shape is confiured using two multi-layer spiral DGS and is designed with no via-hole for the simple process. 5.25 GHz Wireless LAN bandpass filter is designed and fabricated, the insertion loss of the filter is measured less than 1.5 dB, and the size is 2.0 mm${\times}$1.2 mm${\times}$1.1 mm(L${\times}$W${\times}$H).

• Computational Structural Engineering
• /
• v.9 no.3
• /
• pp.145-155
• /
• 1996

This paper suggests a new algorithm of automatic mesh generation over planar domains with arbitrarily shaped boundaries and control curves. The algorithm is based on the method of recursively subdividing the domain by the path connecting, with minimum penalty value, two points on the super-loop, which consists of the boundaries and the control curves, The algorithm is not subject to any limitation on the shape of the domain, and its process can be fully automated. Therefore, this algorithm can be implemented into computer programs which require minimal user intervention while generating finite element meshes over complicated domains. This algorithm can also be easily extended for application to the generation of meshes over curved surfaces, or to the adaptive mesh generation.

• International Journal of CAD/CAM
• /
• v.9 no.1
• /
• pp.37-46
• /
• 2010

Existing methods for the registration of blurred images are efficient for the artificially blurred images or a planar registration, but not suitable for the naturally blurred images existing in the real image mosaic process. In this paper, we attempt to resolve this problem and propose a method for a distortion-free stitching of naturally blurred images for image mosaic. It adopts a multi-resolution and robust feature based inter-layer mosaic together. In each layer, Harris corner detector is chosen to effectively detect features and RANSAC is used to find reliable matches for further calibration as well as an initial homography as the initial motion of next layer. Simplex and subspace trust region methods are used consequently to estimate the stable focal length and rotation matrix through the transformation property of feature matches. In order to stitch multiple images together, an iterative registration strategy is also adopted to estimate the focal length of each image. Experimental results demonstrate the performance of the proposed method.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.296-296
• /
• 2013

Supercapacitor is a capacitor with extraordinarily high energy density, which basically consists of current collector, active material and electrolyte. Ruthenium oxide ($RuO_2$) is one of the most widely studied active materials due to its high specific capacitance and good electrical conductivity. In general, it is known that the coating of $RuO_2$ on nanoarchitectured current collector shows improved performance of energy storage device compared to the coating on the planar current collector. Especially, the surface structure with standing coaxial nanopillars are most desirable since it can provide direct paths for efficient charge transport along the axial paths of each nanopillars and the inter-nanopillar spacing allows easy access of electrolyte ions. However, well-known fabrication methods for metal or metal oxide nanopillars, such as the process using anodize aluminum oxide (AAO) templates, often require long and complicated nanoprocess.In this work, we developed relatively simple method fabricating indium tin oxide (ITO) nanopillars via sputtering. We also electrodeposited $RuO_2$ nanoparticles onto these ITO nanopillars and investigated its physical and electrochemical properties.

• Journal of the Korean Ceramic Society
• /
• v.17 no.2
• /
• pp.80-88
• /
• 1980

The sintering phenomena and piezoelectric properties of PZT ceramics of composition $Pb(Zr_{0.54} Ti_{0.46})O_3$ were investigated when a small quantity of $La_2O_3$ , $LaMnO_3$, $LaCrO_3$ were added. The unwanted chemical composition change in PZT during sinterin porces du to PbO evaporation poses a severe problem in PZt manufacturinig. It is observed tat an addition of small amount of $LaMnO_3$ to PZT markedly decreases the evaporation of PbO during sintering . The green compact of (1-x) PZT.xLaMnO3(x=0.02~0.10) could be sintered of under O2 atmosphere alone with no significant loss of PbO. The planar coupling factor kp of the sintered $0.98Pb(Zr_{0.54} Ti_{0.46})O_{3.0.02}LaMnO}3$ is similar to that of commercial PZT 6A. Microstructure investigation shows that part of sintering process of $Pb(Zr, Ti)O_3$.$LaMnO_3$ system progresses via liquid phase sintering. It is believed that the evaporation of PbO in PZT sintering is restricted by the addition of $LaMnO_3$ due to the above phenomena. Furthermore the solid solution of $LaMnO_3$ in PZT causes diffuses phase transition.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.2032-2034
• /
• 2000

The performance of ac plasma display panels (PDP) is influenced strongly by the surface glow discharge characteristics on the MgO thin films. This paper deals with the surface slew discharge characteristics and some physical properties of MgO thin films prepared by reactive RF planar unbalanced magnetron sputtering in connection with ac PDP. The samples prepared with the do bias voltage of -10V showed lower discharge voltage and lower erosion rate by ion bombardment than those samples prepared by conventional magnetron sputtering or E-beam evaporation. The main factor that improves the discharge characteristics by bias voltage is considered to be due to the morphology changes or crystal structure of the MgO thin film by ion bombardment during deposition process.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.6
• /
• pp.101-109
• /
• 2005

Ultra-precision positioning systems basically require high natural frequency and sufficient workspace. To cope with this requirement, flexure hinge mechanisms have been proposed. However, previous designs are hard to satisfy the functional requirements of the system due to difficulty in modeling and optimizing process applying an independent axiomatic design. Therefore, this paper proposes a new design and design-order based on semi-coupled axiomatic design. A planar 3 DOF parallel type micro mechanism is chosen as an exemplary device. Based on preliminary kinematic analysis and dynamic modeling of the system, an optimal design has been carried out. To check the effectiveness of the optimal parameters obtained from theoretical approach, simulation is performed by FEM. The simulation result shows that a natural frequency of 200.53Hz and a workspace of $2000{\mu}m{\times}2000{\mu}m$ can be ensured, which is in very close agreement with the specified goal of design.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.4
• /
• pp.297-301
• /
• 2000

Planar optical waveguides which have a higher refractive index than that of substrate were fabricated by proton exchange between $Li^+$ and $H^+$. Benzoic acid was used as proton source and process was carried out under the various reaction time and temperature. The depth of waveguide layer and the generated mode number were investigated by standard prism coupler. The cut-off depth for the fabrication of single mode optical waveguides was obtained by the function which was expressed on refractive index profile. Finally the experimental conditions for cut-of depth of single mode could be confirmed. Channel waveguides were manufactured from these confirmed conditions and the effective confinement of the induced light into waveguides was observed.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.12
• /
• pp.607-613
• /
• 2001

Molybdenum thin films were deposited on the soda lime glass(SLG) substrates by direct-current planar magnetron sputtering, with a sputtering power density of $4.44W/cm^2$. The working pressure was varied from 0.5 mtorr to 20 mtorr to gain a better understanding of the effect of sputtering pressure on the morphology and microstructure of the Mo film. Thin films of $CU(InGa)Se_2$ (CIGS) were deposited on the Mo-coated glass by three stage co-evaporation process. The highest efficiency device was obtained at the maximum value of the tensive stress. The morphology of Mo-coated films were examined by using scanning electron microscopy The film's microstructure, such as the preferred orientation, the full width at half-maximum(FWHM), and the residual intrinsic stress were examined by X-ray diffraction.