• Journal of Information Display
• /
• v.12 no.2
• /
• pp.93-96
• /
• 2011

Single-phased $CaZrO_3:Dy^{3+}$, $Tm^{3+}$ series have been successfully synthesized by solid-state reaction, and their luminescence properties were investigated. Under 355 nm excitation, $CaZrO_3:Dy^{3+}$ series showed characteristic emission of $Dy^{3+}$, which exhibited yellowish white color. By introducing $Tm^{3+}$ into the matrix, the emitted hue of the $Dy^{3+}$-doped sample could be easily tailored to white, and simultaneously, energy transfer from $Tm^{3+}$ to $Dy^{3+}$ was observed. The color coordinates of the optimum white-emitting sample were (0.321, 0.323), which were very close to the data of the National Television Standard Committee (0.33, 0.33). The co-activated phosphors presented good match to ultraviolet light-emitting diodes (LEDs), which revealed that they could be novel promising phosphors utilized in white LED application.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.43 no.1
• /
• pp.47-56
• /
• 2011

This study was carried out to investigate the characteristics of the Hanji which had been used for movable types printing volumes of the Joseon Dynasty. A total 29 volumes which had printed with metal and wooden movable types, were examined on the physical properties, fiber morphology, and color reactions. The grammage of all of the Hanji which had been used for movable types printing volumes were $13.10-51.65g/m^2$ and on the average was $25g/m^2$. The apparent density of the Hanji was $0.23-1.65g/cm^3$ and on the average was $0.4g/cm^3$. In almost all movable types printing volumes, the Hanji had undergone Dochim which is a processing of printability improvement. Through the examination on fiber morphology and color reactions, Hanji was investigated into that all of those were made from paper mulberry bast fiber.

• Food Science of Animal Resources
• /
• v.26 no.4
• /
• pp.464-470
• /
• 2006

This study was carried out to investigate the effect of various high pressure freezing treatments on the physical properties of pork To compare the effect of freezing on meat quality, atmospheric freezing (AF), pressure and freezing (PF), pressure shift freezing (USF) and pressure assisted freezing (PAF) were conducted at pressure of 100 MPa. Water binding properties, shear force and colour were measured as physical properties of pork PAF showed shorter phase transition time than PSF. Although significant increase (p<0.05) in water binding properties was found only at PAF, meat frozen under hydrostatic pressure environment showed improved water binding properties. However, all high pressure freezing treatment caused significantly increased shear force (p<0.05), especially at PF treatment. In color, all high pressure freezing treatments showed significantly higher color parameters (p<0.05) than AF, whilst no significant differences among high pressure freezing treatments were found (p>0.05). Therefore the result indicated that applied hydrostatic pressure improved functional properties of pork with increasing freezing rate and PAF had more potential benefit than PSF at mild pressure range.

• The Journal of the Petrological Society of Korea
• /
• v.20 no.3
• /
• pp.141-149
• /
• 2011

Samples (two granites, marble, sandstone) were heated in an electric furnace at temperature $400^{\circ}C$ and $600^{\circ}C$ in order to investigate the change of physical properties of rocks depending on the heating temperature. Changes of Color and physical properties such as specify gravity, porosity, absorption, p-wave velocity are visible while mineralogical changes by using polarizing microscope are not pronounced. In addition, porosity and absorption increased while specific gravity and p-wave velocity decreased at a more higher temperature ($600^{\circ}C$). Although the open porosity does not indicate total porosity of the rock. but p-wave velocity can be used to evaluate the degree of damage Therefore, porosity and p-wave velocity should be compared in order to investigate the change of physical properties of rocks depending on the heating temperature.

• Food Engineering Progress
• /
• v.23 no.2
• /
• pp.118-124
• /
• 2019

This study aims to investigate the physical properties of extruded psyllium husk upon the addition of emulsifiers. Three different emulsifiers-glycerol monostearate (GMS), polyglycerol ester (PGE), and sugar ester (SE)-were added to the mixture of psyllium husk and rice powder before extrusion. Extrusion was performed using a twin-screw extruder at 140℃ die temperature, 200 rpm screw speed, and 16% feed moisture content. The physical properties of psyllium husk extrudates including expansion ratio, specific length, piece density, texture profile, color properties, water soluble index, and water absorption index were evaluated. It was observed that the expansion ratio was the highest while the specific length and piece density were the lowest in the control which had no emulsifiers. Texture profile analysis showed that the apparent elastic modulus and breaking strength were highest in the extrudate with a PGE of 0.1%. The adhesiveness was found to be lowest in the extrudates with an SE of 0.1% and GMS of 0.5%. Lightness value was highest in the extrudate with a PGE of 0.1%. Color difference, water soluble index, and water absorption index were highest in the control. The results reveal that some physical properties of extruded psyllium husk were improved with the addition of emulsifiers. This finding provides useful information for the development of psyllium snacks with good physical characteristics.

• Journal of Technologic Dentistry
• /
• v.38 no.4
• /
• pp.281-290
• /
• 2016

Purpose: The increased aesthetic requirements and demands of patients have resulted in the developments of coloring liquid for zirconia. Methods: In this study, zirconia block was dipped into $Fe(NO_3)_3$solution, which showed a color and then concentration of $Fe(NO_3)_3$and zirconia's color and physical properties depending on the dipping time were observed and compared with exclusive coloring solutions. As the result, the following conclusions were obtained. Results: When compared with the specimens that were colored using exclusive solutions, $L^*$ value rose overall depending on the concentration of $Fe(NO_3)_3$and $a^*$ value was red in the form of (+) in all the specimens. Also, $b^*$ value was in the form of (+) at 0.5 to $1{\ss}fl$, but was in the form of (-) at 1.5 to $2{\ss}fl$. The dipping time did not highly influence $L^*$ value, but $a^*$ value and $b^*$ value were directly opposite to the specimens, which were not colored, except the sample that was dipped for only 2 seconds. When compared with exclusive coloring solutions, $Fe(NO_3)_3$had the most similar color at 0.5 to $1{\ss}fl$ and the longer the coloring time, the higher the rate of color change became. In relation to the density change depending on the addition of $Fe(NO_3)_3$, there was the lowest density at $2{\ss}fl$ and the density was increased in the specimens that were not colored. Conclusion: These results show that $Fe(NO_3)_3$solution can be used to make colored zirconia. It is expected that newly made colored zirconia can be used in clinical practice because the colored zirconia not only possesses the mechanical properties that all ceramic core material should have but also was biocompatible to a living cells.

• Clean Technology
• /
• v.14 no.1
• /
• pp.21-28
• /
• 2008

The properties of the dispersion of the red, green, and blue pigments were investigated for the manufacture of the millbase of LCD color filters. Their physical properties and viscosity were controlled to apply to the screen printing in order to substitute the existing photolithography method. The best dispersion properties were obtained with dispersant BYK-2000 and monomer EB-140. The millbase was pre-mixed at 500 rpm for 30 min, and dispersed at 4000 rpm for 5 - 6 hour by Torus Mill. The resulting particle sizes were $100{\sim}110\;nm$ for red, $50{\sim}70\;nm$ for green, and $60{\sim}80\;nm$ for blue. When the millbase viscosity was 200-300 cps in the low viscosity formulation, an efficient impact of the beads on pigments was achieved. The dispersion properties were confirmed from the rheological behavior and color characteristics.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.43 no.2
• /
• pp.132-139
• /
• 2001

This study deals with coal-mine waste (CMW) for use in concrete as a replacement of normal aggregates. The CMW was collected from Sabuk region. Ganwon-do. Fine and coarse aggregates from CMW were prepared by using a crusher and separating debris with #4 sieve. CMW aggregates showed good physical and mechanical properties with having specific gravity over 2.65, absorption less than 1%, and abrasion ratio below 20%. However, particle shape of CMW was poor because of non-isotropic nature of matrix which cause particles to be long or flat. Since irregular particles caused a poor workability, to make workability better, a 1/4 of coarse aggregate was replaced with normal aggregate together with a superplasticizer. Compressive strength and other mechanical properties of CMW concrete were very good. Color of the concrete was darker than normal concrete due to black color of CMW. In conclusion, characteristics of CMW concrete was acceptable for use as a structural concrete material.

• Journal of Fashion Business
• /
• v.10 no.1
• /
• pp.94-105
• /
• 2006

Hair bleaching is a treatment process in which the melanic pigment is oxidized by hydrogen peroxide. With the increase of the number of treatments, $1{\sim}10$ levels of various colors develop, the hair luster diminishes, and the appearance becomes very rough. In this study, by changing the number of hair bleaching and bleaching conditions, the changes in the degree of hair damage and its process were observed through the use of scanning electron microscopy. The color changes were also compared through the use of spectrophotometer. In order to study the physical changes of the bleached hairs and to search for the optimum conditions to keep the hair damages minimum during bleaching, tensile properties were measured and reviewed. By increasing the number of hair bleaching and by the severe conditions, the scales became eroded and the protection layers were decreased, and the oxidation reached the inner sectors resulting in rough surface and fibrillation. The surface of the hairs became bright yellowish and transparent by the bleaching of melanic pigments or by the destruction of pigments. With the increase of bleaching degree, in terms of physical changes, the breaking strength decreased while the elongation increased a little.

• Textile Coloration and Finishing
• /
• v.18 no.4
• /
• pp.11-19
• /
• 2006

Black-dyed PET fabrics were sputtered with stainless steel through DC-magnetron type device to investigate the possibility of coloration effect, and then considered the morphological structure and physical characteristics such as water permeation ability and washing fastness. Change in color was estimated on the basis of CIELAB color system. The color coordination of metal plated PET was shifted to yellow-red from red-blue. Colour difference$({\Delta}E^*)$ was increased by sputtering conditions with increasing ion current and treatment time. Especially, $Lightness(L^*)$ value of PET was remarkably increased by sputtering, whereas $Chroma(C^*)$ increased gradually. From SEM analysis, rough and uneven craters were found and thickened on the fiber surfaces with longer sputtering time. And washing fastness was a little poor and absorption ability slightly decreased. There were little changes of breaking load and breaking extension. It was evident that observed uneven craters in the plated thin layer resulted in the colour change of PET fabrics by sputtering treatments.