• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.341-344
• /
• 1989

A Modified equivalent circuit by combining a series and parallel of polymer matrix for estimating the dielectric constant ${\bar{K}}_{33}$ values changing the volume percent of $PbTiO_3$, the dependences of frequency for the 713 and dissipation factor for 0 - 3 composites was derived. The difference of the dielectric constant and dissipation factor between the calculated and measured values became smaller at higher volume percent of $PbTiO_3$. There was, good agreement between the calculated and observed results for 70 volume percent of $PbTiO_3$ and 30 volume percent of Eccogel composite at 1(KHz), 25($^{\circ}C$). The optimized variable x was 0.94 in $PbTiO_3$ ceramics. $PbTiO_3$ powder and Eccogel polymer were used as piezoelectric fillers and matrix, respectively.

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.79-80
• /
• 2006

In this paper, ultrasonic nozzle and driving circuit were manufactured and their electrical properties were investigated. Uitrasonic nozzle was fabricated using PSN-PMN-PZT ceramics showing excellent piezoelectric characteristics. In order to drive ultrasonic nozzle, PWM controller(KA3525A) was used. With increasing input voltage of nozzle, particle diameters of diesel were increased up tot 16V and then decreased. At the input voltage of 12V, volume particle diameter showed the minimum value of $37.3{\mu}m$ and also at the input voltage of 18V, volume particle diameter showed the maximum value of $51.3{\mu}m$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.272-273
• /
• 2007

In this paper, ultrasonic nozzle and driving circuit were manufactured, respectively. And then, their electrical properties. were investigated. Ultrasonic nozzle was fabricated using PSN-PMN-PZT ceramics showing excellent piezoelectric characteristics. In order to drive ultrasonic nozzle, PWM controller(KA3525A) was used. The purpose of this study is to find the optimal driving condition of ultrasonic. nozzle. Accordingly electrical and temperature characteristic of ultrasonic driving system were investigated as a function of the input voltage.

• Journal of Sensor Science and Technology
• /
• v.13 no.6
• /
• pp.417-423
• /
• 2004

In order to obtain wide-beam characteristics and variable resonant frequency of a ultrasonic transducer for the array source, an electrode of transverse mode piezoelectric vibrator is divided, and an electronic inductance is connected to the divided electrodes. The electronic inductance is made by GIC (General Impedance Converter) circuit. Because the GIC circuit is made of OP-Amps and other passive elements, the value of the inductance can be selected easily. As the results, the electronic inductance is variable in the range from 0.2 mH to 1.2 mH. Using the inductance, the resonance frequency of the transducer can be changed in the range from 73 kHz to 86 kHz. In the directivity of the transducer, it is confirmed that the beam width of the transducer is wider than $80^{\circ}$ at -3 dB in water.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.6
• /
• pp.239-244
• /
• 2015

Lead zirconate titanate (PZT) thick films with thickness of $10{\sim}20{\mu}m$ were fabricated on silicon substrate by aerosol deposition method. As-deposited films on silicon were annealed at the temperatures of $700^{\circ}C$. The electrical properties of films deposited by PZT powders were characterized using impedance analyzer and Sawyer-Tower circuit. The PZT powder was prepared by both conventional solid reaction process and sol-gel process. The remanent polarization, coercive field, and dielectric constant of the $10{\mu}m$ thick film with solid reaction process were $20{\mu}C/cm^2$, 30 kV/cm and 1320, respectively. On the other hand, the PZT films by sol-gel process showed a poor dielectric constant of 635. The reason was probably due to the presence of pores produced from organic residue during annealing.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.4A
• /
• pp.587-596
• /
• 2006

A half portion of Korean railway bridges depends on the type of steel plate girder bridge. Since these bridges have been built in the early stage of Korean economical boom, numerous maintenance effort suffers from aging and progressive degradation issues at present. In accordance with these efforts, this paper would like to address the detailed analyses of thin steel plates with bolts in order to simulate the connection regions of steel plate girder bridge. The fundamental modal analysis, transient dynamic analysis with 3D piezoelectric element in open circuit loop and signal process with aids of TOF(time of flight) and WC(wavelet coefficient) are extensively discussed.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.2
• /
• pp.115-122
• /
• 2008

Mostly used sensors have wired powering and two-way cable systems. It is difficult to employ wired sensor network in ubiquitous era because of a number of sensors and cables. Therefore, sensor networks move from wired systems to wireless systems for the future. However, the power source is a critical obstacle for wireless sensornodes. This research represents the new power source which supplies energy sensor node, maintains over 10 years, and thus replaces batteries with limit of lifetime. The system with piezo materials scavenges extra energies such as vibration and acceleration from the environment. Then it converts the scavenged mechanical energy to electrical energy for powering a sensor, a controller and a circuit for regulating voltage and transmitting sensor value. This study explains the properties of piezo material through theoretical analysis and experiments, and demonstrates powering sensor and transmitting data with stored energy (35mJ) for 14 sec. The developed system provides a solution to overcome the critical problem of making up wireless sensor networks.

• The Journal of the Acoustical Society of Korea
• /
• v.21 no.7
• /
• pp.592-599
• /
• 2002

In this study, an ultrasonic transducer was designed with a commercial finite element analysis (FEA) code, PZFlex, and fabricated based on the design. The transducer has the dimension and shape suitable for abdomen diagnosis working at 5 ㎒ and consists of 128 piezoelectric elements disposed in a convex linear array form. The transducer is composed of two impedance matching layers, one backing layer, and kerfs placed between the piezoelectric elements. Validity of the design with the FEA was illustrated through experimental characterization of a sample transducer. Comparison with the design results by equivalent circuit analysis method was also made to check the superiority of the FEA design.

• Journal of Magnetics
• /
• v.16 no.2
• /
• pp.157-160
• /
• 2011

The magnetostrictive material is magnetized in magnetic field and produces a nonuniform demagnetizing field inside and outside it. The demagnetization is decided by the permeability of magnetostrictive material and its size. The magnetoelectric performances are determined by the synthesis of the applied and demagnetizing fields. An analytical model is proposed to predict the magnetoelectric voltage coefficient (MEVC) of magnetostrictive/piezoelectric laminate composite using equivalent circuit method, in which the nonuniform demagnetizing field is taken into account. The theoretical and experimental results indicate that the MEVC is positively connected with the permeability and the piezomagnetic coefficient of magnetostrictive material. To obtain the maximum MEVC, both the permeability and the piezomagnetic coefficient of magnetostrictive material should be taken into account in selecting the suitable magnetostrictive material.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.8
• /
• pp.983-989
• /
• 2013

This study proposes a piezoelectric vibration energy harvester composed of two diagonally segmented energy harvesting units. An auxiliary structural unit is attached to the tip of a host structural unit cantilevered to a vibrating base, where the two components have beam axes in opposite directions from each other and matched short-circuit resonant frequencies. Contrary to the usual observations in two resonant frequency-matched structures, the proposed structure shows little eigenfrequency separation and yields a mode sequence change between the first two modes. These lead to maximum power generation around a specific frequency. By using commercial finite element software, it is shown that the magnitude of the output power from the proposed vibration energy harvester can be substantially improved in comparison with those from conventional cantilevered energy harvesters with the same footprint area and magnitude of a tip mass.