• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권5호
• /
• pp.309-317
• /
• 2004

This paper suggested the vibration characteristic improvement by variation mode of ring type ultrasonic motor. Design for the piezoelectric ceramic and elastic body of stator were calculated by the finite element method(FEM) that consider the resonance frequency, vibration mode and coupling efficiency etc. Through the result of vibration analysis from 6 order mode to 8 mode, the 7 order mode was gained very an excellent results that it was the coupling efficient, minimum power loss and bending vibration value. Here over 7 order mode, this paper was acquired that an output current for input voltage was very a large increased results. The result of vibration calculation, from thickness 0.5[mm] to 2[mm], knew the fact that the vibration displacement at 0.5[mm] is an high value too. From such result, this paper was manufactured the ultrasonic motor of outer diameter 5O[mm] , inter 22[mm] having the about 43.86[KHz] resonance frequency. We have gated that a simulation result is 42.2[KHz] and an experiment result is 43.86[KHzl The propriety of this paper was established though comparison. investigation of simulation and experiment result.

• 한국전기전자재료학회논문지
• /
• 제16권6호
• /
• pp.484-489
• /
• 2003

In this paper, a single phase driven piezoelectric motor design was presented for linear motion Two metal/ceramic composite actuators, a piezoelectric ring which was bonded to a metal endcap from one side, were used as the active elements of this motor. The motor was composed of a piezoelectric ceramic, a metal ring which has 4 arms, and a guider. Motors with 30 [mm] and 35 [mm] diameter were studied by finite element analysis and experiments. As results, the maximum speed of motor was obtained at resonance frequency. When the applied voltage of the motor increased, the speed was increased. Also, bidirectional motion of the motor was achieved by combining two motors which have different resonance frequency. But the characteristics of bidirectional motion were not equaled, because of the problem of reproduction on the fabrication and the experiment. If present motor is used at the auto-zoom device of a camera, it will have much advantage. Because the direct linear motion can be achieved with a simple structure of motor and no gearbox of total system.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 춘계학술대회 논문집
• /
• pp.29-32
• /
• 1998

A plate-type ultrasonic linear motor using longitudinal and bending multi-vibration mode was designed and fabricated for card-forwarding device. The rotor consisted of piezoelectric ceramic plate and elastic materials. The performances of the motor were measured. As the experimental results, no-load speed of the motor was 0.6 m/s at 80 V in applied voltage. Starting torque was 1.4 mNm and maximum efficiency was 1.2 %.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.741-743
• /
• 2000

In this paper the relationship between the pressing force applied to rotors and the characteristics of ultrasonic motor are discussed. The characteristics of ultrasonic motor using a piezoelectric vibrator were systematically studied. And these were applied to the construction of a card forwarding device. The principle of ultrasonic motor is to use an elliptical motion generated on the side of the vibrator, and the elliptical motion of the ultrasonic motor was obtained by complex oscillation of $L_1-B_4$ mode. As the experimental results. the forwarding speed of the card increased linearly as the pressing force applied to rotors increased. The forwarding speed of the card was 16.0 cm/s when the pressing force applied to rotors was 1 N. The forwarding force of the card increased linearly as the pressing force applied to rotors increased. The forwarding force of the card was 398 mN when the pressing force applied to rotors was 1 N. Therefore, this ultrasonic motor can be expected to be used for card-forwarding device and so on.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.304-307
• /
• 2003

In this paper, stacked piezoelectric ceramics were used for obtaining a large vibration for a small ultrasonic motor which is useable for the both linear drive and rotational drive. We studied this motor through the finite element analysis method and the simulated driving characteristics were presented. As results, the displacement of the tip of the stator was increased when the layers of the ceramics were increased. Also, by inserting additional aluminum plates between the ceramics and the aluminum bar, the displacement were amplified. In this model, two voltages which have 90 degree phase difference were applied for the bi-directional movement.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.187-188
• /
• 2008

An ultrasonic motor of high torque with a new configuration for application in automobiles is proposed. The newly designed stator is a two sided vibrator consisting of a toothed metal disk with a piezoelectric ceramic ring bonded on both faces of the disk which generates a flexural traveling wave along the circumference of disk. In this configuration, the displacement on the surface of stator may not be confined. It also produces a large vibrating force and amplitude because the vibrator is sandwiched by two piezoelectric plates. It is possible to increase the torque by improving the vibration characteristics. To compute the vibration mode of the motor of diameter 48 mm, the finite element method was used. A 6th mode was chosen as the operation mode with a resonance frequency of about 64.4 kHz. According to this design and measured its performance, a prototype was fabricated. The performance measurement of the prototype motor showed that its stall torque was about 1.8 Nm and efficiency was 37% at 60% of the maximum torque.

• 한국전기전자재료학회논문지
• /
• 제18권10호
• /
• pp.891-895
• /
• 2005

Novel structure ultrasonic motors which have cross type stator were designed and fabricated. Driving characteristics of the motors were analyzed and measured by changing the materials of the stator. This ultrasonic motor has stator with hollowed cross bar and the stator rotate the rotor using elliptical displacement of the inside tips. This motion is generated by lateral vibration mode of cross bars. This stator was analyzed by finite element analysis depandent on stator's materials. And the cross type ultrasonic motors were made by analyzed results. The larger displacements were obtained, when the density of material was decreased. But the stress was increased when the stator's material has large density and Young's modulus. The fabricated one has high speed and torque in large stress on contact point between rotor and stator. The stress was more effected on speed and torque than the displacement.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.354-356
• /
• 2005

Novel structure ultrasonic motors which have cross type stator were designed and fabricated. Driving characteristics of the motors were analyzed and measured by changing the materials of the stator. This ultrasonic motor has stator with hollowed cross bar and the stator rotate the rotor using elliptical displacement of the inside tips. This motion is generated by lateral vibration mode of cross bars. This stator was analyzed by finite element analysis and the ultrasonic motors were made by analyzed results. The larger displacements were obtained, when the Young's modulus was increased and the Poisson's ratio was decreased. The fabricated one has high speed in large Poisson's ratio and Young's modulus. And the torque was increased in high Young's modulus.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 학술대회 논문집 정보 및 제어부문
• /
• pp.754-756
• /
• 2004

The ultrasonic piezo motor is a new type motor that has an excellent performance and many useful features that electromagnetic motors do not have. But, it suffers from severe system non-linearities and parameter variations especially during speed control. Therefore, it is difficult to accomplish satisfactory control performance by using the conventional PID controller. In this paper, to achieve the precise control, we analyzed response time & change with a driving time, and proposed PD controller combined with neural network. The backpropagation algorithm is used to train a given trajectory. The effectiveness of the used method is confirmed by experiments. The effectiveness of the used method is confirmed by experiments using the ultrasonic motor made in Korea.

• 한국음향학회지
• /
• 제15권1호
• /
• pp.10-16
• /
• 1996

압전초음파모터는 기존의 전자기식모터와는 달리 압전전체가 발생하는 초음파진동에 의한 마찰력으로 회전자의 구동력을 얻는 모터이다. 이는 구조가 간단하고, 저속에서 높은 토오크를 얻을 수 있어 감속기구 없이 직접구동이 가능한 장점이 있어 주목을 받고 있다. 그러나 이 모터는 인가주파수, 인가전압, 2상의 구동신호사이의 위상차 및 구동신호의 duty비 등에 따라 그 특성이 변하므로, 모터를 제어하기 위해서는 이러한 변수들에 대해 정밀한 특성측정이 필요하다. 본 연구에서는 초음파모터의 제작과 함께 컴퓨터인터페이스된 압전초음파모터 평가장치를 개발하였고, 제작한 초음파모터의 특성을 여러 구동변수에 대해 측정하였다. 구동변수들은 모두 디지털로 처리되므로, 초음파모터의 특성측정을 쉽게 할 수 있을 뿐만 아니라, 차후 초음파모터의 디지털제어에 기본 바탕이 된다.