• The Journal of the Convergence on Culture Technology
• /
• v.7 no.1
• /
• pp.564-569
• /
• 2021

In this paper, for the typical LED and the tilted LED, when there is no electrode, when 20% absorption (80% reflection) occurs at the electrode, and when 60% absorption (40% reflection) occurs at the electrode, the effect of the absorption at the electrode and the height of the active region on the photon extraction efficiency and the mean photon path length was investigated, and an appropriate height of the active region was proposed. In a typical LED, as the absorption of the electrode increases, the photon extraction efficiency decreases from 18% to 15% and 13%, and the photon extraction efficiency is highest when the height of the active area is located in the center between the two electrodes. In the tilted LED, as the absorption of the electrode increases, the photon extraction efficiency decreases from 38% to 33% and 25%, and the photon extraction efficiency is highest when the height of the active area is located in the center between the two electrodes. The tilted LED can increase the photon extraction efficiency more than twice than that of a typical LED, where photons are trapped inside the chip due to total reflection.

• Journal of the Optical Society of Korea
• /
• v.20 no.2
• /
• pp.228-233
• /
• 2016

In this paper, we propose a nonlinear maximum average correlation height (MACH) filter for information authentication of photon counting double random phase encryption (DRPE). To enhance the security of DRPE, photon counting imaging can be applied because of its sparseness. However, under severely photon-starved conditions, information authentication of DRPE may not be implemented successfully. To visualize the photon counting DRPE, a three-dimensional imaging technique such as integral imaging can be used. In addition, a nonlinear MACH filter can be utilized for helping the information authentication. Therefore, in this paper, we use integral imaging and nonlinear MACH filter to implement the information authentication of photon counting DRPE. To verify our method, we implement optical experiments and computer simulation.

• Nuclear Engineering and Technology
• /
• v.53 no.11
• /
• pp.3759-3763
• /
• 2021

In this study, 3" × 3" NaI(Tl) detector, which is widely used in gamma spectroscopy, was modeled with FLUKA code, and calculations required to determine the detector's energy resolution were reported. Photon beams with isotropic distribution with 59, 81, 302, 356, 511, 662, 835, 1173, 1275, and 1332 keV energy were used as radiation sources. The photon pulse height distribution of the NaI(Tl) without influence of its energy resolution obtained with FLUKA code has been converted into a real NaI(Tl) response function, using the necessary conversion process. The photon pulse height distribution simulated in the conversion process was analyzed using the ROOT data analysis framework. The statistical errors of the simulated data were found in the range of 0.2-1.1%. When the results, obtained with FLUKA and ROOT, are compared with the literature data, it is seen that the results are in good agreement with them. Thus, the applicability of this procedure has been demonstrated for the other energy values mentioned.

• Journal of Radiation Protection and Research
• /
• v.26 no.3
• /
• pp.203-206
• /
• 2001

The mathematical processing (unfolding) of pulse height spectra from a scintillation detector helps to calculate the photon fluence rate energy distribution in a measured photon field. The data processing is based on the knowledge of detection system response function and directional dependence respectively. The experimental results of the photon fields measurements in the vicinity of the spent fuel temporary storage and inside the storage hall are presented. The containers Castor 440 are used for temporary storing of the burnt up fuel assemblies in the Czech nuclear power plant Dukovany. A set of periodical measurements was performed in order to get basic information on the time dependence of the photon fields spatial distributions and spectral characteristics in the temporary storage hall and its vicinity. The photon fields were measured by the scintillation system. The obtained photon fields spatial distributions and spectral characteristics present the information on the radiation hazard in the storage.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.02a
• /
• pp.22-23
• /
• 2003

The new method of x-ray photon correlation spectroscopy (XPCS) [1] is developed recently for probing the dynamics of surface height fluctuations as a function of lateral length scale. Measurements were performed on supported polystyrene (PS) films of thicknesses varying from 84 to 333 nm at temperatures above the PS glass transition temperature. Within a range of wave vectors spanning $10^{-3}$ to $10^{-2}$ $nm^{-1}$, good agreement is found between the measured surface dynamics and the theory of overdamped thermal capillary waves on thin films. Quantitatively, the data can be accounted for using the viscosity of bulk PS. (omitted)

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.47 no.5
• /
• pp.368-373
• /
• 2002

The strip intercropping system has used due to many advantages. Many researches supported these crop systems are usually equal to or better than monoculture crop systems in both total production and profit. There was no research to examine the important ecological factors in the competition between crops. A strip intercropping system composed of adjacent narrow strips of corn, soybean, and oat/legumes has been investigated in Iowa, USA. This study conducted to investigate why and how the differences in soybean yield are produced and affected by light, one of the microclimate, of the strip intercropping system. In height, the two rows of soybean closest to corn were taller than the two rows near the then-empty oat strip. The height of each crop decreased as the amount of light received increased. Weight of plant parts was lowest in row 1, nearest corn, and highest in row 4, next to the vacant oat strip. Daily photon flux density(PFD) increased with increasing distance from corn, with the highest value occurring on the edge next to the empty oat strip. Analyses of the relationship between light and biomass of soybean showed that all biomass measurements had a positive relationship to total PFD per day except height.

• Journal of Sensor Science and Technology
• /
• v.23 no.1
• /
• pp.29-34
• /
• 2014

A dosimeter using tissue-equivalent scintillator by photon-counting method was developed and evaluated in its performance. The dosimeter is portable and can be operated by low power from lap-top computer. A data-acquisition software of the dosimeter system was developed by Labwindows/CVI based on Windows. The energy to channel ratio for energy calibration was 0.839 keV/ch. obtained from pulse height spectrum of $^{137}Cs$ and $^{60}Co$ gamma-ray. Using the dosimeter system, the absorbed dose of environmental radiation in Gyungju was 0.18 ${\mu}Sv/h$.

• Polymer(Korea)
• /
• v.29 no.4
• /
• pp.418-421
• /
• 2005

Three-dimensional (3D) microfabrication process using two-photon polymerization (TPP) is developed to fabricate the curved microstructures in a layer, which can be applied potentially to optical MEMS, nano/micro-devices, etc. A 3D curved structure can be expressed using the same height-contours that are defined by symbolic colors which consist of 14 colors. Then, the designed bitmap figure is transformed into a multi-exposure voxel matrix (MVM). In this work a multi-exposure voxel matrix scanning method is used to generate various heights of voxels according to each laser exposure time that is assigned to the symbolic colors. An objective lens with a numerical aperture of 1.25 is employed to enlarge the variation of a voxel height in the range of 1.2 to 6.4 um which can be controlled easily using the various exposure time. Though this work some 3D curved micro-shapes are fabricated directly to demonstrate the usefulness of the process without a laminating process that is generally required in a micro-stereolithography process.

• Korean Journal of Remote Sensing
• /
• v.37 no.5_1
• /
• pp.1177-1186
• /
• 2021

As the Arctic melt ponds play an important role in determining the interannual variation of the sea ice extent and changes in the Arctic environment, it is crucial to monitor the Arctic melt ponds with high accuracy. Ice, Cloud, and Land Elevation Satellite-2 (ICESat-2), which is the NASA's latest altimeter satellite based on the green laser (532 nm), observes the global surface elevation. When compared to the CryoSat-2 altimetry satellite whose along-track resolution is 250 m, ICESat-2 is highly expected to provide much more detailed information about Arctic melt ponds thanks to its high along-track resolution of 70 cm. The basic products of ICESat-2 are the surface height and the number of reflected photons. To aggregate the neighboring information of a specific ICESat-2 photon, the segments of photons with 10 m length were used. The standard deviation of the height and the total number of photons were calculated for each segment. As the melt ponds have the smoother surface than the sea ice, the lower variation of the height over melt ponds can make the melt ponds distinguished from the sea ice. When the melt ponds were extracted, the number of photons per segment was used to classify the melt ponds covered with open-water and specular ice. As photons are much more absorbed in the water-covered melt pondsthan the melt ponds with the specular ice, the number of photons persegment can distinguish the water- and ice-covered ponds. As a result, the suggested melt pond detection method was able to classify the sea ice, water-covered melt ponds, and ice-covered melt ponds. A qualitative analysis was conducted using the Sentinel-2 optical imagery. The suggested method successfully classified the water- and ice-covered ponds which were difficult to distinguish with Sentinel-2 optical images. Lastly, the pros and cons of the melt pond detection using satellite altimetry and optical images were discussed.

• Journal of Biosystems Engineering
• /
• v.33 no.2
• /
• pp.106-114
• /
• 2008

This study was performed to analyze the distribution of air current speed, $CO_2$ concentration, and photosynthetic photon flux (PPF) in a closed transplants production system (CTPS) for producing quality transplants. And the effect of PPF on the growth of potato (Solanum tuberosum L. cv. Dejima) plug seedlings was analyzed. Uniformity of the air current speed in CTPS was improved by installing perforated floors in duct for air circulating and by adjusting of air flow rate of the fan connected to air conditioning unit used in this study, Measured $CO_2$ concentrations were measured $409{\pm}13$, $950{\pm}25$, and $1,550{\pm}35\;{\mu}mol{\cdot}mol^{-1}$ for setting values of 400, 950, and $1,550\;{\mu}mol{\cdot}mol^{-1}$, respectively. Uniformity of PPF by adding each one the single fluorescent lamp of 20 W at both ends of the single fluorescent lamps of 40 W was highly improved. While the average PPF measured under the twin fluorescent lamps of 55 W installed at regular intervals of 10 cm was decreased by increasing the vertical distance from the lighting sources, the ratio of average PPF measured at both ends to PPF measured in the center was 74-79%. Five levels ($100{\pm}9$, $150{\pm}14$, $200{\pm}17$, $250{\pm}24$ and $300{\pm}31{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$) of PPF were provided to investigate the effect of PPF on plant height, fresh weight and dry weight of potato plug seedlings produced in CTPS. Plant height was decreased by increasing PPF. Maximum fresh weight and dry weight were shown under PPF of $250{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$. Thus PPF of $250\;{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ was enough to produce quality potato transplants under air temperature, photoperiod, and relative humidity of $20^{\circ}C$, 16/8 h, and 70%, respectively. It was concluded that quality indices such as plant height, fresh weight and dry weight could be improved by illuminating of adequate PPF from artificial lighting sources.