• 한국정밀공학회지
• /
• 제30권12호
• /
• pp.1281-1286
• /
• 2013

In this paper, a miniaturized stage with two prismatic-prismatic joints (2-PP) type parallel compliant mechanism driven by piezo actuators is proposed. This stage consists of two layers which are a motion guide layer and an actuation layer. The motion guide layer has 2-PP type parallel compliant mechanism to guide two translational motions, whereas the actuation layer has two leverage type amplification mechanisms and two piezo actuators to generate forces. Since the volume of the stage is too small to mount displacement sensors, the piezo actuators embedding strain gauge sensors are chosen. With the strain gauge-embedded piezo actuators, a semi-control is implemented, which results in hysteresis compensation of the stage. As the results, the operating range of $30{\mu}m$, the resolution of 20 nm, and the bandwidth of 400 Hz in each axis were obtained in the experiments.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.72-77
• /
• 2007

A pressure sensor is a sensing device to perceive inputing pressure and convert pressure with an electric signal. Currently, a domestic pressure sensor mostly uses mechanical methods. So, it uses many parts and its cost is high. Therefore, It is necessary to improve the weak points of an existing pressure sensor and develop the accurate and reliable pressure sensor using piezo resistance strain gages.

• 한국항공우주학회지
• /
• 제32권3호
• /
• pp.37-44
• /
• 2004

본 논문에서는 압전재의 재료 비선형성을 고려한 경량 압전 복합재 작동기(LIPCA)의 성능 해석을 수행하였다. 성능 해석을 위해 9절점 쉘 요소 정식화에 바탕을 둔 압전 쉘 요소를 이용하였다. LIPCA의 작동 변위를 보다 정확히 예측하기 위하여, 실험을 통해 얻은 압전 변형률 함수와 증분 정식화를 추가하여 기존 선형 유한요소 프로그램을 수정하였다. 이렇게 개발된 재료 비선형 압전 옐 프로그램을 이용하여 LIPCA의 작동변위를 재 계산하였고, 재료 비선형 해석으로 얻은 작동 변위가 선형 해석으로 계산된 작동 변위 보다 측정 변위에 훨씬 근접함을 확인하였다.

• Structural Engineering and Mechanics
• /
• 제56권4호
• /
• pp.649-665
• /
• 2015

The present paper attempts to investigate the propagation of plane waves in generalized piezo-thermoelastic medium under the effect of rotation. The normal mode analysis is used to obtain the expressions for the displacement components, the temperature, the stress and the strain components. Comparisons are made with the results predicted by different theories (Coupled theory, Lord-Schulman, Green-Lindsay) in the absence and presence of rotation.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.245-246
• /
• 2009

정전용량형 후막 스트레인 게이지(piezocapacitive thick film strain gage)는 세라믹 ($Al_2O_3$)을 주 원료로 하는 지지대(약 5mm)와 다이어프램(약 $300{\mu}m$) 그리고 가드 링으로 구성된다. 전극 판은 도전성 페이스트를 이용하여 지지대와 다이어프램에 형성되었으며 극판 사이에는 유전체 메이스트를 사용하여 스크린 인쇄로 후막을 형성하였다. 극판 사이의 가드 링 두께는 약 $30{\mu}m$정도로 다이어프램의 변위 최대값을 유지시키는 데 필요한 간격이다. 따라서 정전용랑형 후막 스트레인 게이지는 지지대를 중심으로 다이어프램에 압력 (0.5~1.0bar)이 인가될 때 변위를 발생시키면서 커패시터 값이 압력의 크기에 따라 비례 특성을 가지고 변화하는 것을 이용한 것이다. 압력이 없을때 초기값은 35pF~40pF 정도이고 정격압력의 최대치를 인가시켰을 때 약 55pF~55p를 나타내었다.

• 한국산학기술학회논문지
• /
• 제10권10호
• /
• pp.2551-2556
• /
• 2009

링 레이저 자이로스콥의 주 동작은 폐경로 내의 상대 전파에 대한 위상 차에 의존한다. 공명 블록위에 설치 된 반사경들이 순항 파를 형성한다. 따라서, 공명 블록의 차원 정확도가 빔의 순항 경로에 영향을 미친다. 링의 공진 내에서 안정된 광학 빔 경로를 유지하기 위해서 피에조로 구동되는 이동거울이 공명 블록의 열팽창이나 기계적 변형하에서 경로치 제어를 하고자 선택되었다. 이 논문에서는 피에조 구동 거울의 탄성거동에 대한 수학적 설명을 제시하였다. 이 설명은 피에조 구동 거울의 개념 설계에도 적용될 수 있다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제5권4호
• /
• pp.215-225
• /
• 2001

Stress waves monitored on the surface of structures under various loading conditions can provide useful information on the structural health status. In this paper, stress waves are measured by several sensors when a steel beam is impacted by a ball drop. The sensors used include the piezo-electric film Sensor, the electrical strain gage, and the ultrasonic transducer, and special attention is given to the pieza film sensor. The wavelet transform is used for the time-frequency analysis of dispersive waves propagating in the beam. The velocities of the wave produced in the team due to the lateral impact is found to be frequency-dependent and identified as the flexural wave velocity based on the comparisons with the Timoshenko beam theory. A linear impact site identification method is developed using the flexural wave, and the impact sites of the beam can be accurately estimated by the piezo film sensors. It is found that the piezo film sensor is appropriate for sensing stress waves due to impact and for locating impact sites in the beam.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.671-674
• /
• 2004

This paper presents design and analysis of multi-layered ring-dot type piezoelectric transformer. These transformers are useful for step up and step down. The transformers consist of disk type multi-layered piezoelectric ceramic plates. The finite element method(FEM) was used for analysis transformer. Vibration mode, electric field and equivalent elastic strain of piezoelectric transformer were simulated by changing frequency. As results, the strain was distributed in isolation part entirely. We can get the operated in step up transformer when the inner side electrode using by input parts. Also we can get the step down transformers using by input Part as outer side electrode. The step up ratio and step down ratio was increased by decreasing inner side electrode. The resonance frequency was increased by increasing inner side electrode when the transformer was operated in step down transformer. But the step up one was decreased. From these results, we can expect to multi-layered ring-dot type piezo transformers as step up and step down transformers.

• Advances in nano research
• /
• 제12권4호
• /
• pp.427-440
• /
• 2022

In the present study, the nonlocal strain gradient theory is used to predict the size-dependent buckling and post-buckling behavior of geometrically imperfect nano-scale piezo-flexomagnetic plate strips in two modes of direct and converse flexomagnetic effects. The first-order shear deformation plate theory is used to analyze analytically nano-strips with simply supported boundary conditions. The nonlinear governing equations of equilibrium and associated boundary conditions are derived using the principle of minimum total potential energy with consideration of the von Kármán-type of geometric nonlinearity. A closed-form solution of governing differential equation is obtained, which is easily usable for engineers and designers. To validate the presented formulations, whenever possible, a comparison with the results found in the open literature is reported for buckling loads. A parametric study is presented to examine the effect of scaling parameters, plate slenderness ratio, temperature, the mid-plane initial rise, flexomagnetic coefficient, different temperature distributions, and magnetic potential, in case of the converse flexomagnetic effect, on buckling and post-buckling loads in detail.

• 한국정밀공학회지
• /
• 제12권2호
• /
• pp.87-96
• /
• 1995

The cutting force is the most important variable to understand the mechanics of ultra-precision machining. Most dynamometers, however, monitor the static cutting force only. But it is necessary to measure the dynamic cutting force to clarify the machinability of the material, the formation of the chip, chatter and the wear of the tool. In this research, measurement of the dynamic cutting force in order to clarify the machin-ability of the material, the formation of the chip, chatter and the wear of the tool has been conducted. A combined-type dynamometer which could measure the static cutting force and the dynamic cutting force by use of strain gauges and a piezo-film accelerometer has been developed. An analysis of the dynamometer also has been carried out.