• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.3
• /
• pp.103-111
• /
• 2006

The spray behavior of direct-injection spark-ignition(DISI) engines is crucial for obtaining the required mixture distribution for optimal engine combustion. The spray characteristics of DISI engines are affected by many factors such as piston bowl shape, air flow, ambient temperature, injection pressure and fuel temperature. In this study, the effect of fuel temperature on the spray and combustion characteristics was partially investigated for the wall-guided system. The effect of fuel temperature on the fan spray characteristics was investigated in a steady flow rig embodied in a wind tunnel. The shadowgraphy and direct imaging methods were employed to visualize the spray development at different fuel temperatures. The microscopic characteristics of spray were investigated by the particle size measurements using a phase Doppler anemometry(PDA). The effect of injector temperature on the engine combustion characteristics during cold start and warming-up operating conditions was also investigated. Optical single cylinder DISI engine was used for the test, and the successive flame images captured by high speed camera, engine-out emissions and performance data have been analyzed. This could give the way of forming the stable mixture near the spark plug to achieve the stable combustion of DISI engine.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.889-891
• /
• 2017

Usually piston or rotary engines are installed at UAV's under 100 kg payload class. Those engine are less expensive and easy to get, but they require higher operating and maintenance costs due to shorter life and unique fuel usage. They are also too noisy to operate in urban area and have too strong vibration to carry sophisticated payloads. On the contrary, a gas turbine engine has drawbacks like higher specific fuel consumption and weight to power ratio, even it has many operating and maintenance benefits. This study aims to design a small turboshaft engine with a recuperator to overcome those demerits. A tilt rotor UAV(TR-60) developed by KARI was chosen as an imaginary target aircraft, and engine power and size were derived from it. This paper describes engine requirements, design process, and initial reference point cycle design.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1991.06a
• /
• pp.55-59
• /
• 1991

실중적으로 하중을 받는 선접촉부의 윤활명성은 johnson chart, 또는 Hooke의 Chart에서 나타난바와 같이 강체$\cdot$점도일정명감 (Rigid-Isovicosity region), 점도변화 명성 (Elasticity-Variable Viscosity Region), 탄성체$\cdot$점도일정명성 (Elasticity-Isoviscosity Region)으로 분산 되어지는데 명성내에서 2차원 선접촉의 경우 탄성 파라메터 ge가 적고 점성 파라미터 gv가 큰 Tribology적인 실제 문제가 많은데 비하여 이 점성에서의 윤활특성에 관한 수치적인 Simulation이나 실험적인 보고가 거의 없는 실정이다. 예를들면 engine의 Piston Ring과 Cylinder 간의 윤활, Vane 식의 유압펌프등에서 볼수 있는 습동부의 윤활, Rotary Engine의 Rotor 선단부분, Rotary Compressor의 Rotor와 stator간의 상대운동 점성에서 나타나는 Tribology적인 점성은 대부분이 강체$\cdot$점도 변화점성이거나 그에 바로 인접한 탄생체$\cdot$점도 변화의 초기 점성에 분포하고 있다.

• Journal of the Korean Society of Visualization
• /
• v.9 no.4
• /
• pp.16-21
• /
• 2011

The effects of stroke change on turbulent kinetic energy for the in-cylinder flow of a four-valve SI engine were studied. For this study, the same intake manifold, head, cylinder, and the piston were used to examine turbulence characteristics in two different strokes. In-cylinder flow measurements were conducted using three dimensional LDV system. The measurement method, which simultaneously collects 3-D velocity data, allowed a evaluation of turbulent kinetic energy inside a cylinder. High levels of turbulent kinetic energy were found in regions of high shear flow, attributed to the collisions of intake flows. These specific results support the more general conclusion that the inlet conditions play the dominant role in the generation of the turbulence fields during the intake stroke. However, in the absence of two counter rotating vortices, this intake generated turbulent kinetic energy continues to decrease but at a much faster rate.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.8
• /
• pp.1101-1110
• /
• 1998

Computational investigation was conducted to examine the performance of a high pressure common-rail fuel injection system which is used to power a passenger car direct injection (Dl) diesel engine. The pipe flows were modeled by one dimensional wave equation and solved by implicit FDM Each volume of injector was considered as chambers with orifice nozzle in connections. These simulation results were compared with the experimental data of Ganser Hydromag. The comparison of needle life and rate of injection between simulation data and experimental data showed quite a good agreement Different shape of injection rate can be made by adjusting the size of inlet orifice and exit orifice in the piston chamber The pilot injection was accomplished by adjusting command signal.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.9
• /
• pp.722-727
• /
• 2009

The effect of the intake flow on the spray structure of a high pressure 11-hole fuel injector were examined in a single cylinder optical direct injection spark ignition (DISI) engine. The effects of injection timing and in-cylinder charge motion were investigated using the 2-dimensional Mie scattering technique. It was confirmed that in the homogeneous charge mode, the in-cylinder swirl charge motion played a major role in the fuel spray distribution during the induction stroke rather than the tumble flow. But, in the stratified charge mode, the effect of the in-cylinder charge was not so large that the injected spray pattern was nearly maintained and the increase of in-cylinder pressure by the upward moving piston reduced the fuel spray penetration.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.5
• /
• pp.114-122
• /
• 1997

Nowadays, gasoline direct injection engines are being commercialized by virtue of improvement in control technology of spray, flow, air fuel ratio. The stratified charge type has the advantage of improving lean limit. The homogeneous type has the advantage of reducing engine-out hydrocabon emissions in the first 30 seconds after a cold start, in addition, improving transient air fuel ratio control. The vaporization and mixing if injected fuel with air has to e completed in a short time and the fuel film in cylinder and on piston has to be minimized. So, the flow and injection should be well controlled. This paper surveyed the spray characteristics of gasoline direct injection by using laser equipment and the combustion characteristics of the single cylinder engine using homogeneousas-mixture type gasoline direct injection.

• Journal of computational fluids engineering
• /
• v.5 no.3
• /
• pp.1-7
• /
• 2000

In high-pressure diesel engine, the injected fuel spray impinges on the piston cavity surface due to the short distance between the injection nozzle and the cavity wall. The behavior of the impinging spray has the great influence on the dispersion of fuel, the evaporation, and the mixture formation process. In this study, the numerical simulation using the GTT code was performed to study the gas flows, the spray behaviors, and the fuel vapor distributions in the combustion of a D.I engine for variation of spray angle and swirl ratio.

• Journal of the Korean Society of Combustion
• /
• v.11 no.4
• /
• pp.1-8
• /
• 2006

The model cavity scramjet engine experiments are carried out using T3 free-piston shock tunnel. Upstream hydrogen fuel is injected before the cavity with different injection pressure. OH planar laser-induced fluorescence is used to investigate the combustion zone and piezoelectric pressure transducers are used to define the pressure rise due to the combustion. Main combustion region is a mixing layer which is between air and fuel. Also high OH fluorescence signal is appeared in the shear layer above the cavity in high equivalence ratio. From the OH signal in the cavity, this fuel injection system can be a role as a flame-holder.

• 한국연소학회:학술대회논문집
• /
• 2000.12a
• /
• pp.183-193
• /
• 2000

Soot formation and oxidation is closely related to the combustion phenomena inside a diesel engine. Laser-based diagnostics provide a means for improving our understanding of diesel combustion, because they have highly temporal and spatial ability. To understand the soot behavior we did preliminary study by taking flame luminosity photographs and 2-D images of soot distribution using Laser Elastic Scattering(LIS) and Laser-Induced Incandescence(LII). From the data we found that soot concentration was high in the bowl and disappeared from the central region in the late combustion stage and that soot exists in the flame using luminosity, LIS and LII.