• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.6
• /
• pp.53-58
• /
• 2004

A novel UV sensor was manufactured and characterized using evanescent field coupling between photochromic dye dispersed polymer waveguide and side polished fiber. The spiroxazine (photochromic dye) dispersed polymer was used as planar waveguides. The resonant wavelength was shifted owing to refractive index variation of planar waveguide on exposed UV because of its photo-functional properties. The sensitivities are $1.21{\mu}W/mw$ and $2.75{\mu}W/mw$ when UV intensities increased after exposure times were fixed at 3 seconds and 5 seconds, respectively. Output optical power according to UV intensity increases and saturation time decreases as the intensity of UV radiations increases.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.3
• /
• pp.140-149
• /
• 2002

This paper describes the characteristics of beam-tilting slot away waveguide antennas for mobile DBS reception. As a basic study of slotted waveguide array, design for 16 slot elements located on a broad-wall waveguide is considered. Design parameters such as slot length, space between each slot and cross slot angle of antennas with the beam-tilting characteristics are calculated by method of moments. Based on these results, the radiation waveguide antennas with 16-element $\times$16-array are designed and fabricated. The measured main beam direction angles of the fabricated antennas are 48$^{\circ}$to 50$^{\circ}$depending on the measured frequencies and it shows good agreement with prediction. The measured 3 dB beam width of elevation pattern is about 13$^{\circ}$, and the axial ratio and the gain measured at DBS band are observed 2.8 dB below and 24 dBi above, respectively. In order to evaluate a performance of the fabricated waveguide planar antenna, it is combined with the satellite tracking control system and the field performance test of antenna mounted on a mobile vehicle is carried out at highway. During the measurement, it was possible to watch television without a break signal in a driving vehicle and an excellent performance of the proposed antennas was demonstrated.

• Korean Journal of Optics and Photonics
• /
• v.15 no.6
• /
• pp.490-494
• /
• 2004

Bragg gratings were fabricated in Ge-doped silica planar lightwave circuits (PLC) for different writing conditions to study the growth characteristics. The refractive index modulation of the gratings grew in the PLC with total fluence F according to the power law $\Delta$n=A $F^{B}$. The characteristics of the PLC gratings formed for external cavity lasers match closely to those predicted by the power law. The oscillation spectra of the FP-LD with a Bragg grating grown in the PLC waveguide were also presented.d.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.9
• /
• pp.60-66
• /
• 2008

In this paper, the CPW-fed Ultra-wideband antenna is designed and fabricated for UWB communications. To achieve ultra-wide bandwidth of the antenna, we propose the mutual coupling of two planar monopole antennas. The mutual coupling of monopole pair of the proposed antenna is optimized by adjusting the parameters, the widths of the planar monopoles and the space between two monopoles. Two UWB antennas with different horizontal sections of the CPW-fed monopole antenna are fabricated and measured to examine the mutual coupling effects on the monopole pair antenna. The measured result show that two antennas are satisfied with UWB communication band(3.1$\sim$10.6Ghz).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.5
• /
• pp.444-449
• /
• 2003

In this paper, a PCB(Printed Circuit Board) antenna for IMT-2000 is designed and analyzed. The antenna has a helical structure with via-holes and lines on FR-4($\varepsilon$$\sub$${\gamma}$/=4.6 ) PCB, and the type of feeding is GCPW(Grounded Co-Planar Waveguide). Using HFSS of Ansoft, the antenna was designed and the measured results of frequency and radiation characteristic,3 with VSWR<2.0 are satisfied within operating frequency band of 1.920∼2.170 GHz. And it has resonating frequency of 2.045 GHz and a bandwidth of 321 MHz. The radiation gain of the antenna was measured to be -1 dBi.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.9
• /
• pp.52-59
• /
• 2009

In this paper, the planar waveguide slotted array antenna is presented, which has the 3-layered structure of feeding networks for a high gain. Due to the ionosphere which generates 'Faraday rotation', the skew is happened between the signal radiated from an artificial satellite and the receiving antenna. This causes a polarization loss. In this paper, to remove this polarization loss, the dumbbell shaped linear polarizer using a single layer film is proposed. The gain of proposed antenna is 29.4dB.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.1125-1128
• /
• 2003

This paper presents the design method of a Colpitts type oscillator with coplanar waveguide(CPW) structures in the range of Ka-band frequency for transmitter and receiver modules. Series short stubs of CPW patterns provide inductances and capacitances in the range of Ka-band which can be expressed as a CLC-$\pi$ equivalent circuit. The experimentation has employed ro4003 substrates as a CPW substrate which has a dielectric constant of 3.38 and a signal and ground space of 100um. A method of momentum simulation for the CPW patterns has performed with an ADS software tool of Hewlett-Packard Corp. Inductance and capacitance circuits of a Colpitts oscillator was interconnected to a MESFET with CPW bend structures of including the input and output impedance matching circuits of the active transistor. Circuit parameters for impedance matching were determined through the network conversion to the equivalent length of CPW transmission lines by using T-network 1 $\pi$-network conversion circuit. A Colpitts oscillator was fabricated on the substrate of a area of 8.5mm x 17.4mm with a MESFET of Fujitsu FMM5704X and CPW series short stubs. The design suggested the possibility of realizing oscillators on a planar surface for the wireless system of tansmitter and receiver modules in the frequency range of 30GHz

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.1
• /
• pp.90-98
• /
• 1999

This paper presents a wideband single-balanced mixer using a diode which can be used in RF receiver of microwave measurement systems. For wideband characteristic, local oscillator(LO) signal is provided to diode with low loss using a coplanar waveguide-to-slotline balun. For high isolation characteristic radio frequency (RF) port and intermediate frequency (IF) port are designed using directional coupler. This mixer presents 30.5~31.17dB conversion loss whose flatness is within 1dB for 9 kHz~2.6 GHz wideband RF signal, and above 30 dB isolation for LO signal.

• Korean Journal of Optics and Photonics
• /
• v.21 no.1
• /
• pp.1-5
• /
• 2010

In this study, we propose a grating structure using guided-mode resonance (GMR) to increase the absorption efficiency of a silicon solar cell. The proposed solar cell design consists of a one-dimensional diffraction grating and a planar waveguide layer of poly-silicon deposited on a silver reflector. We investigate the influence of structure parameters such as grating period, waveguide thickness, grating width and grating depth. Optimal parameters are found using the particle swarm optimization (PSO) algorithm. In the optimized GMR-assisted solar cell, absorption efficiency up to 65.8% is achieved in the wavelength range of 300 nm~750 nm.

• Journal of information and communication convergence engineering
• /
• v.14 no.4
• /
• pp.252-257
• /
• 2016

An edge-located electromagnetic bandgap (EL-EBG) structure using a defected ground structure (DGS) is proposed to suppress resonant modes induced by edge excitation in a two-dimensional planar parallel plate waveguide (PPW). The proposed EL-DGS-EBG PPW significantly mitigates multiple transverse-magnetic (TM) modes in a wideband frequency range corresponding to an EBG stopband. To verify the wideband suppression, test vehicles of a conventional PPW, a PPW with a mushroom-type EBG structure, and an EL-DGS-EBG PPW are fabricated using a commercial process involving printed circuit boards (PCBs). Measurements of the input impedances show that multiple resonant modes of the previous PPWs are significantly excited through an input port located at a PPW edge. In contrast, resonant modes in the EL-DGS-EBG PPW are substantially suppressed over the frequency range of 0.5 GHz to 2 GHz. In addition, we have experimentally demonstrated that the EL-DGS-EBG PPW reduces the radiated emission from -24 dB to -44 dB as compared to the conventional PPW.