• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.8
• /
• pp.1591-1598
• /
• 2002

This paper reports on the effects of crankshaft offset on the engine friction. The effects of crank offset are investigated through the theoretical analysis. In this study, the mathematical models are presented fer evaluationg the friction level of each engine parts. Crank offset influences on the side force acted on the piston pin and sliding speed of piston. Crank offset is very effective to reduce the piston skirt friction. With application of crank offset, total engine friction decreases at low engine speed, but that increase as engine speed increases.

• Journal of the Korean Society of Safety
• /
• v.2 no.1
• /
• pp.59-71
• /
• 1987

A study has been made of the damping force phenomena of the shockabsorber for automobile. The main results obtained are as follows; 1) We can neglect friction loss between cylinder and piston, as it is very small compared to other damping force. 2) Damping force due to coil spring and disc valve shows comparatively stable at various piston speed and oil temperature. 3) Theoretical and experimental values are well agreed on relatively low piston speed. 4) Theoretical value on piston speed of 600mm/sec, 900mm/sec at oil temperature $20^{\circ}C$, $40^{\circ}C$, $60^{\circ}C$ and $80^{\circ}C$ is about 82% of experimental value. 5) Theretical value at oil temperature $-20^{\circ}C$, $0^{\circ}C$ is about 67% of experimental value.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.5
• /
• pp.70-76
• /
• 2007

The purpose of this study is to analyze the characteristics of a domestic developed hydraulic axial piston motor. An experimental apparatus was constructed and the output torque, the input oil pressure, the input flow rate, the speed of motor and oil temperature were measured. They were measured under both no load and load conditions. The results are as follows; 1. Motion of motor became steady state conditions after 5 seconds. 2. Output torque of motor was proportional to input oil pressure under both load and unload. 3. Speed of motor decreased with increasing load. 4. Oil temperature was almost constant. The results of this study will offer the basic data in designing and operating hydraulic axial piston motors.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.1
• /
• pp.41-49
• /
• 1993

Piston slap is one of the major sources of noise in a 4-cycle diesel engine. Piston slap is not only one of major source mounted near the top and bottom of the piston thrust and antithrust skirts. Effects of engine speed, load and coolant temperature on piston motion were investigated. The measured piston motion showed 6 slapes per cycle resulting from the change of side force. Major piston slap timing was retarded as engine speeds became higher. The increase of engine load made large piston transverse movement toward thrust side of cylinder block. Piston transverse movement was due to reduced piston-liner clearance at higher coolant temperature.

• Tribology and Lubricants
• /
• v.17 no.6
• /
• pp.435-440
• /
• 2001

A numerical analysis between the piston and cylinder in hydraulic piston pumps under reciprocating motion is presented. A finite difference method and the Newton-Raphson method are used simultaneously to solve the Reynolds equation in the clearance and the equation of motion for the piston. The tapered piston showed stable behaviors regardless of their initial eccentric positions in the clearance, and the reciprocating speed affect highly on the piston end trajectories. Therefore, the numerical methods and results of present study can be used in the lubrication study of other piston-cylinder type fluid machineries.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.3
• /
• pp.95-103
• /
• 2010

This paper presents a simulation model of a double-acting high-speed pneumatic cylinder with a relief valve type cushion mechanism. The model predicts piston motion, mass flow rate, pressure and temperature time histories of cushion chamber. Of interest here is to investigate the cushioning effect of varying the piston and piston-rod diameter, cushion ring diameter and length, and stoke in cushion mechanism. As a result, this cushion mechanism is found to be adequate under high-speed driving of pneumatic cylinders. The simulation model proposed here will be very useful to analyze the dynamic characteristics and to improve or design the better cushion mechanism in high-speed pneumatic cushion cylinders.

• Journal of the Korean Society of Industry Convergence
• /
• v.22 no.5
• /
• pp.511-517
• /
• 2019

Two type pistons which had different configuration were made to find out the effects on combustion and flame propagation. Flame propagation speed was obtained by use of the cylinder head gasket ionization probe. Ionization Probe voltage output and flame propagation speed were increased according to the air fuel mixture ratio increase. Exhaust direction flame propagation speed was fastest in combustion chamber and next was front direction, rear direction and intake direction cause of tumbling motion in cylinder. In case of remove the valve pocket in piston, average flame propagation speed changed slowly and spark timing was advanced. Also emission was decreased.

• Journal of Mechanical Science and Technology
• /
• v.15 no.5
• /
• pp.562-568
• /
• 2001

The rolling piston type-rotary compressor has been widely used for refrigeration and air-conditioning systems due to its compactness and high-speed operation. The present analysis is part of a research program directed toward maximizing the advantages of refrigerant compressors. The study of lubrication characteristics in critical sliding components is essential for the design of refrigerant compressors. Therefore, theoretical investigation of the lubrication characteristics of a rotary compressor used for refrigeration and air-conditioning systems was studied. The Newton-Raphson method was used for the partial elastohydrodynamic lubrication analysis between the vane and the rolling piston of a rotary compressor. The results showed that the rotational speed of a shaft and the discharge pressure significantly influence the friction force and the energy loss between the vane and the rolling piston.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.6
• /
• pp.1510-1519
• /
• 1994

It is important to understand the friction characteristics between piston-ring assembly and cylinder wall for the friction loss reduction as well as the solution of problem such as scuffing wear and oil consumption. A new system was developed for the piston-ring assembly friction force measurement. This system was applied to the friction force measurement to find its functional relationship with variables such as engine speed, oil viscosity, and engine load. The friction mean effective pressure(fmep) was found to have a linear relationship with$(\vpsilon{U})^{0.42}$ under motering and with$(\vpsilon{U})^{0.45}$ under firing operations, where $\vpsilon$ is the kinematic oil viscosity and U is mean piston speed.

• KSTLE International Journal
• /
• v.9 no.1_2
• /
• pp.17-21
• /
• 2008

The rolling piston type rotary compressor has been widely used for refrigeration and air-conditioning systems due to its compactness and high-speed operation. The present study is one of studies to maximize the advantages of refrigerant compressors. In addition, because friction characteristics of the critical sliding component is essential in the design of refrigerant compressors, the present study also analyzed the lubrication characteristics of a rotary compressor used for refrigeration and air-conditioning systems. In order to measure the friction force between the vane and the rolling piston, an experimental apparatus known as the Pin-on-Disk was used. Load is applied by the hydraulic servo valve controlling the pressure of the hydraulic cylinder. The results showed that the rotational speed of the shaft, the operating temperature, and the discharge pressure significantly influenced the friction force between the vane and the rolling piston.